Related Manuals for Lenovo 828747F
Summary of Contents for Lenovo 828747F
- Page 1 User Guide Types 8287 8296 8299 8327 8340 Types 8343 8381 8782 8783 8784 Types 8785 8786 8788...
- Page 3 User Guide Types 8287 8296 8299 8327 8340 Types 8343 8381 8782 8783 8784 Types 8785 8786 8788...
- Page 4 RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to the GSA ADP Schedule contract with Lenovo Group Limited, if any, or the standard terms of this commercial license, or if the agency is unable to accept this Program under these terms, then we provide this Program under the provisions set forth in Commercial Computer Software–Restricted Rights at FAR 52.227-19, when applicable, or under Rights in...
-
Page 5: Table Of Contents
. 24 Installing security features . . 24 Index ....51 Identifying security locks . . 25 © Lenovo 2005, 2006. Portions © IBM Corp. 2005, 2006. - Page 6 User Guide...
-
Page 7: Important Safety Information
In the unlikely event that you notice any of the conditions listed below, or if you have any safety concerns with your product, stop using the product and unplug it from the power source and telecommunication lines until you can © Lenovo 2005, 2006. Portions © IBM Corp. 2005, 2006. -
Page 8: General Safety Guidelines
Note: If you notice these conditions with a product (such as an extension cord) that is not manufactured for or by Lenovo, stop using that product until you can contact the product manufacturer for further instructions, or until you get a suitable replacement. -
Page 9: Power Cords And Power Adapters
Danger Hazardous moving parts. Keep fingers and other body parts away. Attention Before replacing any CRUs, turn off the computer and wait three to five minutes to let the computer cool before opening the cover. Power cords and power adapters Use only the power cords and power adapters supplied by the product manufacturer. -
Page 10: Extension Cords And Related Devices
In addition, many mobile products, such as notebook computers, utilize a rechargeable battery pack to provide system power when in portable mode. Batteries supplied by Lenovo for use with your product have been tested for compatibility and should only be replaced with approved parts. -
Page 11: Heat And Product Ventilation
Batteries can degrade when they are left unused for long periods of time. For some rechargeable batteries (particularly Lithium Ion batteries), leaving a battery unused in a discharged state could increase the risk of a battery short circuit, which could shorten the life of the battery and can also pose a safety hazard. -
Page 12: Additional Safety Information
v Always store CD/DVD discs out of direct sunlight and away from direct heat sources v Remove CD/DVD discs from the computer when not in use v Do not bend or flex CD/DVD discs, or force them into the computer or their packaging v Check CD/DVD discs for cracks before each use. -
Page 13: Modem Safety Information
v Heat to more than 100°C (212°F) v Repair or disassemble Dispose of the battery as required by local ordinances or regulations. Modem safety information Caution To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. To reduce the risk of fire, electrical shock, or injury when using telephone equipment, always follow basic safety precautions, such as: v Never install telephone wiring during a lightning storm. -
Page 14: Power Supply Statement
Danger Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Power supply statement Never remove the cover on a power supply or any part that has the following label attached. -
Page 15: Overview
Troubleshooting information v Parts information v Downloads and drivers v Links to other useful sources of information v Support phone list To access this information, point your browser to: http://www.lenovo.com/support/. xiii © Lenovo 2005, 2006. Portions © IBM Corp. 2005, 2006. - Page 16 User Guide...
-
Page 17: Chapter 1. Installing Options
Microprocessor (varies by model type) ® ® v Intel Pentium D processor with HyperThreading Technology v Intel Pentium D processor ® v Intel Celeron D processor v Internal cache (size varies by model type) © Lenovo 2005, 2006. Portions © IBM Corp. 2005, 2006. - Page 18 Memory v Support for four double data rate (DDR2) dual inline memory modules (DIMMs) v 512KB flash memory for system programs Internal drives v 3.5-inch, slim, 1.44 MB diskette drive v Serial Advanced Technology Attachment (SATA) internal hard disk drive v Optical drive (some models) Video subsystem v An integrated graphics controller for a Video Graphics Array (VGA) monitor...
- Page 19 1. The operating systems listed here are being certified or tested for compatibility at the time this publication goes to press. Additional operating systems might be identified by Lenovo as compatible with your computer following the publication of this booklet. Corrections and additions to this list are subject to change. To determine if an operating system has been certified or tested for compatibility, check the Web site of the operating system vendor.
-
Page 20: Specifications
Maximum altitude: 914 m (3000 ft) values, please refer to the latest copy of this document Note: The maximum altitude, 914 m (3000 ft), is which is available at http://www.lenovo.com/support. the maximum altitude at which the specified air temperatures apply. At higher altitudes, the maximum air temperatures are lower than those specified. -
Page 21: Available Options
Within the United States, call 1-800-426-2968, your Lenovo reseller, or Lenovo marketing representative. v Within Canada, call 1-800-565-3344 or 1-800-426-2968. v Outside the United States and Canada, contact your Lenovo reseller, or Lenovo marketing representative. Tools required To install some options in your computer, you might need a flat-blade or Phillips screwdriver. -
Page 22: Handling Static-Sensitive Devices
Handling static-sensitive devices Static electricity, although harmless to you, can seriously damage computer components and options. When you add an option, do not open the static-protective package containing the option until you are instructed to do so. When you handle options and other computer components, take these precautions to avoid static electricity damage: v Limit your movement. -
Page 23: Locating The Connectors On The Front Of Your Computer
Locating the connectors on the front of your computer The following illustration shows the locations of the connectors on the front of the computer. Note: Not all computer models will have the following connectors. IEEE 1394 connector (some models) Microphone connector USB connector Headphone connector USB connector... -
Page 24: Locating The Connectors On The Rear Of Your Computer
Locating the connectors on the rear of your computer The rear connector locations are different depending on your machine type. Machine types 8287, 8296, 8299, 8327, 8340, 8343, and 8381 The following illustration shows the locations of the connectors on the rear of the computer. - Page 25 Machine types 8782, 8783, 8784,8785,8786, and 8788 The following illustration shows the locations of the connectors on the rear of the computer. Power supply diagnostic LEDs USB connectors (2) Voltage selection switch Ethernet connector Power connector Microphone connector Standard mouse connector Audio line out connector Standard keyboard connector Audio line in connector...
-
Page 26: Connector Descriptions
Connector descriptions The following describes the use of the connectors on the front and rear of your computer. Some connectors on the rear of the computer are color-coded to help you determine where to connect the cables on your computer. Connector Description Audio line in connector... -
Page 27: Obtaining Device Drivers
Obtaining device drivers You can obtain device drivers for operating systems that are not preinstalled at http://www.lenovo.com/support/ on the World Wide Web. Installation instructions are provided in README files with the device-driver files. Removing the cover Important Read “Important safety information” on page v and “Handling static-sensitive devices”... -
Page 28: Pivoting Or Removing The Optional Hard Disk Drive Mounting Bracket
6. Some models have an optional hard disk drive mounting bracket 1 installed. When this bracket is installed, access to some of the components inside the chassis is restricted. Note: There appears to be two drive bays in the bracket. However, due to thermal restrictions, only the bay 2 at the rear of the chassis can be used to install a hard disk drive. - Page 29 If it is necessary to remove the optional hard disk drive mounting bracket, disconnect the cables attached to the optional hard disk drive, remove the two screws, and lift the bracket out of the chassis. Chapter 1. Installing options...
-
Page 30: Locating Components
Locating components The following illustration will help you locate the various components in your computer. Optical drive Memory modules Power supply PCI-express (PCI-e) adapter connector PCI adapter card System board Hard disk drive Internal speaker Diskette drive User Guide... -
Page 31: Identifying Parts On The System Board
Identifying parts on the system board The system board (sometimes called the planar or motherboard) is the main circuit board in your computer. It provides basic computer functions and supports a variety of devices that are factory-installed or that you can install later. The system board connector locations are different depending on your machine type. -
Page 32: Machine Types 8782, 8783, 8784, 8785, 8786, And 8788
Machine types 8782, 8783, 8784, 8785, 8786, and 8788 The following illustration shows the locations of parts on the system board. 12V power connector PCI adapter connector Memory connector 2 PCI adapter connector Memory connector 1 Diskette drive connector Power supply connector Front panel connector Serial connector (COM 2) USB connector (Front panel) -
Page 33: Installing Memory
Installing memory Your computer has four connectors for installing dual inline memory modules (DIMMs). When installing DDR2 type memory modules, the following rules apply: v Use 1.8 V, 240-pin double data rate 2 synchronous dynamic random access memory (DDR2 SDRAM). v Use 256 MB, 512 MB, 1.0 GB, or 2.0 GB memory modules in any combination that provide up to a maximum of 4.0 GB of system memory. -
Page 34: Installing Adapters
Installing adapters This section provides information and instructions for installing and removing adapters. Your computer has two expansion connectors for PCI adapters, one for a PCI Express (x1) adapter, and one for a PCI Express (x16) adapter. To install an adapter: 1. -
Page 35: Installing Internal Drives
What to do next v To work with another option, go to the appropriate section. v To complete the installation, go to “Replacing the cover and connecting the cables” on page 29. Installing internal drives This section provides information and instructions for installing and removing internal drives. - Page 36 The following illustration shows the locations of the drive bays. The following list describes the types and size of drives you can install in each bay: 1 Bay 1 - Maximum height: 43.0 mm (1.7 in.) v Optical drive such as CD drive or DVD drive (preinstalled in some models) v 5.25-inch hard disk drive v 3.5-inch hard disk drive (requires a...
-
Page 37: Installing A Drive In Bay 1 Or Bay 2
Installing a drive in bay 1 or bay 2 To install a drive in bay 1 or bay 2, follow these steps: 1. Remove the cover. See “Removing the cover” on page 11. 2. Remove the front bezel by pressing downward on the plastic tabs 1 and pulling the bezel as shown. - Page 38 5. If you are installing any type of drive other than a serial ATA hard disk drive, make sure the drive that you are installing is set correctly as either a master or a slave device. Note: A serial ATA hard disk drive does not need to be set as either a master or a slave device.
-
Page 39: Connecting Drives
Connecting drives The steps to connect a drive are different depending on the type of drive. Use one of the following procedures for your drive connection. Connecting the first optical drive 1. The drive requires two cables; a power cable that connects to the power supply and a signal cable that connects to the system board. -
Page 40: Connecting A Serial Ata Hard Disk Drive
Connecting a serial ATA hard disk drive A serial hard disk drive can be connected to any available SATA IDE connector. 1. Locate the signal cable that comes with the new drive. 2. Locate an available SATA IDE connector on the system board. See “Identifying parts on the system board”... -
Page 41: Identifying Security Locks
Identifying security locks The following illustration shows the locations of the security locks on the rear of the computer. 1 Padlock loop 2 Integrated cable lock Chapter 1. Installing options... -
Page 42: Padlock
Padlock Your computer is equipped with a padlock loop such that the cover cannot be removed when a padlock is installed. User Guide... -
Page 43: Integrated Cable Lock
This is the same type of lock used with many laptop computers. You can order a cable lock directly from Lenovo. Go to http://www.lenovo.com/think and click Upgrades and accessories −> Security. -
Page 44: Erasing A Lost Or Forgotten Password (Clearing Cmos)
configuration information (including passwords) are lost. An error message is displayed when you turn on the computer. Refer to “Lithium battery notice” on page x for information about replacing and disposing of the battery. To change the battery: 1. Turn off the computer and all attached devices. 2. -
Page 45: Replacing The Cover And Connecting The Cables
4. Move the jumper from the standard position (pins 1 and 2) to the maintenance or configure position (pins 2 and 3). 5. Replace the cover and connect the power cord. See “Replacing the cover and connecting the cables.” 6. Restart the computer, leave it on for approximately ten seconds. Turn off the computer by holding the power switch for approximately five seconds. - Page 46 User Guide...
-
Page 47: Chapter 2. Using The Setup Utility Program
– Contain at least one alphabetic character, one numeric character, and one symbol – Have at least one symbol in the second through sixth positions – Not be your name or your user name © Lenovo 2005, 2006. Portions © IBM Corp. 2005, 2006. -
Page 48: User Password
– Not be a common word or a common name – Be significantly different from your previous password Note: If you type an incorrect password, you will see an error message. If you type an incorrect password three consecutive times, you must turn the computer off and start again. -
Page 49: Setting, Changing, And Deleting A Password
Setting, changing, and deleting a password To set, change, or delete a password, do the following: Note: A password can be any combination of up to twelve characters (A- Z, a-z, and 0-9). See “Password considerations” on page 31 for more information. 1. -
Page 50: Using Security Profile By Device
Using Security Profile by Device Security Profile by Device is used to enable or disable user access to the following devices: IDE controller When this feature is set to Disable, all devices connected to the IDE controller (such as hard disk drives or the CD-ROM drive) are disabled and will not be displayed in the system configuration. -
Page 51: Exiting From The Setup Utility Program
5. Press F10 to save and exit from the Setup Utility program. If you have changed these settings and want to return to the default settings, select Load Default Settings on the Exit menu. Exiting from the Setup Utility program When you finish viewing or changing settings, press Esc to return to the Setup Utility program menu (you might have to press Esc several times). - Page 52 User Guide...
-
Page 53: Appendix A. Updating System Programs
8. Follow the instructions on the screen to complete the update. Updating (flashing) BIOS from your operating system Note: Due to constant improvements being made to the Lenovo Web site, Web page content (including the links referenced in the following procedure) is subject to change. -
Page 54: Recovering From A Post/Bios Update Failure
1. From your browser, type http://www.lenovo.com/support in the address field and press Enter. 2. Locate the Downloadable files for your machine type as follows: a. In the Use Quick path field, type in your machine type and click Go. b. Under Browse by product, click Continue. -
Page 55: Appendix B. Cleaning The Mouse
1. Turn off your computer. 2. Turn the mouse over, with the top side down, and look carefully at the bottom. Twist the retainer ring 1 to the unlocked position to remove the ball. © Lenovo 2005, 2006. Portions © IBM Corp. 2005, 2006. - Page 56 3. Place your hand over the retainer ring and ball 2 , and then turn the mouse over, top side up, so that the retainer ring and ball fall out into your hand. 4. Wash the ball in warm, soapy water then dry it with a clean cloth. Blow air carefully into the ball cage 4 to dislodge dust and lint.
-
Page 57: Appendix C. Manual Modem Commands
(n=0-3) stored in the modem non-volatile memory. Commands are not echoed Commands are echoed Escape Characters - Switch from Data Mode to Command Mode (T.I.E.S. Command) Force modem on-hook (hang up) © Lenovo 2005, 2006. Portions © IBM Corp. 2005, 2006. - Page 58 Command Function Force modem off-hook (make busy) Note: H1 command is not supported for Italy Display product-identification code Factory ROM checksum test Internal memory test Firmware ID Reserved ID Low speaker volume Low speaker volume Medium speaker volume High speaker volume Internal speaker off Internal speaker on until carrier detected Internal speaker always on...
-
Page 59: Extended At Commands
Extended AT commands Command Function &C_ &C0 Force Carrier Detect Signal High (ON) &C1 Turn on CD when remote carrier is present &D0 &D_ Modem ignores the DTR signal &D1 Modem returns to Command Mode after DTR toggle &D2 Modem hangs up, returns to the Command Mode after DTR toggle &D3 Resets modem after DTR toggle... -
Page 60: Mnp/V.42/V.42Bis/V.44 Commands
Command Function &V1 Display Last Connection Statistics &W_ &W0 Stores the active profile as Profile 0 &W1 Stores the active profile as Profile 1 Disable auto-retrain Enable auto-retrain +MS? Displays the current Select Modulation settings +MS=? Displays a list of supported Select Modulation options +MS=a,b,c,e,f Select modulation where: a=0, 1, 2, 3, 9, 10, 11,... -
Page 61: Fax Class 1 Commands
Fax Class 1 commands +FAE=n Data/Fax Auto Answer +FCLASS=n Service Class +FRH=n Receive data with HDLC framing Receive data +FRM=n +FRS=n Receive silence +FTH=n Transmit data with HDLC framing +FTM=n Transmit data +FTS=n Stop transmission and wait Fax Class 2 commands +FCLASS=n Services class. -
Page 62: Voice Commands
+FPHCTO Phase C time out. +FPOLL Indicates polling request. +FPTS: Page transfer status. +FPTS= Page transfer status. +FREV? Identify revision. +FSPT Enable polling. +FTSI: Report the transmit station ID. Voice commands Select Baud Rate #BDR #CID Enable Caller ID detection and reporting format Select Data, Fax or Voice/Audio #CLS #MDL? - Page 63 Attention Switzerland User: If your Swisscom phone line does not have Taxsignal switched OFF, modem function may be impaired. The impairment may be resolved by a filter with the following specifications: Telekom PTT SCR-BE Taximpulssperrfilter-12kHz PTT Art. 444.112.7 Bakom 93.0291.Z.N Appendix C.
- Page 64 User Guide...
-
Page 65: Appendix D. Notices
Web sites. The materials at those Web sites are not part of the materials for this Lenovo product, and use of those Web sites is at your own risk. -
Page 66: Television Output Notice
Macrovision Corporation. Reverse engineering or disassembly is prohibited. Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo ThinkCentre ThinkVantage... -
Page 67: Index
5 noise level 4 removable media 5 specifications 19 obtaining device drivers 11 environment, operating 4 options 5 Ethernet connector 10 available 4 external 5 internal 5 overview xiii © Lenovo 2005, 2006. Portions © IBM Corp. 2005, 2006. - Page 68 padlock loop 26 parallel connector 10 password administrator 32 considerations 31 erasing 28 lost or forgotten 28 setting, changing, deleting 33 strong 31 user 32 physcial specifications 4 physical specifications 4 power Advanced Configuration and Power Interface (ACPI) support 3 Advanced Power Management support 3 productivity center 28 recovering from a POST/BIOS update failure 38...
- Page 70 Part Number: 41D4461 Printed in USA (1P) P/N: 41D4461...