Handling drives Drives are fragile computer components that must be handled with care. Refer to the following cautions before handling drives. Additional cautions are included with the procedures to which they apply. CAUTION: To reduce the risk of damage to the computer, damage to a drive, or loss of information, observe these precautions: Before you move a computer that is connected to an external hard drive, initiate Suspend and allow the screen to clear, or properly disconnect the external hard drive.
Using an optical drive Your computer includes an optical drive that expands the functionality of the computer. Identify what kind of device is installed in your computer to see its capabilities. The optical drive allows you to read data discs, play music, and watch movies. If your computer includes a Blu-ray Disc, also known as BD, drive, then you can also watch high-definition video from disc.
Using optical discs An optical drive, such as a DVD-ROM drive, supports optical discs (CDs and DVDs). These discs store information, such as music, photos, and movies. DVDs have a higher storage capacity than CDs. Your optical drive can read standard CD and DVD discs. If your optical drive is a Blu-ray Disc ROM drive, it can also read Blu-ray discs (BDs).
Selecting the right disc (CDs, DVDs, and BDs) An optical drive supports optical discs (CDs, DVDs, and BDs). CDs, used to store digital data, are also used for commercial audio recordings and are convenient for your personal storage needs. DVDs and BDs are used primarily for movies, software, and data backup purposes.
Blu-ray Discs (BD) BD is a high-density optical disc format for the storage of digital information, including high-definition video. A single-layer Blu-ray Disc can store 25 GB, over 5 times the storage capacity of a single-layer DVD at 4.7 GB. A dual-layer Blu-ray Disc can store 50 GB, almost 6 times the storage capacity of a dual-layer DVD at 8.5 GB.
Playing a CD, DVD, or BD Turn on the computer. Press the release button (1) on the drive bezel to release the disc tray. Pull out the tray (2). Hold the disc by the edges to avoid touching the flat surfaces and position the disc label-side up over the tray spindle.
Observing the copyright warning It is a criminal offense, under applicable copyright laws, to make unauthorized copies of copyright- protected material, including computer programs, films, broadcasts, and sound recordings. Do not use this computer for such purposes. CAUTION: To prevent loss of information or damage to a disc, observe the following guidelines: Before writing to a disc, connect the computer to a reliable external power source.
Copying or creating a CD or DVD Select Computer > More Applications, and access Brasero. In the left pane, click Disc copy. Insert the disc you want to copy into the optical drive. Follow on-screen instructions to copy or create a CD or DVD. Chapter 2 Using an optical drive...
Removing a CD, DVD, or BD Press the release button (1) on the drive bezel to release the disc tray, and then gently pull out the tray (2) until it stops. Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer edges of the disc.
The optical disc tray does not open for removal of a CD, DVD, or BD Insert the end of a paper clip (1) into the release access in the front bezel of the drive. Press in gently on the paper clip until the tray is released, and then pull out the tray (2) until it stops. Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer edges of the disc.
Using external drives Removable external drives expand your options for storing and accessing information. A USB drive can be added by connecting the drive to a USB port on the computer or on an optional docking device (select models only). USB drives include the following types: ●...
Using optional external devices NOTE: For more information about required software and drivers, or to learn which computer port to use, refer to the manufacturer's instructions. To connect an external device to the computer: CAUTION: To reduce the risk of damage to the equipment when connecting a powered drive, be sure that the AC power cord is unplugged.
Replacing the hard drive CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing the hard drive from the hard drive bay. Do not remove the hard drive while the computer is on, in Suspend, or in Hibernation. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button.
Page 18
Remove the screws from the battery area. Your computer has either 2 or 3 screws that need to be removed. NOTE: Refer to the illustration that most closely matches your computer. Chapter 4 Replacing the hard drive...
Page 19
Turn the computer display-side up, and then remove the 2 screws from the back edge of the computer. Open the computer as far as possible. Slide the switch cover straight back towards the display, and then remove the switch cover.
Page 20
Remove the screws from the keyboard. Your computer has either 2 or 3 screws that need to be removed. NOTE: Refer to the illustration that most closely matches your computer. Slide the keyboard (1) towards the display assembly, and then turn the keyboard upside down (2) so that the keyboard cable is accessible.
Page 21
Remove the keyboard from the computer (3). Remove the screws from the top cover. Your computer has either 2 or 3 screws that need to be removed. NOTE: Refer to the illustration that most closely matches your computer.
Page 22
Slide the top cover back until it disengages from the base enclosure, and then rest the top cover on the computer so that the TouchPad cable is accessible. Release the ZIF connector (1) to which the TouchPad cable is connected, and then disconnect the TouchPad cable from the system board (2) by pulling upward.
Page 23
Lift the hard drive (3) out of the hard drive bay. To install a hard drive: Insert the hard drive into the hard drive bay (1). Use the Mylar tab (2) on the hard drive to slide the hard drive to the left to connect it to the system board.
Page 24
Place the top cover (1) on the computer, and then insert the TouchPad cable (2) into the ZIF connector (3) on the system board. Slide the top cover into place. Chapter 4 Replacing the hard drive...
Page 25
Replace the screws to the top cover. Your computer has either 2 or 3 screws that need to be installed. NOTE: Refer to the illustration that most closely matches your computer. Place the keyboard upside down on the top cover of the computer (1). Insert the keyboard cable (2) into the ZIF connector (3) on the system board.
Page 26
Turn over the keyboard (1) into the keyboard tray, and then slide the keyboard (2) into place. Replace the screws on the keyboard. Your computer has either 2 or 3 screws that need to be replaced. NOTE: Refer to the illustration that most closely matches your computer. Slide the switch cover into place.
Page 27
Close the computer display. Replace the 2 screws on the back edge of the computer.
Page 28
Replace the screws in the battery area. Your computer has either 2 or 3 screws that need to be replaced. NOTE: Refer to the illustration that most closely matches your computer. Turn the computer upside down on a flat surface and replace the battery. Reconnect external power and external devices.
Index airport security devices 1 hard disk drive external 11 installing 19 replacing 13 playing 6 hard drive removing 9 external 11 Blu-ray Disc (BD) 2, 3 installing 19 Blu-ray ROM DVD+/-RW replacing 13 SuperMulti Double-Layer LightScribe Drive 3 keyboard removing 16 copying or creating 8 playing 6...