Zone Audio Setup; Power On Level Setup; Volume Limit Setup - Pioneer VSX-9040TXH - 110 Watt x 7 Direct Energy Amplification Receiver Operating Instructions Manual

The system and the other setup
3 Select the 'Video Input' setting you want.
When the multi-channel input is selected as an input
function, you can display the video images of other input
functions. The video input can be selected from the
following: DVD, TV/SAT, DVR, VIDEO (VSX-9140TXH only),
VIDEO 1, VIDEO 2 (VSX-9040TXH only), OFF.
4d2.Multi Ch In Setup
A/V RECEIVER
SW Input Gain :
Video Input :
Exit
4 When you're finished, press RETURN.
You will return to the Other Setup menu.

ZONE Audio Setup

If you've made MULTI-ZONE connections (see Using the
MULTI-ZONE controls on page 69), you may need to
specify your volume setting.
1 Select 'ZONE Audio Setup' from the Other Setup
menu.
4d.Other Setup
A/V RECEIVER
1. KURO LINK Setup
2. Multi Ch In Setup
3. ZONE Audio Setup

4. Power ON Level Setup

5. Volume Limit Setup

6. Remote Control Mode Setup
7. Flicker Reduction Setup
Exit Return
2 Select the volume level setting of ZONE 2
ZONE 3 (VSX-9140TXH only)
• Variable – Use this setting if you've connected a
power amplifier in the sub room (this receiver is
simply being used as a pre-amp) and you will be
using this receiver's controls to adjust the volume.
• Fixed – Use this setting if you've connected a fully
integrated amplifier (such as another Pioneer VSX
receiver) in the sub room and want to use that
receiver's volume controls.
With the Fixed setting, the source is sent from this
receiver at maximum volume, so make sure the volume is
quite low in the sub zone at first, and then experiment to
find the correct level.
3 When you're finished, press RETURN.
You will return to the Other Setup menu.
Note
1 If you selected ZONE 2 in the Surround back speaker setting on page 91, you won't be able to change the volume level.
+10dB
DVD
Finish
4d3.ZONE Audio Setup
A/V RECEIVER
ZONE 2 Volume Level : Variable
ZONE 3 Volume Level : Variable
Exit Finish
1
and
.
Power ON Level Setup
The volume can be set so that it is always set to the same
level when the receiver's power is turned on.
1 Select 'Power ON Level Setup' from the Other
Setup menu.
4d.Other Setup
A/V RECEIVER
1. KURO LINK Setup
2. Multi Ch In Setup
3. ZONE Audio Setup
4. Power ON Level Setup
5. Volume Limit Setup
6. Remote Control Mode Setup
7. Flicker Reduction Setup
Exit Return
2 Select the Power ON Level setting you want.
• LAST – When the power is turned on, the volume is
set to the same level as when the power was last
turned off.
• "---" – When the power is turned on, the volume is set
to minimum level.
• –80.0dB to +12.0dB – Specify the volume to be set
when the power is turned, in steps of 0.5 dB.
It is not possible to set a volume level greater than the
value specified at Volume Limit Setup.
3 When you're finished, press RETURN.
You will return to the Other Setup menu.
Volume Limit Setup
Use this function to limit the maximum volume. The
volume cannot be increased above the level set here,
even by operating MASTER VOLUME button (or the dial
on the front panel).
1 Select 'Volume Limit Setup' from the Other Setup
menu.
4d.Other Setup
A/V RECEIVER
1. KURO LINK Setup
2. Multi Ch In Setup
3. ZONE Audio Setup
4. Power ON Level Setup
5. Volume Limit Setup
6. Remote Control Mode Setup
7. Flicker Reduction Setup
Exit Return
2 Select the Volume Limit setting you want.
• OFF – The maximum volume is not limited.
• –20.0dB/–10.0dB/0.0dB – The maximum volume is
limited to the value set here.
3 When you're finished, press RETURN.
You will return to the Other Setup menu.
4d4.Power ON Level Setup
A/V RECEIVER
Power ON Level : LAST
Exit Finish
4d5.Volume Limit Setup
A/V RECEIVER
Volume Limit : OFF
Exit Finish
11
95
En