Advertisement
Quick Links
Model 2083/08
Code Translator
Installation and Operation Instructions
This manual describes the installation and operating procedures for the model 2083/08 Code Translator. The 2083/08 is an
interface unit used with American Dynamics Switching Systems. This unit translates codes to enable the use of all American
Dynamics Matrix Switchers with the 1261/1263/1265/1267 series of domes.
Advertisement
Summary of Contents for American Dynamics AD2083/08
- Page 1 This manual describes the installation and operating procedures for the model 2083/08 Code Translator. The 2083/08 is an interface unit used with American Dynamics Switching Systems. This unit translates codes to enable the use of all American Dynamics Matrix Switchers with the 1261/1263/1265/1267 series of domes.
- Page 2 The software/firmware furnished with this equipment is confidential to and is copyrighted by SENSORMATIC ELECTRONICS CORPORATION. It is not to be copied or disclosed in any manner without the express written consent of SENSORMATIC. The software/firmware is furnished to the purchaser under a license for use on a single system. Information furnished by SENSORMATIC is believed to be accurate and reliable.
- Page 3 AMERICAN DYNAMICS The installation of this product should be made by qualified service personnel and should conform to all local codes. The lightning flash with arrowhead symbol, within equilateral CAUTION triangle, is intended to alert the user to the presence of uninsulated RISK OF ELECTRIC SHOCK DO NOT OPEN "dangerous voltage"...
-
Page 5: Table Of Contents
Table of Contents Product Description ...............1 Installation ................1 Setup ..................2 Connections ................3 Operation ................4 Typical Connections..........Appendix... -
Page 7: Product Description
PRODUCT DESCRIPTION Rack Mounting The 2083/08 Code Translator is used as an interface to American Dynamics switching systems. The 2083/08 allows The 2083/08 is shipped with the mounting ears installed flush retrofit or new installation of American Dynamic switchers with the front panel, and can be mounted to the front of a where the 1261/1263/1265/1267 series of dome camera control standard 19-inch rack. -
Page 8: Setup
SETUP SETUP Camera Block Assignments Baud Rate Selection Four 8-position DIP switches (S1, S2, S3, and S4) are located - CAUTION - on the rear panel of the 2083/08, as shown in Figure 1, page 1. The following internal adjustments, requiring removal The settings of these DIP switches determine the cameras of the top cover, will expose hazardous-voltage associated with the connectors in each of the four rear panel... -
Page 9: Connections
CONNECTIONS CONNECTIONS Dome Interface Connectors Data Line Connectors Eight 12-pin connectors on the rear of the 2083/08 Code Two DATA LINE BNC connectors are provided on the rear Translator panel are provided for transmitting RS-422 codes to panel, labeled IN and OUT. The IN BNC is used to receive 1261/1263/1265/1267 series domes. -
Page 10: Operation
320 inlet and the power source. The cord should conform to all 1261/1263/1265/1267 dome features. This includes the national and local use code requirements. Two models are standard American Dynamics keyboard functions for camera available, depending on the power source: Pan, Tilt, and Lens control. - Page 11 APPENDIX...
- Page 13 TYPICAL SYSTEM CONNECTIONS 1995 TO 2083/08 PORT PORT PORT PORT PORT PORT PORT PORT PORT PORT 1995 COAX VIDEO CABLE DATA LINE GROUP ABCD B W S NO NC C ABCD POWER 120V ALARM ABCD 60Hz CODE ABCD INPUT OUTPUT 2083/08 TERMINATION, IF NOT LOOPED TO OTHER DATA LINE UNITS...
- Page 14 TYPICAL SYSTEM CONNECTIONS 1996 TO 2083/08 DATA LINE PROG MON PORTS 120V 60Hz 1996 COAX VIDEO CABLE DATA LINE GROUP ABCD B W S NO NC C ABCD POWER 120V ALARM ABCD 60Hz CODE ABCD INPUT OUTPUT 2083/08 TERMINATION, IF NOT LOOPED TO OTHER DATA LINE UNITS...
- Page 15 TYPICAL SYSTEM CONNECTIONS 2083/08 to 1261/1263/1265/1267 Domes J2Pins: 3 - Transmit - 14-pin CONNECTOR PLUG, J2 4 - Transmit + 1261/1263/1265/1267 DOME 18 AWG SHIELDED TWISTED PAIR, BELDEN 8760 OR EQUIVALENT DATA LINE GROUP ABCD B W S NO NC C ABCD POWER 120V...
- Page 16 TYPICAL SYSTEM CONNECTIONS 2150 TO 2083/08 RELAY -CODE- ALARMS CAMERAS BWS BWS BWS BWS MONITORS 120V 60Hz KEYBOARDS RS232 PORTS 2150 18 AWG SHIELDED TWISTED PAIR, BELDEN 8760 OR EQUIVALENT DATA LINE GROUP ABCD B W S NO NC C ABCD POWER 120V...
- Page 17 TYPICAL SYSTEM CONNECTIONS 1650 TO 2083/08 RS-232 MONITOR MONITOR MONITOR MONITOR 1650 18 AWG SHIELDED TWISTED PAIR, BELDEN 8760 OR EQUIVALENT DATA LINE GROUP ABCD B W S NO NC C ABCD POWER 120V ALARM ABCD 60Hz CODE ABCD INPUT OUTPUT 2083/08...
-
Page 19: Declaration Of Conformity
Declaration of Conformity Manufacturer: Sensormatic CCTV Systems Division Manufacturer’s Address: Sensormatic CCTV Systems Division Sensormatic CCTV Systems Division 1 Blue Hill Plaza 600 Bradley Hill Road Pearl River, New York, 10965 USA Blauvelt, NY 10913 USA Sensormatic Electronics Corporation Sensormatic Electronics Corporation (IRL) LTD State Rd. - Page 20 Weight: 7 lbs. (3.2 Kg) Dimensions: 3.5" H x 17" W x 7.75" D (89 x 432 x 197 mm) An American Dynamics Product Designed and built by Sensormatic CCTV Systems Division One Blue Hill Plaza Pearl River, New York, 10965...