Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Panasonic AJ-YAD455
Summary of Contents for Panasonic AJ-YAD455
- Page 1 Digital Video Interface Board Operating Instructions...
-
Page 2: Precautions
Precautions O Do not touch this product with wet hands. O Do not drop this product or subject it to other strong shocks. O Do not attempt to modify this product. Doing so may cause it to malfunction. THE AJ-YAD455P IS A DIGITAL VIDEO INTERFACE BOARD WHICH IS DESIGNED TO BE USED ONLY WITH THE AJ-D455 DIGITAL VTR: IT CANNOT BE USED WITH EITHER THE AJ-D450 OR AJ-D440. -
Page 3: Table Of Contents
Contents Precautions ........1 Model supported ....... . 1 Features . -
Page 4: Specifications
Specifications $ Digital video interface board Dimensions (WtHtD): 5-11/16˝t5-9/16˝t9/16˝ (143t140t13 mm) Weight: 0.246 lb (112 g) $ Input/output facility Connector: 6-pin type Transfer rate: 100 Mbps Transfer data: Compliant with IEC-61883/FDS (Part-1, 2) Control commands: Compliant with AV/C command set Accessories Connector board (t1) Connecting cable (t1) -
Page 5: Installation In Aj-D455
Installation in AJ-D455 Consult your dealer concerning the installation of the digital video interface board. The AJ-YAD455P must be installed in the AJ-D455 in order for it to be used. Follow the procedure below for installation. Disconnect the power cord from the unit. Check that the DIP switches on the AJ-YAD455P are set to the positions shown in the figure below. - Page 6 Installation in AJ-D455 Remove the screw and the board clamp. Board clamp Screw Remove the 6 screws and pull the rear panel directly backwards to remove. Rear panel Screws 5(E)
- Page 7 Installation in AJ-D455 Remove the screw and remove the blank panel from the rear panel. Blank panel Screw Attach the accessory connector board to the rear panel. Pass the wiring through the rear panel, attach the top side of the connector board and secure the lower side of the board in place with the screw, as shown in the diagram below.
- Page 8 Installation in AJ-D455 Pass the wiring through the unit and secure the rear panel with the 6 screws. Ensure that wiring and connections are as shown in the respective diagrams below. Clampers View from rear Wiring Diagram Connections Diagram Insert the interface board into the front panel side of the slot marked “F3”.
- Page 9 Installation in AJ-D455 Attach the board clamp with the screw and secure the top panel to the unit with the 2 coin screws. Coin screws Screw Board clamp 8(E)
-
Page 10: Aj-D455 Settings
AJ-D455 settings NTSC regions Check that the setup menu item No.220 (AV/C CMD SEL) is set to “ON.” Check that “AUTO” has been selected as the setup menu item No.882 (DIF IN CH) and No.883 (DIF OUT CH) settings. When inputting signals from the digital video interface board, set the VIDEO IN switch on the front panel to “DV/DVCPRO.”... - Page 11 AJ-D455 settings NTSC regions <Note> O The output data format can be converted by setting the setup menu item No.881 (DIF TYPE). DIF TYPE setting Playback tape Output format DVCPRO DVCPRO DVCPRO DVCPRO ( DVCPRO DVCPRO DVCPRO AUTO 2: “CH1/CH2” or “CH3/CH4” can be selected by setup menu item No.890 (DIF AUD OUT) when the 32 KHz/ 4CH audio signals are recorded on the playback tape.
- Page 12 AJ-D455 settings PAL regions Check that the setup menu item No.220 (AV/C CMD SEL) is set to “ON.” Check that “AUTO” has been selected as the setup menu item No.882 (DIF IN CH) and No.883 (DIF OUT CH) settings. When inputting signals from the digital video interface board, set the VIDEO IN switch on the front panel to “DV/DVCPRO.”...
-
Page 13: Precautions For Use
Precautions for use O Connect the AJ-YAD455P with other units in a 1:1 format. O Use the special-purpose cable (AJ-DTC2P or AJ-DTC4P) to connect the AJ-YAD455P with the AJ-D455, AJ-D250 or AJ-D230H. O Turning the power of the connected units ON or OFF or connecting or disconnecting the interface cable may disrupt the AV signals. -
Page 14: Setup Menus
Setup menus The following setup menu items can be used when the AJ- YAD455P has been installed in the AJ-D455. Item Setting Super- Super- Description of settings imposed imposed display display AV/C 0000 For selecting whether to use the digital video interface AV/C... - Page 15 Setup menus Item Setting Super- Super- Description of settings imposed imposed display display 0000 For setting the output channels. 0-63: These are fixed at designated values. 0063 64: This is not fixed at a designated 0064 AUTO value. It is initialized to 63 when the power is turned on or when cable connected...
-
Page 16: Diag Menu
DIAG menu By installing the AJ-YAD455P in the AJ-D455, a DIAG menu screen showing information relating to the digital video interface is additionally provided. For details on the DIAG menu display method, refer to the operating instructions of the AJ-D455. Item Description EUI-64... -
Page 17: Warning Messages
Warning messages By installing the AJ-YAD455P in the AJ-D455, the following warning messages are additionally provided. These messages will appear on the mode display when “T&S&M” has been selected as the setup menu item No.003 (DISPLAY SEL) setting. Display on monitor screen Description Operation... - Page 18 DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA Executive Office: 3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500 EASTERN ZONE: One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621 Southeast Region: 1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835 Central Region:...