HP Z200 - Small Form Factor Workstation Installation Manual
Hp sata/sas hard drive and solid state drive installation
Hide thumbs
Also See for Z200 - Small Form Factor Workstation:
- Maintenance and service manual (210 pages) ,
- User manual (87 pages) ,
- Overview (54 pages)
Table of Contents
Advertisement
Quick Links
HP SATA/SAS hard drive and Solid State
Drive installation
This document describes how to install Serial ATA (SATA) and Serial Attached SCSI (SAS) hard
drives or Solid State Drives (SSD) in an internal hard drive bay. Throughout this document, all
references to hard drives include solid state drives.
Kit contents
●
A SATA or SAS hard drive or Solid State Drive (SSD)
●
Multiple SATA interface cables (each of a different length and with different connector orientation
combinations)
●
SAS-to-SATA interface adapter (included with SAS hard drives)
●
Four 6-32 guide screws
●
Installation instructions (this document)
●
Warranty information
Tools required
The following may be required to install the hard drive:
●
T-15 Torx screwdriver or flat-bladed screwdriver
Your responsibilities
You are responsible for determining whether the product is appropriate for your use and will interface
with other equipment without malfunction or damage. You are also responsible for backing up data
before installing any product and for regularly backing up data after installing the product. HP is not
liable for any damage to equipment or data loss resulting from the use of any product. To determine
the compatibility of this product with your computer or workstation, view QuickSpecs at
http://www.hp.com/go/productbulletin.
ENWW
© 2006–2010 Hewlett-Packard Development Company, L.P. Microsoft,
Windows, XP , and Windows Vista are U.S. registered trademarks of Microsoft
Corporation. Printed in the U.S.
Kit contents
1
Advertisement
Table of Contents
Related Manuals for HP Z200 - Small Form Factor Workstation
Summary of Contents for HP Z200 - Small Form Factor Workstation
-
Page 1: Drive Installation
To determine the compatibility of this product with your computer or workstation, view QuickSpecs at http://www.hp.com/go/productbulletin. © 2006–2010 Hewlett-Packard Development Company, L.P. Microsoft, Windows, XP , and Windows Vista are U.S. registered trademarks of Microsoft Corporation. Printed in the U.S. -
Page 2: Warnings And Cautions
Warnings and cautions WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of a hot surface or hot component. If this surface is contacted, the potential for injury exists. To reduce the risk of injury from a hot component, enable the surface to cool before touching. WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of an electrical shock hazard. -
Page 3: Step 1-Preparing For Component Installation
Step 1—Preparing for component installation NOTE: Computer models vary. All illustrations are examples only. Accessing the internal components of the computer If you need help preparing the computer for this installation, consult the removal and replacement procedures in the service guide for your computer at http://www.hp.com/support/ manuals. - Page 4 Remove the drive carrier from the highest empty internal hard drive bay: Open the handle at the green touch-point (1). Slide the hard drive carrier out of the bay (2). Figure 1 Removing the hard drive carrier Install the hard drive in the carrier: Position the carrier with the handle end down.
- Page 5 Slide the drive carrier firmly into the hard drive bay, rotating the handle to snap it closed. Power and data connectors are pre-installed at the back of the bay. SAS-to-SATA adapters or additional power and data connections are not required. ●...
- Page 6 Push the drive into the bay until it snaps into place. Continue with Connecting the power and data cables on page Computers that use guide screws installed in the hard drive NOTE: In some computers, such as the HP Z200 SFF, you may need to temporarily remove the optical drive to install the hard drive.
- Page 7 Connecting the power and data cables If installing a SAS hard drive, attach the SAS-to-SATA interconnect cable adapter to the SAS connector on the hard drive. The cable adapter is provided with the kit and is required only when installing a SAS hard drive. Figure 5 Install the SAS-to-SATA adapter Select the SATA interconnect cable from the kit that best fits the hardware configuration of your...
-
Page 8: Step 4-Reassembling The Computer
Step 4—Reassembling the computer Reinstall the card support, if applicable. Reinstall the side access panel. Reconnect power to the computer and all external devices. Restore power to the computer and all external devices. Step 5—Configuring the computer When powering up the computer after installation, a new hard drive identifies itself as un-initialized storage.