Advertisement
Quick Links
Advertisement
Related Manuals for Edelbrock 2010
Summary of Contents for Edelbrock 2010
- Page 1 Edelbrock 2010-2012 Camaro SS Supercharger Part #’s: 1596, 1597, 1598, 1599, 15997...
-
Page 2: Tools Required
Thank you for purchasing the Edelbrock 6.2L GM Supercharger System for the 2010 Chevy Camaro. The Edelbrock E- Force Supercharger System for the 2010 Camaro SS utilizes Eaton’s new Gen VI TVS Supercharger rotors, featuring a four lobe design with a full 160 deg. of twist for maximum flow, minimum temperature rise, quiet operation, and the reliability for which Eaton is known. -
Page 3: Important Warnings
Due to the complexity of the Edelbrock E-Force Supercharging system, it is recommended that this system only be installed by a qualified professional with access to a service lift, pneumatic tools, and a strong familiarity with automotive service procedures. - Page 4 Edelbrock E-Force Supercharger System for the 2010-2012 Camaro SS Installation Instructions INSTALLATION HARDWARE IDENTIFICATION GUIDE Bag #1 (3x) - M8 x 1.25 x 100mm Socket Head Bolt (1x) - M10 x 1.5 x 65mm Socket Head Bolt (1x) - M10 x 1.5 x 65mm Hex Flange Bolt (3x) - M8 x 1.25 x 20mm...
- Page 5 (1x) - 1/4” x 3/4” Steel Dowel ©2012 Edelbrock LLC Part #1596, 1597, 1598, 1599 Edelbrock E-Force Supercharger System for (8x) - M6 x 1 x 45mm Hex Flange Bolt (1x) - GM Factory Harmonic Balancer Bolt (1x) - 15/64” High Speed Steel Drill Bit (1x) - .2500”...
- Page 6 Edelbrock E-Force Supercharger System for the 2010-2012 Camaro SS Installation Instructions Bag #5 (4x) - Coil Cover Bracket Grommet (1x) - Coil Cover Dipstick Grommet (4x) - Coil Cover Bracket (4x) - Coil Cover Retainer Stud (4x) - Coil Cover Standoff Brochure #63-1598 ©2012 Edelbrock LLC...
- Page 7 Edelbrock E-Force Supercharger System for the 2010-2012 Camaro SS Installation Instructions HOSE IDENTIFICATION GUIDE Intercooler Water Pump to Heat Exchanger Hose Heater Core Hose Assembly Fuel Rail Inlet Fuel Rail Crossover Intercooler Reservoir to Water Pump Hose Manifold to EVAP Solenoid Hose (18”)
- Page 8 In the rare occurrence that you encounter an error message during the test flash procedure, please refer to pg. 27, titled Email Edelbrock Your Stock PCM Calibration. Post Successful Test Flash If you are ready to install the supercharger, proceed to Step...
- Page 9 ©2012 Edelbrock LLC Part #1596, 1597, 1598, 1599 Edelbrock E-Force Supercharger System for the 2010-2012 Camaro SS Installation Instructions 4. Lift and support the front end of the vehicle using a service lift or jack and appropriately load rated jack stands then loosen and remove the lug nuts from both front wheels.
- Page 10 13. Remove the oil fill cap and remove the plastic engine cover. Reinstall the oil fill cap. ©2012 Edelbrock LLC Part #1596, 1597, 1598, 1599 Edelbrock E-Force Supercharger System for the 2010-2012 Camaro SS Installation Instructions 14. Disconnect passenger side PCV tube from the valve cover then use a flat head screwdriver to loosen the worm clamp retaining the air intake tube to the throttle body.
- Page 11 21. Use a 10mm socket to remove the nut holding down the fuel line clamp then remove the fuel line and clamp. ©2012 Edelbrock LLC Part #1596, 1597, 1598, 1599 Edelbrock E-Force Supercharger System for the 2010-2012 Camaro SS Installation Instructions 22. Disconnect the two ignition harness connectors, the eight spark plug wires from the ignition coils and the eight fuel injector electrical connectors.
- Page 12 28. Disconnect the PCV tube from the engine valley cover. 29. Remove the manifold insulating cover. ©2012 Edelbrock LLC Part #1596, 1597, 1598, 1599 Edelbrock E-Force Supercharger System for the 2010-2012 Camaro SS Installation Instructions 30. Use an 8mm socket to remove the nine remaining manifold bolts.
- Page 13 38. Rotate each solenoid 90° and remove them. ©2012 Edelbrock LLC Part #1596, 1597, 1598, 1599 Edelbrock E-Force Supercharger System for the 2010-2012 Camaro SS Installation Instructions 39. Use a T-30 Torx driver to remove the twenty bolts holding the steel sandwich in place and remove it.
- Page 14 Remove the radiator cap then loosen the petcock to drain the engine coolant. ©2012 Edelbrock LLC Part #1596, 1597, 1598, 1599 Edelbrock E-Force Supercharger System for the 2010-2012 Camaro SS Installation Instructions 51. Disconnect the two heater hoses from the firewall using a shop rag to absorb any excess coolant.
- Page 15 15mm deep socket to remove the ground strap stud. ©2012 Edelbrock LLC Part #1596, 1597, 1598, 1599 Edelbrock E-Force Supercharger System for the 2010-2012 Camaro SS Installation Instructions 58. Apply blue Loctite to the threads of the stock...
- Page 16 65. Disconnect the oil level sensor electrical connector from the passenger side of the oil pan. ©2012 Edelbrock LLC Part #1596, 1597, 1598, 1599 Edelbrock E-Force Supercharger System for the 2010-2012 Camaro SS Installation Instructions 66. Use a 10mm socket to remove the starter support bracket bolt.
- Page 17 NOTE: Convertible models are equipped with a brace that connects the frame extensions, this brace will need to be removed and replaced with the Edelbrock Convertible Brace (Part #15956, Sold Separately) as it interferes with the installation of the Edelbrock heat exchanger.
- Page 18 ©2012 Edelbrock LLC Part #1596, 1597, 1598, 1599 Edelbrock E-Force Supercharger System for the 2010-2012 Camaro SS Installation Instructions 96. Use a uni-bit to drill a 1-1/8” hole in the lower radiator shroud to allow the hose to slide onto the water pump outlet fitting.
- Page 19 2010-2012 Camaro SS Installation Instructions Figure - 2b 103. FOR 2010 - ‘11 MODEL YEARS ONLY Use a 10mm socket to remove the upper-outside bolt from the back- passenger side of the radiator fan; retain the bolt as it will be re-used.
- Page 20 108a. FOR 2010 - ‘11 MODEL YEARS ONLY Secure the lower intercooler reservoir bracket to the back of the fan by using a 10mm socket to re-install the stock bolt onto the standoff stud.
- Page 21 113. Connect the TMAP harness to the TMAP sensor at the rear of the supercharger manifold. ©2012 Edelbrock LLC Part #1596, 1597, 1598, 1599 Edelbrock E-Force Supercharger System for the 2010-2012 Camaro SS Installation Instructions 114. Remove the tape covering the intake ports. Since...
- Page 22 ©2012 Edelbrock LLC Part #1596, 1597, 1598, 1599 Edelbrock E-Force Supercharger System for the 2010-2012 Camaro SS Installation Instructions 122. Clip the Fuel Rail Crossover line onto the driver side fuel rail fitting.
- Page 23 Bag #2. Refer to figure 4 on page 19. ©2012 Edelbrock LLC Part #1596, 1597, 1598, 1599 Edelbrock E-Force Supercharger System for the 2010-2012 Camaro SS Installation Instructions 135. Install Driver Side Manifold to Intercooler Reservoir Hose between the manifold and reservoir then secure the reservoir fitting with a hose clamp supplied in Bag #2.
- Page 24 144. Use a flathead screwdriver to tighten the worm clamps on each end of the silicone tube. ©2012 Edelbrock LLC Part #1596, 1597, 1598, 1599 Edelbrock E-Force Supercharger System for the 2010-2012 Camaro SS Installation Instructions 145. Connect the stock MAP & MAF sensor wiring harness connectors into the supplied TMAP wiring harness then connect the TMAP harness to the MAF sensor.
- Page 25 ©2012 Edelbrock LLC Part #1596, 1597, 1598, 1599 Edelbrock E-Force Supercharger System for the 2010-2012 Camaro SS Installation Instructions 153. Use a 10mm deep socket to install the supplied ball studs into the new coil covers.
- Page 26 100 ft/lbs. If you have yet to flash your ECU, then proceed with steps 163 - 176, otherwise disregard them. 163. It is recommended that you check the Edelbrock website (http://www.edelbrock.com/automotive_new/mc/ superchargers/fuel_injected_soft-tech.shtml) to confirm that you have the latest calibration. Once you have found the latest tune on the site, power on the programmer, press the left arrow and select the Device Info option.
- Page 27 182. Congratulations on the installation of your new Edelbrock E-Force Supercharger System. If you have any questions, please call our Technical Support hotline and one of our technicians will be happy to assist you.
- Page 28 • If the upload fails, you will be asked to AUTO DETECT, press SELECT and follow the prompts on the sceen. If the auto detect fail, then please contact Edelbrock Tech support @ 800-416-8628 • Once the stock calibration has loaded, disconnect the programmer from the OBD-II connector and connect it to your PC using the supplied USB cable.