Table of Contents
Advertisement
Quick Links
Model 2083/06
Code Translator
Installation and Operation Instructions
This manual describes the installation and operating procedures for the model 2083/06 Code Translator. The 2083/06 Code
Translator is an interface unit used with American Dynamics Switching Systems. This unit translates codes to enable the use of
all American Dynamics equipment with that of Pelco Intercept Domes.
Advertisement
Table of Contents
Summary of Contents for American Dynamics 2083/06
- Page 1 This manual describes the installation and operating procedures for the model 2083/06 Code Translator. The 2083/06 Code Translator is an interface unit used with American Dynamics Switching Systems. This unit translates codes to enable the use of all American Dynamics equipment with that of Pelco Intercept Domes.
- Page 2 This software/firmware is confidential to and is copyrighted by SENSORMATIC ELECTRONICS CORPORATION. It is not to be copied or disclosed in any manner without the express written consent of SENSORMATIC. The software is furnished to the purchaser under a license for use on a single system. NOTE: Information furnished by SENSORMATIC is believed to be accurate and reliable.
- Page 3 AMERICAN DYNAMICS The installation of this product should be made by qualified service personnel and should conform to all local codes. The lightning flash with arrowhead symbol, within equilateral CAUTION triangle, is intended to alert the user to the presence of uninsulated RISK OF ELECTRIC SHOCK DO NOT OPEN "dangerous voltage"...
-
Page 5: Table Of Contents
Table of Contents Product Description ...............1 Installation ................1 Setup ..................2 Camera Block Assignment..........2 Camera Mode ..............2 Baud Rate Selection ............2 Connections ................5 Pelco Interface Connectors ..........5 Control Code Connector ..........5 Data Line Connector ............5 Operation ................6 Power Sources ..............6 Operating Indicators............6 Controlling Pelco Receiver Features........6 Typical Connections..........Appendix... -
Page 7: Product Description
American Dynamics switching systems. The 2083/06 allows The 2083/06 is shipped with the mounting ears installed flush retrofit or new installation of American Dynamics switchers with the front panel, and can be mounted to the front of a where non-AD remote camera control systems are in place or standard 19-inch rack. -
Page 8: Setup
SETUP SETUP - CAUTION - The following internal adjustments expose hazardous- Camera Block Assignments voltage components and allow access to dangerous electric shock potentials. These adjustments should be The 2083/06 Code Translator must be set to identify the range made only by qualified service personnel. of camera numbers to be controlled by the unit. - Page 9 SETUP Table 3 - CAMERA NUMBER RANGE The following table shows the DIP switch settings for the camera number range of each connector group. The active positions of switches S1 - S4 are labeled A, B, C, and D on the rear panel (Figure 1). The active positions of DIP switch S6 are labeled 1 through 8 on the internal DIP switch (Figure 3).
- Page 10 SETUP Table 3 - CAMERA NUMBER RANGE (Continued) The following table shows the DIP switch settings for the camera number range of each connector group. The active positions of switches S1 - S4 are labeled A, B, C, and D on the rear panel (Figure 1). The active positions of DIP switch S6 are labeled 1 through 8 on the internal DIP switch (Figure 3).
-
Page 11: Connections
CONNECTIONS CONNECTIONS Pelco Interface Connectors Data Line Connectors Eight 12-pin connectors on the rear panel of the 2083/06 are Two DATA LINE BNC connectors are provided on the rear used for transmitting and receiving codes with Pelco Intercept panel, labeled IN and OUT. The IN is used to receive camera Domes. -
Page 12: Operation
OPERATION OPERATION Controlling Pelco Receiver Features Power Sources The 2083/06 supports the transmitted codes for Pelco Intercept DO NOT CONNECT THE EQUIPMENT TO A POWER Domes features. This includes the standard American SOURCE UNTIL READY TO "POWER UP''. Make all Dynamics keyboard functions for camera Pan, Tilt, and Lens connections to the 2083/06 code input and relay connections control. - Page 13 OPERATION Table 4 - Pelco Intercept Dome Commands Pelco Function Dome Action AD Keyboard Command Pan, Tilt, Zoom, Focus, and Iris Functions Pan, Tilt, Zoom, Focus, and Iris Controls Presets (For those Pelco domes which implement preset capability): Set Preset 1 - 32 Saves camera position as preset 1 - 32 1 - 32 Set Shot Goto Preset 1 - 32...
- Page 15 APPENDIX...
- Page 17 TYPICAL SYSTEM CONNECTIONS 1995 TO 2083/06 DATA LINE GROUP ABCD B W S NO NC C ABCD POWER 120V ALARM ABCD 60Hz CODE ABCD INPUT OUTPUT 2083/06 COAX CABLE PORT PORT PORT PORT PORT PORT PORT PORT PORT PORT 1995...
- Page 18 TYPICAL SYSTEM CONNECTIONS 1650 TO 2083/06 DATA LINE GROUP ABCD B W S NO NC C ABCD POWER 120V ALARM ABCD 60Hz CODE ABCD INPUT OUTPUT 2083 18 AWG SHIELDED TWISTED PAIR BELDEN 8760 OR EQUIVALENT RS-232 MONITOR MONITOR MONITOR MONITOR 1650A/1650B...
- Page 19 TYPICAL SYSTEM CONNECTIONS 1996 TO 2083/06 DATA LINE GROUP ABCD B W S NO NC C ABCD POWER 120V ALARM ABCD 60Hz CODE ABCD INPUT OUTPUT 2083/06 COAX CABLE DATA LINE PROG MON PORTS 120V 60Hz 1996...
- Page 20 TYPICAL SYSTEM CONNECTIONS 2150 TO 2083/06 DATA LINE GROUP ABCD B W S NO NC C ABCD POWER 120V ALARM ABCD 60Hz CODE ABCD INPUT OUTPUT 2083/06 18 AWG SHIELDED TWISTED PAIR, BELDEN 8760 OR EQUIVALENT ALARMS RELAY -CODE- CAMERAS BWS BWS BWS BWS MONITORS 120V...
- Page 21 TYPICAL SYSTEM CONNECTIONS 2083/06 to Pelco Interceptor Dome 25-pin CONNECTOR PLUG, P13 in Pelco Back Box P13 Pins: PELCO BACK BOX 3 - R+ 5 - T+ 6 - R- 7 - T- PELCO INTERCEPTOR DOME 18 AWG, SHIELDED CABLE DATA LINE GROUP ABCD...
- Page 23 Declaration of Conformity Manufacturer: Sensormatic CCTV Systems Division Manufacturer’s Address: Sensormatic CCTV Systems Division Sensormatic CCTV Systems Division 1 Blue Hill Plaza 600 Bradley Hill Road Pearl River, New York, 10965 USA Blauvelt, NY 10913 USA Sensormatic Electronics Corporation Sensormatic Electronics Corporation (IRL) LTD State Rd.
- Page 24 Weight: 7 lbs. (3.2 Kg) Dimensions: 3.5" H x 17" W x 7.75" D (89 x 432 x 197 mm) An American Dynamics Product Designed and built by Sensormatic CCTV Systems Division One Blue Hill Plaza Pearl River, New York, 10965...