Download
Share
Print this page
HP StorageWorks 1200s - NAS Installation Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Software
  5. NAS 1200s
  6. Installation manual
HP StorageWorks 1200s - NAS Installation Manual

HP StorageWorks 1200s - NAS Installation Manual

Hp storageworks nas 1200s v1.0 installation guide addendum (april 2004)
Hide thumbs Also See for StorageWorks 1200s - NAS:
1
2
3
4
5
6
7

Advertisement

Quick Links

Download this manual
hp StorageWorks
NAS 1200s Installation Guide
Product Version: 1
This addendum applies only to the following document:
HP StorageWorks NAS 1200s Installation Guide
351698-001 (September 2003)
An addendum is comprised of two parts:
Pen-and-ink
text, replacing text with new text, or adding new text at a specific location.
Page
recommends how to attach the replacement pages.
Note:
used, potential problems might arise from using obsolete information.
© Copyright 2004 Hewlett-Packard Development Company, L.P.
Printed in the U.S.A.
Product names mentioned herein may be trademarks of their respective companies as reflected
by an associated footnote. The information in this document is subject to change without notice.
changes—provides instructions for locating specific text and for either deleting
additions—identifies where to add a page at a specific place in the document and
If the changes within this addendum are not incorporated into the specified documents and then
Addendum
367499-001
March 2004

Advertisement

loading

Related Manuals for HP StorageWorks 1200s - NAS

Summary of Contents for HP StorageWorks 1200s - NAS

  • Page 1 Note: If the changes within this addendum are not incorporated into the specified documents and then used, potential problems might arise from using obsolete information. © Copyright 2004 Hewlett-Packard Development Company, L.P. 367499-001 Printed in the U.S.A. March 2004 Product names mentioned herein may be trademarks of their respective companies as reflected by an associated footnote.
  • Page 2 Pen-and-ink changes Pen-and-ink changes For each document, incorporate the required change listed in Table Table 1: Pen-and-ink changes For Document... page... Under Section... Make this Change... 351698-001 Copyright UNIX® is a registered trademark of The Open Group. 351698-001 Configuring the NAS Remove step 3, “Configure the NAS 1200s 1200s device using Chapter 3 of this...

  • Page 3: Replacing A Failed Hard Drive

    Page Additions Replacing a failed hard drive Follow these steps to install the hot-pluggable hard drive into the system: 1. Remove the NAS 1200s front bezel. a. Locate the two bezel latches found on the side of the bezel. Pull the latches outward. b.
  • Page 4 Replacing a failed hard drive Figure 8: Disk Management screen Ensure the appropriate disk is selected when the Upgrade to Dynamic Disk dialog box is displayed. Figure 9: Upgrade to Dynamic Disk dialog box d. Remove the mirror on the Missing disk. Right-click the Operating System Partition, C: in this example, on the Missing disk and select Remove Mirror.
  • Page 5 Replacing a failed hard drive e. The Mirror should now be removed from the Missing disk as show in Figure Figure 11: Mirror removed from Missing disk Recreate the Mirror on the new disk. Right-click the Volume, C: on Disk 0 in this example, and select Add Mirror as shown in Figure Figure 12: Select Add Mirror...
  • Page 6 Replacing a failed hard drive Figure 13: Add Mirror dialog box h. Repair the data volume. Right-click the data volume and select Repair Volume as shown in Figure 14. Select the new disk, Disk 1 in this example, in the Repair RAID-5 Volume dialog box as show in Figure Figure 14: Selecting Repair Volume...
  • Page 7 Replacing a failed hard drive After this procedure, the drives will need time to regenerate. Do not shut down or restart the system until the Mirroring of C: or E: is complete. The system can be shut down while the Data volume is still regenerating, but will have to be restarted once the system is running.