Advertisement
6. Control Panel and Program Description
Press the "Night Wash" button, the icon will light
It displays washing time,
Press the "Speed"
up,indicating this function is selected.
remaining washing time,
button to select
After started,all buzzer sound is canceled(except
set speed, set
spinning speed.
error alarm sound),the maximum spin speed is
temperature, child lock
The maximum
800 rum.
state, times of extra rinse,
allowable spinning
If "Night Wash" function was selected and the
door lock state, washing
speed varies with
maximum spin speed higher than 800 rpm, the
progress and alarm
programs.
machine will adjust it to 600 rpm automatically.
message, etc.
All progarm can select "Night Wash"function.
"Night Wash"
"Speed" selection button
I
b
t t u
n o
D
p s i
y a l
c s
e r
n e
Press the "Speed up" button, the icon
will light up, indicating this function is
selected; this function may reduce the
water and power consumption of
Night Wash
Speed
washing.
This function is available before a
Speed Up
Temp.
washing program starts and may reduce
the main wash time or a time of rinse for
some programs.
Delay
Extra Rinse
Strong
Anti-crease
This function is not available for the
"Spin", "Dry", "Iron", "Air-wash",
"Self-clean" and "Quick" programs.
"
e D
y a l
b "
t t u
n o
"
x E
a r t
n i r
e s
b "
t t u
n o
Press the "Delay" button, its indicator will light up, indicating this
Press the "Extra rinse" button, its indicator will
Press the "Strong" button to select or cancel the function of
function is selected. The delay time (0.5-24h) increases by 30min
intensive washing
light up, indicating this function is selected.
This function is to increase wanshing time,times of rinse and
each press of "Delay" button. The time will change continuously if
You may increase the times of rinse (at most
spinning time of the main wash stage of the selected program.
you press and hold this button until you release it.
three times) before softening. "P--1" shown on
When the"Strong"indicator lights up,it means this function is
The delay time is the end time of washing. For example, 6:00
the display screen means the washer will carry
seclected.
means the washing ends after 6 hours (the delay time must be
out one more time of rinse.
This function is not available for the "Rinse", "Spin" and "drain"
longer than the program's running time).
This function is not available for the "Spin",
programs.
This function is not available for the "Spin", "Drain" programs.
"Drain" programs.
"Strong" and "Speed Up" are not available to select together.
"Anti-crease" and "Delay" are not available to select together.
7. Display Screen
Numerical display area (after power-on, the time of last washing
program is displayed in this area; it displays various preset codes,
e.g.
is displayed at the time of trouble alarm)
"Door lock" icon
"Child lock" icon
"Night wash" icon
Spinning speed
Program progress bar
"Speed up" icon
Heating temperature
"Prewash" icon "Main wash"
"Rinse"
"Spin" icon
icon
icon
Note: The time shown on the display screen is only for reference and may be slightly different from actual time;
When the "Prewash" program is selected, its icon will light up;
When the selected program runs to the main wash, rinse or spin stage, the corresponding icon on the
display screen will flash.
Press the "Temp." button
• Press the"Strat/Pause" button,the washer will start and
Select the
the indicators will keeps on,if this button is pressed when
to select heating
desired program
the washer is in operation,the washer will pause and the
temperature (--, 30, 40,
indicator will flash.
by turning this
If not press the"Strat/Pause"button after switch on power
50, 60, 90). The
knob.
and satisfy the door open condition,press this button
maximum allowable
about 2 seconds can open the door.
After turning on
heating temperature
•
This machine with auto-weight function,perss "Power "
the washer, it
button and the door will open automatically,put in laundry
varies with programs.
automatically
and close the door.The screen display
,press
"- -" in the temperature
selects the
"Strat/Pause" button,the washer will finish the weight
display area indicates
automatically about 2 minutes later and select proper
program of last
program,this function save water,power and time
non-heated washing.
washing.
effectively.
"Temp." selection button
Program knob
"Start/Pause"
I
b
t t u
n o
Press the "Power" button to
switch on the washer. Press
this button again and hold it
S-D Inverter
Quick
Heavy
for 2s to switch it off.
Wool
Underwear
After switching on the
Synthetic
Rinse
washer, if any button is not
Power
pressed within 5min, it will
Cotton
Spin
automatically turn off.
6.0kg
Start
Prewash
Drain
Pause
HW60-B12866NZP
Press and hold 2 seconds
to set door unlocked
"Strong" button
"Anti-crease" button
• Press "Anti-crease" button to start up/shut down the
crease-resistant and soak function.
•When the process runs to the last rinse, the washing
machine is not going to drain, clothes will be soaked in
water, and the soak icon flashes, the remain time not
decreasing. If you need to dry the clothes, you can
press "Anti-crease" button or "start /pause" button,then
the icon will be off to cancel this function,and the
washing machine continue to work.
• This feature and the "delay"button can not be chose at
the same time. Also this feature is ineffective in the
"Spin,Drain"process.
8. Other functions
Function
Eccentric protection
When spinning, if the clothes are not evenly distributed, the washer will fluff out
and redistribute the clothes and continue spinning after the clothes distribution
becomes even. If the clothes distribution does not become even within the
Function
Power-down memory
specified time, the washer will not spin to avoid abnormal vibration. In this case,
With the power-down memory function, the washer can
please check the clothes for intertwist and rearrange them, then select "Spin"
memorize the program's running state in case of power
program to spin the clothes. When there are few clothes, the washer may not spin
failure or loose plug during washing and continue the
due to eccentric protection. In this case, you can put more clothes into the washer
formerly selected program after the power supply resumes.
and make them evenly distributed, then continue spinning. In addition, it is normal
that the program time will prolong because the washer rearranges and fluffs out
the clothes.
Function
Cancel or reselect a program during washing
(1) To cancel the running program, just turn off the washer;
to reselect a program, turn it on again.
(2) To select any additional function when a program is
Function
Silencing function
running, just press the "Start/Pause" button, then select your
Select the "Spin" program, simultaneously press the "Delay" and "Extra rinse"
desired additional function and finally press the
buttons and hold them for 3 seconds, the beep of all the programs (excluding the
"Start/Pause" again.
alarm sound) will be silenced and the display screen will show "
Simultaneously press the two buttons and hold them for 3 seconds again, the
beep of all the programs will resume and the display screen will show "
Note:
The above operations should be made when the child lock is
not activated.
The method (2) is only available for several function buttons.
9. Fault Clearance
The following phenomena are not necessarily faults of the washer. Please check against the following table before calling for repair.
If any fault actually exists, please contact our After-sales Service Department and do not repair by yourself. Please pull out the power plug before check.
Programs Guide
S
a t
e t
P
e h
o n
m
n e
n o
o S
i t u l
n o
For prewashing
Prewash
relatively dirty
There is a little water in
cotton/linen fabrics
It is normal; the water is the remaining
the drain pipe and
water of factory inspection
washer when using the
Cotton
For washing cotton
washer for the first time
fabrics
Check whether power failure or abnormal
power supply occurs
For washing
Synthetic
Check whether the power plug is firmly
chemical fiber
inserted into the socket
Check whether the fuse of power supply or the
fabrics
The washer does
current breaker is in good condition
not operate
Wool
For washing wool
Check whether the "Power" switch is turned on
Check whether the water tap is turned on
fabrics
Check whether the "Delay" function is selected
Check whether the "Start/Pause" button is
Quick
For washing slightly dirty
pressed
cotton and chemical
Check whether the "Child lock" function is
fiber fabrics
Buttons cannot be
selected
operated
After starting, to select other programs,
Sport Wash
For washing sport
please press the "Start/Pause" button and
wear
then operate
Check whether the water tap is in proper shape
Hand wash
For washing the not too
Water leakage occurs
Check whether the water inlet pipe joint is
dirty cotton abrics or
at the water tap
installed in place
chemical fiber fabrics
Check whether the water tap is damaged
Check whether the water tap is turned on and
For washing Jean clothes
Heavy
whether water supply cut-off occurs
and big fabrics
Check whether the water inlet valve is clogged (if
No water inflow or
necessary, clean the valve)
Check whether the water tap and water inlet pipe
slow water inflow
Underwear
For washing contton
are frozen
Check whether the "Delay" program is selected
underwear or children`s
Check whether the "Start/Pause" button is pressed
Check whether the water inlet pipe is bent
clothes
Check whether the water pressure is too low
For washing the clothes
Rinse
Water feeding and water
Check whether the height of drain pipe
only
orifice is within the range of 80cm~100cm
drainage occurs at the
same time
Check whether the drain pipe orifice is
For spinning the clothes
immersed in the water
Spin
only
Check whether the washer inclines or shakes
For drainning the water
Drain
Check whether there are foreign bodies such
as coins and zippers in the washer
only
Abnormal noise
Check whether the noise is from the buttons
and zippers of washing
Check whether the noise is from the draining
pump or motor in normal operation
Function
Memory Backup
The washer can memory the program you slected last time and your washing
custom,just need to press the "Start/Pause" button to start the washing,
no need to set the program again.Of course, you can adjust the program
before start.
Function
Child Lock
After start, press the "Delay"and the "Start/Pause" button for about 3 seconds to
activate the child lock, after the child lock was activated, all buttons are useless.
".
After the child lock was activated, press the "Delay" and "Start/Pause" button
for about 3 seconds to cancel it.
".
After the child lock was activated,Power button is effective.
S
a t
e t
P
e h
o n
m
n e
n o
o S
i t u l
n o
D
p s i
y a l
d e
o c
e d
o C
e d
m
a e
i n
The washer is in automatic
Check whether the type and dosage of
weighing state
Poor washing effect
detergent are suitable
Check whether the selected program is
correct
The remaining washing time is
one hour and sixteen minutes
Check whether the clothes weight
Forceless washing
exceeds the washer's rated washing
The spinning speed is set
at 800 rpm
capacity
Check whether sudden power failure
The whole program ends
Stop operation
or water supply cut-off occurs
during washing
Check whether the "Start/Pause"
button is pressed
Abnormal door locking or
unclosed door
The washer's program is set with
water discharge time and the
spinning starts after a period of time
No spinning
Drainage fault
Check whether the clothes intertwist
Check whether too much washing
powder was added
Temperature sensor fault
Check whether the washer is washing
Excessively long
a single piece of clothing, e.g. woolen
spinning time
sweater. If so, it is normal
Heating fault
Check whether all the fixing bolts for
transport are removed
Check whether the washer is level (the
Loud noise when spinning
washer can be leveled by adjusting the feet)
Vibration and
Check whether the clothes intertwist
displacement
Check whether the washer collides with
Abnormal water inflow
other objects
Check whether there are foreign bodies in
the washer
The clothes are not
spun dry after finishing
The spinning effect varies with the
type of clothes
the "Spin" program
Check whether it is for eccentric
protection with few clothes
The motor stops running
Check whether the drain pipe is bent,
No water discharge or
clogged or frozen
slow water discharge
Check whether the drain pipe orifice is
The water level exceeds
100cm higher than the floor
alarm level
Check whether the filter is clogged
The control panel is
partially hot
It is normal that electronic
components are slightly hot
Water level sensor fault
The washing does not
The clothes distribution becomes
end after the preset
imbalanced during washing
delay time
Poor water feeding/drainage
Uneven clothes distribution
conditions result in a longer time
while spinning
10.Cleaning/Maintenance
Please pull out the power plug from the socket before
cleaning and maintenance.
Filter cleaning (once a month as recommended)
Fig. 1
(1) After draining the water in the washer, open the filter door by pressing it
down with a flat head screwdriver or a similar tool through the square hole
above the filter door (as shown in Fig. 1).
(2) Hold the plastic pipe plug to pull out the waste pipe, prepare a water
Filter
container, remove the plastic plug of waste pipe to drain the remaining
water into the container (as shown in Fig. 2), replace the plastic plug onto
Fig. 2
the waste pipe, and finally clamp the waste pipe in original position.
(3) Anticlockwise screw out the filter. It is normal that a little water flows out
at this time (as shown in Fig. 3).
Waste pipe
(4) Rinse with clean water (as shown in Fig. 4).
(5) Insert the filter after aligning its convex with the groove of draining pipe,
Waste pipe plug
Water container
then clockwise tighten it (as shown in Fig. 5), and finally close the filter door.
Fig. 3
Fig. 4
g n
o S
i t u l
n o
D
p s i
y a l
d e
o c
e d
o C
e d
m
a e
i n
g n
o S
i t u l
n o
Communication fault
Please ask for repair
Being inconsistent with the
conditions for door opening,
it is not allowed to unlock
the door
Note:
It is normal that the washer discharges water when
or
occurs.
Close the door; if the problem
remains, please ask for repair
Clean the draining pump filter
and check whether the drain
pipe is clogged; if the problem
remains, please ask for repair
Please ask for repair
Warm tips
To add clothes during washing or to take out clothes
after extended power failure, make sure that the
Pull wire
water level in the drum is properly below the lower
Please ask for repair
edge of sight glass, the water temperature is below
Shut down the washer and
remove the problem. • • Check
the drain pipe from its holder and put it down until no
whether the water tap is turned on,
water is drained from the drain pipe, afterwards put
whether the water pressure is too
back the drain pipe. Open the filter door at the bottom
low, whether water supply cut-off
occurs; • • Check whether the
of washer, and you will see a pull wire. Take out the
water inlet valve is clogged
pull wire and gently pull it downwards until you hear a
(please clean it); if the problem
low sound, the door will open, now you can add or
remains, please ask for repair
take out the clothes. Afterwards, reset the pull wire
and filter door.
Please ask for repair
Note:
Never perform the above operations when the washer is running.
The washer automatically
removes this problem; if the
problem remains, please
ask for repair
The washer contains recyclable materials. Please properly dispose of them to protect
the environment.
Adding a proper amount of softener may make the clothes soft, eliminate sticking arising
Please ask for repair
from static electricity and make the clothes easier to be ironed. Excessive soften may
damage synthetic fiber. Please refer to its instructions for correct dosage of softener.
Take out and fluff out the
clothes; if the problem
remains, please ask for repair
Cleaning of a distributor box
To clean a distributor box, pull it out, gently
press it down and continue to pull it out (as
shown in the figure on the right), remove it,
rinse it with water and reinstall it in place.
Cleaning of the filter screen of water inlet valve
Frequently clean the water inlet pipe joint and
water inlet
the filter screen of water inlet valve to prevent
valve joint
them from being clogged by impurities (as
shown in the figure on the right)
Note:
Please clean the filter screen of water
inlet valve as shown in the figures below.
Note:
The filter must be
tightened to avoid
• • Reinstall the filter
Fig. 5
• • Take out the filter screen • • Wash the filter screen
water leakage.
screen in place
Advertisement
