Appendix
Are the filter settings appropriate?
Excessively high filter resonance settings can cause distortion.
[VOICE] [EDIT] Element/Key selection [F3] FILTER
[PERFORM] [EDIT] Part selection [F4] TONE [SF1] FILTER
[SONG]/[PATTERN] [MIXING] [EDIT] Part selection [F4] TONE [SF1] FILTER
[SONG]/[PATTERN] [UTILITY] [F2] SEQ [SF2] FILTER
Are any of the following volume parameters set so high that clipping is occurring?
[UTILITY] [F1] GENERAL [SF1] TG "Volume"
[VOICE] [EDIT] [COMMON] [F2] OUTPUT Volume
[VOICE] [EDIT] Element/Key selection [F4] AMP [SF1] LVL/PAN "Level"
[PERFORM] [EDIT] [COMMON] [F2] OUT/MFX [SF1] OUT "Volume"
[PERFORM] [EDIT] Part selection [F2] OUTPUT [SF1] VOL/PAN "Volume"
[SONG]/[PATTERN] [MIXING] [EDIT] Part selection [F2] OUTPUT [SF1] VOL/PAN "Volume"
Sound is cut off.
Is the entire amount of notes played (via your keyboard playback and Song/Pattern/Arpeggio playback) exceeding the maximum
polyphony of this instrument?
Only one note sounds at a time.
When this situation occurs, the Mono/Poly parameter in the current mode is set to "mono." If you wish to play chords, set this parameter
to "poly."
[VOICE] [F4] PORTA "Mono/Poly"
[PERFORM] [EDIT] Part selection [F1] VOICE [SF2] MODE "Mono/Poly"
[SONG]/[PATTERN] [MIXING] [EDIT] Part selection [F1] VOICE [SF2] MODE "Mono/Poly"
Pitch or intervals are wrong.
Is the Master Tune parameter in the Utility mode set to a value other than "0"?
[UTILITY] [F1] GENERAL [SF1] TG "Tune"
Is the Note Shift parameter in the Utility mode set to a value other than "0"?
[UTILITY] [F1] GENERAL [SF1] TG "NoteShift"
When the Voice produces a wrong pitch, is the appropriate tuning system selected from Micro Tuning parameter in the Voice Edit
mode?
[VOICE] [EDIT] [COMMON] [F1] GENERAL [SF2] PLY MODE "M. Tuning No."
When the Voice produces a wrong pitch, is the LFO Pitch Modulation Depth in the Voice Edit mode set too high?
[VOICE] [EDIT] Element/Key selection [F5] LFO "PMod"
When the Performance/Song/Pattern produces a wrong pitch, are the Note Shift and Detune parameters of each Part set to a value other
than "0"?
[PERFORM] [EDIT] Part selection [F4] TONE [SF1] TUNE
[SONG]/[PATTERN] [MIXING] [EDIT] Part selection [F4] TONE [SF1] TUNE
When the Song/Pattern playback produces a wrong pitch, is the Note Offset parameter in the Groove display set to a value other than "0"?
[SONG]/[PATTERN] [F2] GROOVE "NOTE OFST"
No effect is applied.
Check the on/off status of the EFFECT [INSERTION]/[SYSTEM]/[MASTER] button.
Is the Reverb Send or Chorus Send set to a value other than "0"?
[VOICE] [EDIT] [COMMON] [F2] OUTPUT "ChoSend" / "RevSend"
[PERFORM] [EDIT] [COMMON] [F2] OUT/MFX [SF1] OUT "ChoSend" / "RevSend"
[SONG]/[PATTERN] [MIXING] [EDIT] Part selection [F2] OUTPUT [SF1] VOL/PAN "ChoSend" / "RevSend"
Have any or all of the Elements' Insertion Effect Output parameters been set to "thru" in the effect setting display in the Voice Edit
mode?
[VOICE] [F6] EFFECT [SF1] CONNECT "EL: OUT 1-8"
64
MOX6/MOX8 Owner's Manual