1. Manuals
  2. Brands
  3. HP Manuals
  4. Storage
  5. StorageWorks 1510i - Modular Smart Array
  6. Service manual

HP StorageWorks 1510i - Modular Smart Array Service Manual

Hp storageworks 1510i modular smart array maintenance and service guide (383072-002, july 2008)
Hide thumbs Also See for StorageWorks 1510i - Modular Smart Array:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
HP StorageWorks
1510i Modular Smart Array maintenance and
service guide
Part number: 383072–002
Second edition: May 2008

Advertisement

Table of Contents
loading

Related Manuals for HP StorageWorks 1510i - Modular Smart Array

Summary of Contents for HP StorageWorks 1510i - Modular Smart Array

  • Page 1 HP StorageWorks 1510i Modular Smart Array maintenance and service guide Part number: 383072–002 Second edition: May 2008...
  • Page 2 © Copyright 2005, 2008 Hewlett-Packard Development Company, L.P. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.

  • Page 3: Table Of Contents

    Contents About this guide ......Intended audience ........Prerequisites .
  • Page 4 Returning the defective component ......Recommended tools ........Warnings and precautions .
  • Page 5 Installing the power supply module ......Verifying proper operation ....... Replacing the MSA1510i chassis .
  • Page 6 Latvian notice ........Lithuanian notice .

  • Page 7: About This Guide

    About this guide This guide provides information about: • Maintaining the MSA1510i • Servicing the MSA1510i • Troubleshooting the MSA1510i WARNING! To reduce the risk of personal injury from electric shock and hazardous energy levels, do not exceed the level of repairs specified in these procedures. Troubleshooting and repair procedures included in this document are detailed to allow only subassembly/module-level repair.

  • Page 8: Document Conventions And Symbols

    In addition to MSA1510i-specific documents, the following guide, available on the SAN Infrastructure website: http://www.hp.com/go/san, includes detailed, helpful information about Fibre Channel and iSCSI networks: • HP SAN Design reference guide The following iSCSI-related technical information is available on the Internet Engineering Task Force website: http://www.ietf.org/rfc.

  • Page 9: Rack Stability

    TIP: Provides helpful hints and shortcuts. Rack stability WARNING! To reduce the risk of personal injury or damage to equipment: • Extend leveling jacks to the floor. • Ensure that the full weight of the rack rests on the leveling jacks. •...

  • Page 10: Documentation Feedback

    • http://www.hp.com/go/storage • http://www.hp.com/go/servers • http://www.hp.com/service_locator • http://www.hp.com/support • http://www.hp.com/support/manuals • http://www.hp.com/support/downloads Documentation feedback HP welcomes your feedback. To make comments and suggestions about product documentation, please send a message to StoragedocsFeedback@hp.com. All submissions become the property of HP. About this guide...

  • Page 11: Illustrated Parts List

    1 Illustrated parts list This section provides an illustrated parts breakdown and spare parts list for the HP StorageWorks 1510i Modular Smart Array (MSA1510i). Service replacement Additional/optional Item Description Customer Self Repair module part number module part number Standard shipping configuration items: 349800–001 / Power supply modules Mandatory...
  • Page 12 MSA1510i controller 417787–001 AD539–04001 with 256 MB cache Optional module and batteries MSA controller 229208–001 Mandatory blanking panel Shipped items not illustrated: Contact your HP AC power cords Contact HP Support Mandatory Authorized Reseller Custom serial cable 316131–001 Mandatory for CLI connection Other available items: Contact your Contact HP Support...

  • Page 13: Specifications

    2 Specifications This section provides operating and performance specifications for the MSA1510i. Included in this section: • Chassis specifications • 2-Port Ethernet iSCSI module specifications • Fan module specifications • SCSI I/O module specifications • Power supply module specifications NOTE: For additional information on components and their part numbers, see Illustrated parts list.

  • Page 14: Chassis Specifications

    Chassis specifications Parameter Value 8.79 cm (3.46 in) Height 48.41 cm (19.06 in) Width 61.77 cm (24.32 in) Depth Weight 24.95 kg (55 lb) Input voltage requirements Rated input voltage 100 to 240 VAC 50 Hz to 60 Hz Rated input frequency Rated input current 6.4A Max, 1A typical Input power (max)

  • Page 15: Fan Module Specifications

    Fan module specifications Parameter Value Height 6.0 cm (2.36 in) Width 6.0 cm (2.36 in) 26.8 cm (10.6 in) Depth Weight 0.50 kg (1.10 lbs) SCSI I/O module specifications Parameter Value Height 8.13 cm (3.2 in) 2.34 cm (0.92 in) Width 37.14 cm (14.62 in) Depth...
  • Page 16 Specifications...

  • Page 17: System Components And Leds

    3 System components and LEDs This chapter includes figures and tables that identify system components and describe chassis and module LEDs patterns. • Front view • Rear view • Chassis and component LEDs Front view 1. Chassis LEDs 2. Chassis Power On/Standby button 3.

  • Page 18: Rear View

    Rear view 1. 2–Port Ethernet iSCSI module (for the controller in slot 1) 2. Chassis slot diagram 3. Blank for additional 2-Port Ethernet iSCSI module (for the controller in slot 2) 4. Power supply module 2 5. Power supply module 1 6.

  • Page 19: Chassis And Component Leds

    Chassis and component LEDs The MSA chassis and its modular components are equipped with LEDs. When the fault LED on any MSA component is amber, promptly determine the reason for the alert by examining the component, the messages displayed on the MSA controller LCD panel, and system event logs (such as those provided by HP Systems Insight Manager).

  • Page 20: Controller Leds

    NOTE: System power does not shut off completely with the power button. Standby removes power from most of the electronics and the hard drives, but portions of the power supply and some internal circuitry remain active. To remove the power completely, disconnect all power cords from the device. For instructions, “Powering off the MSA1510i”...

  • Page 21: Hard Drive Leds

    Item Name Meaning Condition Color SCSI bus 3 activity Green There is activity on this SCSI bus. SCSI bus 2 activity Green There is activity on this SCSI bus. SCSI bus 1 activity Green There is activity on this SCSI bus. Green SCSI bus 0 activity There is activity on this SCSI bus.
  • Page 22 Item 1 Item 2 Item 3 Meaning Activity LED Online LED Fault LED The hard drive is being accessed in one of the following ways: • The hard drive is not configured as part of an array. • The hard drive is a replacement and rebuild has not yet started. •...

  • Page 23: Sata Hard Drive Leds

    SATA hard drive LEDs Each SATA hard drive has two LEDs. The following figure and table describe their locations and meanings. Item 2 Item 1 Fault/ Online/ UID LED Meaning Activity LED (amber/ (green) blue) Alternating On, off, or The drive has failed, or a predictive failure alert has been received for this drive; it also has amber and blinking been selected by a management application.

  • Page 24: Slot Diagram Leds

    Slot diagram LEDs Located on the rear of the MSA, the slot diagram provides information about MSA modules. 1. 2–Port Ethernet iSCSI module (for the controller in slot 2) 2. SCSI I/O module (bus 3) 3. SCSI I/O module (bus 2) 4.

  • Page 25: 2-Port Ethernet Iscsi Module Leds

    2-Port Ethernet iSCSI module LEDs The 2-Port Ethernet iSCSI module has one LED to show the status of the module, and each port has two LEDs to show status and activity information for the specific port. Item Name Condition Color Meaning Power is on, the module is operational, and communication...

  • Page 26: Fan Module Leds

    Fan module LEDs Each fan module has one bi-color LED. This LED can be illuminated with either a green or amber color. The following figure and table describes their locations and meanings. Item Name Condition Color Meaning Solid Green The power is on. Status —...

  • Page 27: Scsi I/O Module Leds

    SCSI I/O module LEDs The SCSI I/O module has two LEDs. The following figure and table describes their locations and meanings. Item Name Condition Color Description Green Solid The power is on. Status — The power is off. There is activity on this SCSI Blinking Green module.

  • Page 28: Power Supply Module Leds

    Power supply module LEDs The power supply uses a single bi-color LED to indicate status. This LED can be illuminated with either a green or amber color. The following figure and table describes their locations and meanings. Item Name Description Condition Color Green...

  • Page 29: Available Diagnostic Tools

    4 Available diagnostic tools The following is a partial list of tools that are supported for use with the MSA: • Storage Management Utility (SMU) overview • MSA Command Line Interface (MSA-CLI) overivew • HP Systems Insight Manager (HP-SIM) overview •...

  • Page 30: Packet Internet Groper (Ping) Overview

    third-party devices. HP-SIM reports hardware fault conditions (both failure and pre-failure) and collects data for reporting and graphing. HP-SIM also provides base-level management of HP clients, printers, and selected storage. HP recommends using HP-SIM to monitor the performance of your Windows, Linux, and NetWare systems. IMPORTANT: You must install and use HP-SIM to benefit from the Pre-Failure Warranty for processors, SAS, SCSI, and SATA hard drives, and memory modules.

  • Page 31: Customer Replaceable Components

    5 Customer replaceable components This chapter includes the following information regarding the removal and replacement of MSA components: • Procedural overview • Customer self repair • Recommended tools • Warnings and precautions • Determining whether the component is hot-pluggable • Powering off and powering on the MSA •...

  • Page 32: Customer Self Repair

    Verification procedures may include: • Viewing status and error messages sent to the controller LCD panel. • Viewing the LED illumination patterns on the MSA and the component. • Viewing system event logs or other reports generated by system-management tools, such as HP-SIM. Customer self repair HP products are designed with many Customer Self Repair (CSR) components to minimize repair time and allow for greater flexibility in performing defective parts replacement.

  • Page 33: Recommended Tools

    billing you for the replacement. With a CSR, HP will pay all shipping and part return costs and determine the courier/carrier to be used. Recommended tools When replacing certain components, such as the power button assembly, the following tools may be necessary: •...

  • Page 34: Equipment Symbols

    If you do not have any of the suggested equipment for proper grounding, have an Authorized HP Reseller install the part. NOTE: For more information on static electricity or assistance with product installation, contact your HP Authorized Reseller. Equipment symbols The following symbols may be located on equipment in areas where hazardous conditions may exist.

  • Page 35: Weight Warning

    Weight warning WARNING! The device can be very heavy. To reduce the risk of personal injury or damage to equipment: • Remove all hot-pluggable power supplies and modules to reduce the overall weight of the device before lifting. • Observe local health and safety requirements and guidelines for manual material handling. •...

  • Page 36: Device Warnings And Precautions

    WARNING! Verify that the AC power supply branch circuit that provides power to the rack is not overloaded. Overloading AC power to the rack power supply circuit increases the risk of personal injury, fire, or damage to the equipment. The total rack load should not exceed 80 percent of the branch circuit rating. Consult the electrical authority having jurisdiction over your facility wiring and installation requirements.

  • Page 37: Determining Whether A Component Is Hot-Pluggable

    CAUTION: To properly ventilate the system, you must provide at least 7.6 centimeters (3.0 inches) of clearance at the front and back of the device. CAUTION: When replacing hot-pluggable components in an operational MSA, allow approximately 30 seconds between removing the failed component and installing the replacement. This time is needed to ensure that configuration data about the removed component is cleared from the system registry.

  • Page 38: Powering Off And Powering On The Msa

    Component Hot-pluggable Non- hot-pluggable Redundant power supply module Redundant fan module MSA array controller (dual–controller configurations) 2–Port Ethernet iSCSI module (dual–controller configurations) SCSI I/O module MSA chassis MSA array controller (single–controller configurations) 2–Port Ethernet iSCSI module (single–controller configurations) MSA array controller (single–controller configurations) * Before removing one of the two controllers or 2-Port Ethernet iSCSI modules in an operational, dual-controller MSA, the controller being removed must first be disabled.

  • Page 39: Powering On The Msa

    Verify that the Power on/Standby button LED is amber/off and that the fans are off. Power off all attached hard drive enclosures. Disconnect the power cords from the MSA. Powering on the MSA Verify that the following devices are powered on and in a ready state: •...

  • Page 40: Removing Or Installing A 2-Port Ethernet Iscsi Blank

    Removing or installing a 2-Port Ethernet iSCSI blank Before you begin CAUTION: • Before removing a component or blank from an operational device, make sure that you have the replacement part or blank available. Removing a component or blank impacts the airflow pattern and cooling ability of the device.

  • Page 41: Removing Or Installing A Hard Drive Blank

    Removing or installing a hard drive blank Before you begin CAUTION: • Before removing a component or blank from an operational device, make sure that you have the replacement part or blank available. Removing a component or blank impacts the airflow pattern and cooling ability of the device.

  • Page 42: Replacing A Hard Drive

    Replacing a hard drive Before you begin CAUTION: • Before removing a component or blank from an operational device, make sure that you have the replacement part or blank available. Removing a component or blank impacts the airflow pattern and cooling ability of the device. Allow approximately 30 seconds before installing the new or replacement component to ensure that configuration data about the removed component is cleared from the system registry, but, to avoid possible overheating, insert the new or replacement component within one or two minutes.

  • Page 43: Verifying Component Failure

    • Do not remove a failed second hard drive from an array until the first failed or missing hard drive has been replaced and the rebuild process is complete. (When the rebuild is complete, the online LED on the front of the hard drive stops blinking.) Exceptions: •...

  • Page 44: Installing The Hard Drive

    Press the ejector button (1) and pull the release lever to the full open position (2). IMPORTANT: Wait approximately 10 seconds for the internal disk to stop spinning before pulling the hard drive out of the enclosure. Handling a hard drive while the internal media is spinning can damage the media.

  • Page 45: Verifying Proper Operation

    Slide the replacement hard drive into the same bay from which the old hard drive was just removed, making sure that the lever is in the full open position to ensure a correct latch. Then, push the hard drive into the bay as far as it will go, pressing firmly on the hard drive to make sure that it is seated properly (1).

  • Page 46: Replacing The Controller, Controller Cache, Or Controller Battery

    Replacing the controller, controller cache, or controller battery The following sections detail procedures for replacing an MSA array controller, controller cache module, or controller cache battery pack: • Before you begin • Verifying component failure • Removing the controller • Removing the controller cache module •...

  • Page 47: Verifying Component Failure

    Verifying component failure Before replacing the controller, cache module, or battery pack: • Check the controller LCD display panel for error messages. • Record any Failure LEDs or LCD panel messages for reference purposes. • Check the controller Heartbeat LED (1) . If the LED is not blinking, it might indicate a failure. •...

  • Page 48: Removing The Controller Cache Battery Pack

    • and you are replacing a cache module with another module of the same size, you can remove one of the controllers and replace the module on that controller while the system is running. • and you are replacing a cache module with a module of a different size, you must schedule a maintenance window and remove power from the system to then change the cache module on both controllers at the same time.
  • Page 49 CAUTION: Do not dispose of batteries, battery packs, and accumulators with general household waste. Use the public collection system or return them to HP, your authorized HP Partners, or their agents. NOTE: • Always replace batteries in pairs, not individually. •...

  • Page 50: Installing The Controller Cache Battery Pack

    Lift the pack upward to unhook the top of the battery pack. Wait approximately 15 seconds after removing the old battery to allow the battery charge monitor to reset. NOTE: If you do not wait 15 seconds after removing the old battery, full charge of the new cache battery is delayed.

  • Page 51: Installing The Controller Cache Module

    Verify that the top hook (1) and bottom clip (2) on the battery pack are securely attached to the cache module. 15520 Repeat step 4 through step 6 to install the second battery pack on the module. Install the serviced cache module in the controller as instructed in Installing the controller cache module.

  • Page 52: Installing The Controller

    Installing the controller Insert the new or serviced array controller into the MSA chassis controller bay (1). Push the controller in as far as it will go, making sure that the controller is seated, and then press the latch handle inward until it is flush against the front panel (2). 15493 If necessary, power on the MSA as instructed in Powering on the...

  • Page 53: Replacing A 2-Port Ethernet Iscsi Module

    Replacing a 2-Port Ethernet iSCSI module Before you begin CAUTION: • Before removing a component or blank from an operational device, make sure that you have the replacement part or blank available. Removing a component or blank impacts the airflow pattern and cooling ability of the device.

  • Page 54: Installing The 2-Port Ethernet Iscsi I/O Module

    Lift the port-colored 2-Port Ethernet iSCSI module latch (1) and pull the module out of the enclosure (2). Installing the 2-Port Ethernet iSCSI I/O module Slide the replacement 2-Port Ethernet iSCSI module into the MSA chassis bay until the module clicks into place.

  • Page 55: Replacing A Fan Module

    Replacing a fan module The variable-speed fan module is hot-pluggable, so it is not necessary to power down the system to replace it. Before you begin CAUTION: • Before removing a component or blank from an operational device, make sure that you have the replacement part or blank available.

  • Page 56: Verifying Proper Operation

    15210 Verifying proper operation After replacing the fan module, verify that: The fan starts operating immediately. • • The fan Status LED is On. • No new error messages are displayed on the array controller LCD panel. newpage pi Customer replaceable components...

  • Page 57: Replacing A Scsi I/O Module

    Replacing a SCSI I/O module Before you begin CAUTION: • Before removing a component or blank from an operational device, make sure that you have the replacement part or blank available. Removing a component or blank impacts the airflow pattern and cooling ability of the device.

  • Page 58: Installing The Scsi I/O Module

    Lift the port-colored SCSI I/O module latch (1) and pull the SCSI I/O module out of the chassis (2). Installing the SCSI I/O module Slide the replacement SCSI I/O module into the MSA chassis bay until the module clicks into place. Reconnect all SCSI cables.

  • Page 59: Replacing A Power Supply Module

    Replacing a power supply module The power supply is hot pluggable, so it is not necessary to power down the system to replace it. Before you begin CAUTION: • Before removing a component or blank from an operational device, make sure that you have the replacement part or blank available.

  • Page 60: Installing The Power Supply Module

    Installing the power supply module Slide the replacement power supply module into the MSA chassis bay until the module clicks into place. Connect the AC power cord to the power supply. Verifying proper operation After replacing the power supply, verify that: •...

  • Page 61: Replacing The Msa1510I Chassis

    Replacing the MSA1510i chassis When replacing a chassis, components are removed from the failed chassis and then installed in the replacement. Components that are moved include the following: • 2-Port Ethernet iSCSI modules • Fan modules • SCSI I/O modules •...

  • Page 62: Removing The Chassis Components

    Removing the chassis components Prepare for the replacement Review all warnings, cautions, and preparation procedures as detailed in Warnings and precautions. If the MSA is operational, stop all access to the MSA. Press and hold the Power on/Standby button for five seconds to place the MSA in Standby mode. Label each cable carefully and then disconnect all of the cables.

  • Page 63: Remove The Scsi I/O Modules

    Remove the SCSI I/O modules Lift the port-colored latch and pull the module out of the chassis. Remove all other SCSI I/O modules or blanks. Remove the power supply modules Press the port-colored latch towards the side of the module and pull the module out of the chassis. Remove the other module.

  • Page 64: Remove The Msa From The Rack

    Grasp the latch handle and pull the controller out of the chassis. Remove the other controller or blank. Remove the MSA from the rack Remove the decorative bezel from the front of the MSA by grasping the outside edges and pulling with sufficient force to disengage the retaining clips.

  • Page 65: Install The Controllers

    Attach the decorative bezel on the front of the MSA by aligning the pins and retaining clips on the back of bezel with the corresponding locations on the front of the chassis. Then, with even pressure, push firmly on the bezel until the retaining clips engage. Install the controllers Press the controller thumb latch and rotate the latch handle out.

  • Page 66: Install The Scsi I/O Modules

    Install the SCSI I/O modules Slide the module into the chassis SCSI I/O slot until the latch clicks into place. Install all other SCSI I/O modules or blanks. Install the fan modules Slide the module into the chassis fan slot until the latch clicks into place. Install the other fan module.

  • Page 67: Install The 2-Port Ethernet Iscsi I/O Modules

    Install the 2-Port Ethernet iSCSI I/O modules Slide the module into the chassis network interconnect slot until the latch clicks into place. NOTE: The following illustration demonstrates installing a Fibre Channel I/O module in the chassis. For the MSA1510i, the 2–Port Ethernet iSCSI I/O module is in this slot. Install the other I/O module or blank.

  • Page 68: Verifying Proper Operation

    Read the controller LCD panel messages during the MSA startup routine. • If the following messages are displayed, the serial number of the original chassis was automatically transferred to the replacement chassis. SPARE CHASSIS DETECTED CHASSIS SERIAL NUMBER FLASHED UPDATED IMPORTANT: If these messages are displayed, the MSA1510i will automatically restart.

  • Page 69: A Regulatory Compliance And Safety

    A Regulatory compliance and safety Federal Communications Commission notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules.

  • Page 70: Modifications

    Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the user's authority to operate the equipment. Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and Regulations.

  • Page 71: International Notices And Statements

    International notices and statements Canadian notice (Avis Canadien) Class A equipment This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

  • Page 72: Japanese Notice

    Japanese notice Korean notice (A&B) Class A equipment Class B equipment Regulatory compliance and safety...

  • Page 73: Safety

    Safety Battery Replacement notice WARNING! The computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not properly handled. To reduce the risk of personal injury: •...

  • Page 74: Electrostatic Discharge

    Electrostatic discharge To prevent damage to the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device.

  • Page 75: Danish Notice

    místo pro recyklaci elektrických a elektronických zařízení. Okamžité třídění a recyklace odpadu pomůže uchovat přírodní prostředí a zajistí takový způsob recyklace, který ochrání zdraví a životní prostředí člověka. Další informace o možnostech odevzdání odpadu k recyklaci získáte na příslušném obecním nebo městském úřadě, od firmy zabývající...

  • Page 76: Finnish Notice

    See tootel või selle pakendil olev sümbol näitab, et kõnealust toodet ei tohi koos teiste majapidamisjäätmetega kõrvaldada. Teie kohus on oma seadmete jäätmed kõrvaldada, viies need elektri- ja elektroonikaseadmete jäätmete ringlussevõtmiseks selleks ettenähtud kogumispunkti. Seadmete jäätmete eraldi kogumine ja ringlussevõtmine kõrvaldamise ajal aitab kaitsta loodusvarasid ning tagada, et ringlussevõtmine toimub viisil, mis kaitseb inimeste tervist ning keskkonda.

  • Page 77: Hungarian Notice

    Το σύμβολο αυτό στο προϊόν ή τη συσκευασία του υποδεικνύει ότι το συγκεκριμένο προϊόν δεν πρέπει να διατίθεται μαζί με τα άλλα οικιακά σας απορρίμματα. Αντίθετα, είναι δική σας ευθύνη να απορρίψετε τον άχρηστο εξοπλισμό σας παραδίδοντάς τον σε καθορισμένο σημείο συλλογής για την ανακύκλωση...

  • Page 78: Lithuanian Notice

    Lithuanian notice Vartotojų iš privačių namų ūkių įrangos atliekų šalinimas Europos Sąjungoje Šis simbolis ant gaminio arba jo pakuotės rodo, kad šio gaminio šalinti kartu su kitomis namų ūkio atliekomis negalima. Šalintinas įrangos atliekas privalote pristatyti į specialią surinkimo vietą elektros ir elektroninės įrangos atliekoms perdirbti.

  • Page 79: Slovenian Notice

    Slovenian notice Odstranjevanje odslužene opreme uporabnikov v zasebnih gospodinjstvih v Evropski uniji Ta znak na izdelku ali njegovi embalaži pomeni, da izdelka ne smete odvreči med gospodinjske odpadke. Nasprotno, odsluženo opremo morate predati na zbirališče, pooblaščeno za recikliranje odslužene električne in elektronske opreme. Ločeno zbiranje in recikliranje odslužene opreme prispeva k ohranjanju naravnih virov in zagotavlja recikliranje te opreme na zdravju in okolju neškodljiv način.
  • Page 80 Regulatory compliance and safety...

  • Page 81: Index

    Index Symbols CLI serial cable part numbers, 12 bezel cloning of firmware between controllers, 39 part numbers, 1 1 Command Line Interface, overview, 29 2-Port Ethernet iSCSI module component failure LEDs, 25 hard drive, more information, 43 part numbers, 1 1 hard drive, verifying, 43 replacing, 53...
  • Page 82 electrostatic sensitive parts HP Systems Insight Manager handling, 33 monitoring packaging, 33 parameters, 30 storing, 33 MSA controller parameters, 30 transporting, 33 HP Systems Insight Manager, overview, 29 ESD (electrostatic discharge) HP-SIM precautions, 33 monitoring preventing, 33 parameters, 30 MSA controller parameters, 30 HP-SIM, overview, 29...
  • Page 83 MSA1510i power illustrated parts breakdown and spare parts applying to the MSA1510i, 39 list, 1 1 completely remove, 38 powering off and on, 38 power on/standby, 38 MSA1510i powering down, 38 powering off, 20 procedures MSA1510i chassis powering down hard drive enclosures, 38 replacement removing, 38...
  • Page 84 replacing 2–Port Ethernet iSCSI module, 53 technical support module, 55 HP, 9 hard drive, 42 service locator website, 9 best practices, 42 thermal failure, caution, 41 MSA1510i chassis tools components, 61 required for servicing, 33 power supply module, 59 type recommended, 33 SCSI I/O module, 57...

Table of Contents