Download Print this page
Edelbrock 541583 Installation Instructions
Edelbrock 541583 Installation Instructions

Edelbrock 541583 Installation Instructions

Edelbrock russell complete fuel system installation instructions

Advertisement

Quick Links

Please study these instructions carefully before installing your new complete fuel system kit. If you have any questions, please call
our Technical Hotline at: 1-800-416-8628, 7:00 am to 5:00 pm, Monday - Friday, Pacific Standard Time or e-mail us at
Edelbrock@Edelbrock.com.
❑ 1
Edelbrock Fuel Pump #1791
❑ 1
Russell 8" 60-micron ProFilter with clamp
❑ 1
Edelbrock Electric Fuel Pump Relay Kit #1795
❑ 1
Russell Fuel Feed Line Kit (641580 / 641583
kits include 3" filter)
❑ 2
Russell Carburetor Adapter Fittings (641590 /
641593 kits only)
❑ 2
Russell adapter fittings for fuel pump (3/8" x -6
AN adapter)
❑ 3
Russell straight hose ends
❑ 1
Russell 90° hose ends
❑ 1
Russell 45° hose end
❑ Basic hand tools
❑ Miscellaneous hardware for mounting components
❑ Drill motor & bits
❑ Wire crimpers or soldering equipment
❑ Extra wire (Red & Black, 12 gauge & 18 gauge)
❑ 10A inline fuse
Gasoline and gasoline fumes are extremely flammable. Work in a well-ventilated area away from open flames,
sparks, or other sources of ignition. Try to contain gasoline when connections are loosened, and clean up any
spills immediately. Failure to do so can result in a fire or explosion.
Proper installation is the responsibility of the installer. Improper installation will void warranty and may result in
© 2007 Edelbrock Corporation
Brochure No. 63-641580
Catalog #641580 & #641583 for Edelbrock Thunder Series
Catalog #641590 & #641593 for Holley or BG Demon Carburetors
KIT CONTENTS
TOOLS & SUPPLIES RECOMMENDED
WARNING!!!
IMPORTANT NOTE:
poor performance and engine or vehicle damage.
Page 1 of 4
RUSSELL COMPLETE FUEL SYSTEM KIT
FOR CARBURETED VEHICLES
INSTALLATION INSTRUCTIONS
❑ 1
Russell -6 Tube Seal hose clamp with cover
❑ 20 ft.
Russell -6 hose
❑ 10
Russell -6 cushion clamps
❑ 12
Cable ties
❑ 1
Edelbrock fuel pump block-off plate with
gaskets & hardware for small-block Chevrolet
❑ 1
Edelbrock fuel pump block-off plate with
gaskets & hardware for big-block Chevrolet &
Ford/Chrysler/AMC engines
❑ 10 ft.
Russell 3/16" Wrap-It wire protective sleeve
❑ 10 ft.
Russell 5/16" Wrap-It wire protective sleeve
❑ AN Wrenches
❑ Pipe thread sealant
❑ Multimeter or test light
❑ Wire strippers
❑ Wire terminals & connectors
Catalog #641580, 541583, 641590, & 641593
AVS Carburetors
Rev. 10/07 - AJ/mc

Advertisement

loading

Summary of Contents for Edelbrock 541583

  • Page 1 Proper installation is the responsibility of the installer. Improper installation will void warranty and may result in © 2007 Edelbrock Corporation Brochure No. 63-641580 Catalog #641580 & #641583 for Edelbrock Thunder Series Catalog #641590 & #641593 for Holley or BG Demon Carburetors KIT CONTENTS TOOLS &...
  • Page 2 8a. Install supplied Russell carburetor fuel feed line using supplied banjo bolts and washers (See Fig. 2) . 8b. Install small Edelbrock filter onto feed line inlet (See Fig. 2) . NOTE: An additional Russell adapter fitting or hose assembly may be required to relocate filter if application has inadequate clearance.
  • Page 3 © 2007 Edelbrock Corporation Brochure No. 63-641580 Also, some motorsports FUEL PUMP RELAY 16. Mount Edelbrock fuel pump relay at suitable location 17. Run one large (12 gauge) red relay wire back to red lead Page 3 of 4 Fig. 5 under hood (e.g.
  • Page 4 Fig. 8 Fig. 9 Edelbrock Corporation, 2700 California St., Torrance, CA 90503 © 2007 Edelbrock Corporation Brochure No. 63-641580 18. Connect other large (12 gauge) red relay wire to positive(+) battery terminal. 19. Connect small pink relay wire to 12V switched (key-on) power supply (e.g.

This manual is also suitable for:

641580641590641593641583