Table of Contents
Advertisement
512F-2
06/'6/29
8:30
A_
Page
114
DataS:
m
Z
x
All data are transmitted by Hexadedma[ code
Two/One part Charmek 6th bit
This bit is used in a cable.ready system_
Using physka[ channei: 5th bit
If the channel band is NTSC air or NTSC _:able_ channel
turfing can be done by oMy physka[ cha_meL In this
case, using physical channel bit must be low(0).
gut if the channel band is ATSC air or ATSC cable, there
are two cases that physical channel enable or disable.
ffthe physical channel sending is meaningfhl, ..you should
set this bi_ low(0). If the physical channe[ sending is
meaningless, you should set this bit high(1 ).
Example)
1, Analog charmek NTSC cable, channel number(S5),
main pkt:ure Command: ma 00 23 xx xx xx xx 0t
attribute(Ox0I ): main picture, two part(it% not
mandatory)
using physlcat channel, NTSC cable _x£
data: don*t care major and minor channel number in
case analog channel tuning,
2. Digital channel: ATSC ak channel number(don't
know
ph_ica[ channel, major(30),
mino_(3)), sub picture
Command:
ma O0 ×x O0 1E OO 03 A2
attribute(O_2):
sub picture, two part, not using
physical channel, ATSC air 'x£ data: don't care analog
channel number in case digital channel tuning
3. Digital channel: A]SC air, channel number(physio
cal(20),major(20),
minor(3)),
sub picture Command:
ma 00 14 00 14 00 03 82
a_rlbute(Ox82):
sub picture, two part using physical
channel, ATSC air;
[Data21 [ D_tadI I D_t_q[SM[] [Set!D]
[] [NG] [Data0) Ix]
25. Channel Add/Del (Command: m b)
To add and delete the channels
Tr_smi_d_m [m] [b]I ] [Set [D][ ] [D'at_] [Cr]
Data 0: Channel Delete
Data 1: Channel Add
A@_Ow£dg_¢men_ [b] [ ]{Set [D] [ ] [DiKiNG) [Data] [×]
26.
Key (Command: mc)
To send IR remote key code.
Tn,_s_,isi_._ M M [ ] [SeD]
[ ][Da@ Iqs
Data Key code: Refer to page 116.
AcknowJ_,dgem_n_ [ c] [1 [Set [D] [ ] [OK/Nq
[Data] H
27.
Input select(Command: x b) (Main Picture Input)
TO select input source for TV.
Tran_misdon IX) [b][ j [Set ID] [] [Data] [Cr]
Data OO : DTV (Antenna)
Data 10 : Analog (Antenna)
Data 20 : AV1
Data 40 : Component
1
Data 50 : RGB DTV
Da_ 90 : HDMI1/DVI
Da_ 01 : DTV (Cable)
Data 11 : Analog (Cable)
Data 21 :/W2
Data 41 : Component 2
Data 60 : RGB PC
Data 91 : HDM[2
28.
PIP Input 5elect(Command: x y)
TO adiust input source for sub picture in PiP mode.
Tr_m_is@m [×] [y] [ ] [S_t ID][ ] [Data] [C(]
Data 00 : DTV (Antenna)
Data 01 : DTV (Cable)
Data 10 : Analog (Antenna)
Data 11 : Analog (Cable)
Data 20 : AVl
Data 21 : AV2
Ackno_,k, d gemg, n[ ]y][ ][Set K}]] I [OK/NG] [Data] [x_
1 14
Advertisement
Table of Contents
