Page of 24

Nextar X3-02 Important Safety Instructions Manual

Also See for X3-02:
Brochure - 1 page
Hardware manual - 21 pages
Software manual - 40 pages
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USE-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OF MOISTURE.
POWER SUPPLY:
Connect the supplied adapter to the side of the unit in the slot marked "DC 5V IN". Plug
the two-prong end of the power cord to an AC100-240V outlet. If you have difficulty
inserting the plug, turn it over and reinsert it. If the unit will not be used for a long time,
disconnect the plug from the outlet.
NOTE:
Before plugging the power cord into an AC outlet, make sure that all the connections
have been made.
CAUTION: These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so.
Refer to service manual for servicing instructions. To reduce the risk of fire or electric
shock, do not expose this apparatus to rain or moisture.
Important Safety
Instructions
1

   Related Manuals for Nextar X3-02

   Summary of Contents for Nextar X3-02

  • Page 1

    Important Safety Instructions CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USE-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric to persons.

  • Page 2

    Important Safety Instructions NOTES Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a damp cloth. Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions.

  • Page 3

    Important Safety Instructions Warning Failure to avoid the following potentially hazardous situations may result in injury or property damage. The unit is designed to provide you with route suggestions. It does not reflect road closures or road conditions, traffic congestion, weather conditions, or other factors that may affect safety or timing while driving.

  • Page 4: Accessories

    Accessories Accessories List ITEM NAME Owner’s Manual Power Adaptor Car Adaptor Mounting Bracket Mounting cradle USB Cable Touch Pen Dashboard mount disk Pouch NOTE Accessories and their parts numbers are subject to modification without prior notice due to improvements.

  • Page 5: Table Of Contents

    Contents …………………………………..………..1 Important Safety Instructions ……………………………….…………...4 Accessories ……………………………….…………...6 View of Main Unit ……………………………….……….…..8 System Connections …………………………….……….…….10 Power Supply Preparation ……………………………….…………..12 General Setup …………………………….……………..16 Playing Music ……………………………….…………..19 Photo Viewer …………………………….……………..21 Use of the Mount Accessories ……………………………………………22 Troubleshooting ……………………………………………23 Specifications...

  • Page 6: View Of Main Unit

    View of Main Unit Front and Side Panel POWER button Press for a longer time to enter or exit the standby mode. Card Port Insert the SD/MMC card into the port. Headphone Jack Used to connect headphones for private listening. When the headphones are connected to this jack, the speaker will be turned off automatically.

  • Page 7

    View of Main Unit Rear panel RESET button Press to reset the system. GPS Antenna Jack Used to connect the external GPS antenna(optional).

  • Page 8: System Connections

    System Connections Always ensure that the unit and any other external device connected to the unit are switched off and unplugged from the power supply before you attempt to connect the unit to any external device. Connecting to PC The unit is designed with a USB port which allows you to connect the unit to PC for map updating.

  • Page 9

    System Connections Inserting SD Card The unit is designed with SD/MMC Card jack which allows you to insert the SD/MMC card into the unit as shown below: Connecting to Earphones Connect the earphones to the right side of the unit for private listening. Note: This unit comes without earphones.

  • Page 10: Power Supply Preparation

    Power Supply Preparation Using the AC Adaptor The player is supplied with an AC adaptor for powering the unit and charging the battery. Connect AC adaptor to the right side of the player in the jack marked DC 5V IN, as shown on the right. Plug the two-prong end of the power cord into a grounded electrical outlet.

  • Page 11

    Power Supply Preparation About Rechargeable Battery Your portable GPS player comes with a built-in rechargeable battery. Charge the battery fully before initial use. Charging time is normally about 3.5 hours. A fully charged battery delivers about 3 hours of use. Working conditions and precautions for the rechargeable battery New batteries should be fully charged before initial use.

  • Page 12: General Setup

    General Setup General Setup When turn on the unit, the screen will display the main menu later as shown below: In the main menu, there are four items for selecting. Touch the corresponding item to enter. to enter navigation mode; tap to enter the MP3 player;...

  • Page 13

    General Setup Language in the setting menu to enter Language setting menu for language selecting, as shown below: Tap the buttons to select language. Then tap to confirm or tap to cancel. Backlight in the settings menu to enter Backlight setting menu for backlight adjusting, as shown below: Tap the first group buttons to adjust the backlight level.

  • Page 14

    General Setup Date & Time in the settings menu to enter Date & Time setting menu for changing to the current time zone, as shown below: Tap the buttons to select the proper Time Zone. Tap the buttons of Date group to change the corresponding date and tap the buttons of Time group to change the corresponding time.

  • Page 15

    General Setup Calibrate in the settings menu to calibrate, the screen will display as below: This item is used to calibrate the sensitivity of the touch screen. Tap the center of “+” as it moves around the screen. If you touch the center of “+” every time, it will disappear after having moved through a cycle (center→top left→bottom left→bottom right→top right).

  • Page 16: Playing Music

    Playing Music The unit is designed with SD card slot and supports MP3 and WMA format files playback. You can insert the SD card with MP3 or WMA files in the unit for music enjoyment. Note: Do not store MP3 or WWA format files in the Flash storage, for the flash storage is used to store map data, any attempt to open the Flash storage may result in the map data missing and lost.

  • Page 17

    Playing Music Double tap the MMC_Storage icon to open the folder, the songs in the folder will be displayed on the screen. Select the songs that you want to add into the playlist and tap to confirm. The songs selected will be added into the playlist, as shown below: In the playlist, double tap the songs to start playback.

  • Page 18

    Playing Music During playback, tap button to go to the previous track. During playback, tap button to go to the next track. During playback, tap button to pause playback, or in stop status, tap the button to resume playback. During playback, tap button to stop playback.

  • Page 19: Photo Viewer

    Photo Viewer The unit is designed with SD card slot and supports JPEG format files playback. You can insert the SD card with JPEG files in the unit for picture view. Note: Do not store JPEG format files in the Flash storage, for the flash storage is used to store map data, any attempt to open the Flash storage may result in the map data missing and lost.

  • Page 20

    Photo Viewer In the folders menu, tap to move the folders list up or down; tap to return to the previous menu. Tap to play the selected picture or to enter the selected folder; you can also realize these functions by double tapping the item you want to play or enter. In the folders menu, double tap the MMC_Storage icon to open the folder, then the pictures in the folder will be displayed on the screen.

  • Page 21

    Use of Mount Accessories When using the unit in vehicle, you can use the supplied mount accessories (mount bracket and mount cradle) to mount the unit in the vehicle. Take the following steps to operate: See Fig. 1. Push the mount cradle to mount bracket. See Fig.

  • Page 22: Troubleshooting

    Troubleshooting Take steps described in the tables below to solve simple problems before contacting customer service. If you suspect something wrong with this unit, immediately turn the power off and disconnect the power connector from the unit. Never try to repair the unit yourself because it is dangerous to do so.

  • Page 23: Specifications

    Specifications TFT screen size 3.5 inches Frequency Response 20Hz~20kHz ≥65dB Audio Signal-to-noise Rate ≤-20dB (1kHz) Audio distortion or noise ≥70dB (1kHz) Channel Separation ≥80dB (1kHz) Dynamic Range Power AC 100~240V, 50/60Hz; DC 5V Power Consumption < 8W Dimensions 100mmX76mmX22mm (L*W*D) Weight About 0.25kg DESIGN AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE...

  • Page 24

    © 2008 Nextar (Hong Kong) Limited. Nextar is a trademark and service mark of Nextar (Hong Kong) Limited. All other brand names, trademarks and service marks are property of their owners. Nextar may find it necessary to modify, amend or otherwise change or update this manual.

Comments to this Manuals

Symbols: 0
Latest comments: