Page 1 2005 Cadillac Escalade/Escalade ESV Owner Manual Seats and Restraint Systems ......1-1 Driving Your Vehicle ........4-1 Your Driving, the Road, and Your Vehicle Front Seats ..4-2 ..........1-3 Towing Rear Seats ........... 4-53 ..........1-8 Safety Belts ..........1-28 Service and Appearance Care ......
Page 2: How To Use This Manual
Detroit, MI 48207 GENERAL MOTORS, GM, the GM Emblem, CADILLAC, How to Use This Manual the CADILLAC Crest & Wreath, and the names ESCALADE ESCALADE/ESV are registered trademarks Many people read the owner manual from beginning to of General Motors Corporation.
Page 3 Safety Warnings and Symbols You will also ﬁnd a circle with a slash through it in this book. This safety There are a number of safety cautions in this book. We symbol means “Do Not,” use a box and the word CAUTION to tell about things “Do Not do this”...
Page 4 Vehicle Damage Warnings Vehicle Symbols Also, in this manual you will ﬁnd these notices: The vehicle has components and labels that use symbols instead of text. Symbols are shown along Notice: These mean there is something that could with the text describing the operation or information damage your vehicle.
Page 5 These are some examples of symbols that may be found on the vehicle:...
Page 6 NOTES...
Page 7: Table Of Contents
Section 1 Seats and Restraint Systems Front Seats ............1-3 Center Passenger Position ......1-41 Power Seats ..........1-3 Rear Seat Passengers ........1-42 Power Lumbar ..........1-4 Rear Safety Belt Comfort Guides for Children Heated Seats ..........1-4 and Small Adults ........1-45 Heated and Cooled Seats ........1-5 Safety Belt Extender ........1-47 Reclining Seatbacks ........1-6 Child Restraints ..........1-48...
Page 8 Section 1 Seats and Restraint Systems Airbag System ..........1-72 Restraint System Check ........1-86 Where Are the Airbags? ........1-74 Checking Your Restraint Systems ....1-86 When Should an Airbag Inﬂate? .....1-77 Replacing Restraint System Parts What Makes an Airbag Inﬂate? .......1-78 After a Crash ..........1-87 How Does an Airbag Restrain? .......1-78 What Will You See After an Airbag Inﬂates? ..1-79 Passenger Sensing System ......1-80...
Page 9: Front Seats
Front Seats Horizontal Control: This control adjusts the seat cushion. • Raise or lower the front of the seat by raising or Power Seats lowering the forward edge of the control. Raise or lower the rear of the seat by raising or lowering the rear edge of the control.
Page 10: Power Lumbar
Power Lumbar To increase support, press and hold the top of the control. To decrease support, press and hold the bottom of the control. Let go of the control when the lower Your vehicle’s seats may be equipped with power seatback reaches the desired level of support.
Page 11 Heated and Cooled Seats The low setting warms the seatback and cushion until the seat temperature is near body temperature. The medium and high settings heat the seatback and seat cushion to a slightly higher temperature. You will be able to feel heat in about two minutes.
Page 12: Reclining Seatbacks
Reclining Seatbacks To operate the heated and cooled seats, do the following: Your vehicle’s front seatbacks have a recline feature 1. Press the red heat button (A) or the blue cool which is described earlier. See Power Seats on button (B). page 1-3.
Page 13: Head Restraints
Head Restraints CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can not do their job when you are reclined like this. The shoulder belt can not do its job. In a crash, you could go into it, receiving neck or other injuries.
Page 14: Rear Seats
Rear Seats The front head restraints can also be tilted forward in addition to being slid up or down. To tilt either of the front head restraints do the following: Rear Seat Operation Pull the head restraint toward you until you hear a click. Then let go.
Page 15 Be sure to return the seat to the passenger position when ﬁnished. Pull forward and push rearward on the CAUTION: seat to make sure it is locked in place. Escalade ESV: The passenger’s side of the second If the seatback is not locked, it could move row 60/40 or rear bucket seat has an easy entry/exit forward in a sudden stop or crash.
Page 16 Heated Seats Heated and Cooled Seats If your vehicle has this Your vehicle may be feature, the buttons used equipped with this feature. to control this feature The buttons used to are located on the back of control this feature are the center console.
Page 17 Folding the Seatbacks (60/40 Split To operate the heated and cooled seats, do the following: Bench Seat) 1. Press the red heat button (A) or the blue cool The rear seat may have a 60/40 split seat which may be button (B).
Page 18 Once the seatbacks are folded down, on Escalade ESV models only, the rear seat footwell area will be exposed and will have to be covered by the load ﬂoor panel(s). To create a load ﬂoor, do the following: Escalade ESV: On the passenger side of Escalade ESV models, the lever at the base of the seat must be pulled up to release the seatback.
Page 19 Returning the Seats to an Upright To return the seat to the upright position, do the following: Position 1. On Escalade ESV models, lift the load ﬂoor panels and latch them into the seatback. CAUTION: 2. Lift the seatback up and push it rearward all the way.
Page 20 Folding the Seatbacks To return the seatbacks to the passenger position, do To fold the seatbacks, do the following: the following: 1. Pull up on the release 1. Pull up on the release lever labeled 1 located lever labeled 1 and on the rear of the then pull up on seatback, and push the...
Page 21 Tilting the 50/50 Split Bench Seat Returning the Seat(s) to an Upright Position 1. Fold the seatbacks forward using the instructions listed previously. 2. Unlatch the seat from CAUTION: the ﬂoor by pulling up on the lever labeled 2 located on the rear If the seatback is not locked, it could move of the seat.
Page 22 Removing the 50/50 Split Bench Seats 2. While still holding the lever 3 toward you, grasp the top of the seat and pull it toward you slightly. To remove the 50/50 split bench seat, do the following: 3. Let go of lever 3 and pull the seat completely down. 1.
Page 23 3. To unlatch the rear of the seat from the ﬂoor, pull up on the release lever labeled 2 at the rear of the seat, and lift the rear of the seat up from the ﬂoor. 4. Squeeze the release handle while pulling the seat out.
Page 24 Replacing the 50/50 Split Bench Seat CAUTION: CAUTION: A safety belt that is improperly routed, not properly attached, or twisted will not provide If the seatback is not locked, it could move the protection needed in a crash. The person forward in a sudden stop or crash.
Page 25: Bench Seat
Folding the Seatback 2. Once the latches are engaged, let the seat drop into place. Release the lever CAUTION: labeled 1 and pull the seatback up using the assist strap on the If the seatback is not locked, it could move outboard side of the forward in a sudden stop or crash.
Page 26 Unfolding the Seatback Tilting the Full Bench Seat 1. To return the seatback to an upright position, CAUTION: pull up on the release lever labeled 1 and then pull up on the seatback If the seatback is not locked, it could move until it locks into the forward in a sudden stop or crash.
Page 27 3. Lift the rear of the seat up from the ﬂoor and push it 4. While holding the seat forward. You will not be able to unlatch the seat forward, pull the from the ﬂoor unless the seatback is folded down. support rod out from the retainer clips and ﬂip it down until it...
Page 28 Returning the Seat to an Upright Removing the Bench Seat Position To remove the bench seat, do the following: To return the seatback to the upright position, do the 1. Open the liftgate. following: 2. Fold the seatback 1. Pull the lever on the forward onto the seat support rod bracket cushion by using...
Page 29 3. To unlatch the rear of 4. Pull on the release the seat from the ﬂoor, strap located in the pull up on the release lower middle of lever labeled 2 at the seat to unlatch the the rear of the seat and seat from the ﬂoor lift the rear of the and pull the seat out.
Page 30 Replacing the Bench Seat CAUTION: CAUTION: A safety belt that is improperly routed, not properly attached, or twisted will not provide If the seatback is not locked, it could move the protection needed in a crash. The person forward in a sudden stop or crash. That could wearing the belt could be seriously injured.
Page 31: Bucket Seats
Bucket Seats Folding the Seatbacks The seatbacks on the bucket seats may be folded If your vehicle has bucket seats, the seatbacks can be forward to give you more cargo space. reclined and the seats can be folded to give you more cargo room.
Page 32 2. Pull the seatback release lever upward and pull the seatback up and fold it down until it is ﬂat. Escalade lever shown, Escalade ESV lever similar. On the Escalade ESV models, ﬁrst remove the headrest and store it on the top of the seat cushion as shown next.
Page 33 Returning the Seatbacks to an Upright Once the seatbacks are folded down, on Escalade ESV models only, the rear seat footwell area will be Position exposed and will have to be covered by the load ﬂoor panel. To create a load ﬂoor, do the following: CAUTION: If the seatback is not locked, it could move forward in a sudden stop or crash.
Page 34: Safety Belts
Safety Belts CAUTION: Safety Belts: They Are for Everyone It is extremely dangerous to ride in a cargo This part of the manual tells you how to use safety area, inside or outside of a vehicle. In a belts properly. It also tells you some things you should collision, people riding in these areas are more not do with safety belts.
Page 35: Why Safety Belts Work
Why Safety Belts Work A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not When you ride in or on anything, you go as fast survive. But most crashes are in between. In many of as it goes.
Page 36 Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. 1-30...
Page 37 The person keeps going until stopped by something. In or the instrument panel... a real vehicle, it could be the windshield... 1-31...
Page 38: Questions And Answers About Safety Belts
Questions and Answers About Safety Belts Will I be trapped in the vehicle after an accident if I am wearing a safety belt? You could be — whether you are wearing a safety belt or not. But you can unbuckle a safety belt, even if you are upside down.
Page 39: Driver Position
Driver Position If I am a good driver, and I never drive far from home, why should I wear safety belts? Lap-Shoulder Belt You may be an excellent driver, but if you are in an The driver has a lap-shoulder belt. Here is how to wear accident —...
Page 40 4. Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure. If the belt is not long enough, see Safety Belt Extender on page 1-47. Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to.
Page 41 What is wrong with this? CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should ﬁt against your body. The shoulder belt is too loose. It will not give nearly as much protection this way.
Page 42 What is wrong with this? CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones.
Page 43 What is wrong with this? CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied at the abdomen, not at the pelvic bones, and that could cause serious or fatal injuries.
Page 44 What is wrong with this? CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury. Also, the belt would apply too much force to the ribs, which are not as strong as shoulder bones.
Page 45 What wrong with this? CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to ﬁx it.
Page 46: Safety Belt Use During Pregnancy
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. To unlatch the belt, just push the button on the buckle. The belt should go back out of the way.
Page 47: Right Front Passenger Position
Right Front Passenger Position Third Row — Lap Belt To learn how to wear the right front passenger’s safety belt properly, see Driver Position on page 1-33. The right front passenger’s safety belt works the same way as the driver’s safety belt — except for one thing.
Page 48: Rear Seat Passengers
Rear Seat Passengers It is very important for rear seat passengers to buckle up! Accident statistics show that unbelted people in the rear seat are hurt more often in crashes than those who are wearing safety belts. Rear passengers who are not safety belted can be thrown out of the vehicle in a crash.
Page 49 2. Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure. When the shoulder belt is pulled out all the way, it will lock. If it does, let it go back all the way and start again.
Page 50 The safety belt locks if there is a sudden stop or a crash. CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should ﬁt against your body. The lap part of the belt should be worn low and snug on the hips, just touching the thighs.
Page 51: Rear Safety Belt Comfort Guides For Children
There is one guide for each passenger position in the rear seats. Here is how to install a comfort guide and use the safety belt: To unlatch the belt, just push the button on the buckle. Rear Safety Belt Comfort Guides Second Row Seat for Children and Small Adults 1.
Page 52 Third Row Seat 2. Place the guide over the belt and insert the two edges of the belt into the slots of the guide. For the third row, remove the guide from its storage clip on the side of the seatback. 3.
Page 53: Safety Belt Extender
Safety Belt Extender If the vehicle’s safety belt will fasten around you, you should use it. But if a safety belt is not long enough, your dealer will order you an extender. It is free. When you go in to order it, take the heaviest coat you will wear, so the extender will be long enough for you.
Page 54: Child Restraints
Child Restraints What is the proper way to wear safety belts? If possible, an older child should wear a Older Children lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should ﬁt snugly below the hips, just touching the top of the thighs.
Page 55 What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt is very close to the child’s face or neck? If the child is sitting in a rear seat outside position, move the child toward the center of the vehicle. If the child is sitting in the center position, move the child toward the safety belt buckle.
Page 56: Infants And Young Children
Wherever the child sits, the lap portion of the belt should be worn low and snug on the hips, just touching the child’s thighs. This applies belt force to the child’s pelvic bones in a crash. Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children.
Page 57 CAUTION: People should never hold a baby in their arms while riding in a vehicle. A baby does not weigh much — until a crash. During a crash a baby will become so heavy it is not possible to hold it. For example, in a crash at only 25 mph (40 km/h), a 12 lb (5.5 kg) baby will suddenly become a 240 lb (110 kg) force on a person’s arms.
Page 58 CAUTION: Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them.
Page 59 For most basic types of child restraints, there are many different models available. When purchasing a CAUTION: child restraint, be sure it is designed to be used in a motor vehicle. If it is, the restraint will have a label saying that it meets federal motor vehicle The body structure of a young child is quite safety standards.
Page 60: Child Restraint Systems
Child Restraint Systems A rear-facing infant seat (B) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, An infant car bed (A), a special bed made for use in a acts to keep the infant positioned in the restraint.
Page 61 A forward-facing child seat (C-E) provides restraint for A booster seat (F-G) is a child restraint designed to the child’s body with the harness and also sometimes improve the ﬁt of the vehicle’s safety belt system. Some with surfaces such as T-shaped or shelf-like shields. booster seats have a shoulder belt positioner, and some high-back booster seats have a ﬁve-point harness.
Page 62 When choosing a child restraint, be sure the child How do child restraints work? restraint is designed to be used in a vehicle. If it is, it will have a label saying that it meets federal motor A child restraint system is any device designed for vehicle safety standards.
Page 63: Where To Put The Restraint
Where to Put the Restraint CAUTION: (Continued) Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. Even though the passenger sensing system is General Motors recommends that child restraints be secured in a rear seat, including an infant riding in a designed to turn off the passenger’s frontal rear-facing infant seat, a child riding in a forward-facing airbag if the system detects a rear-facing child...
Page 64: Top Strap
Top Strap Some child restraints have a top strap, or “top tether.” It can help restrain the child restraint during a collision. For it to work, a top strap must be properly anchored to the vehicle. Some top strap-equipped child restraints are designed for use with or without the top strap being anchored.
Page 65 Anchor the top strap to one of the following anchor points. Be sure to use an anchor point located on the CAUTION: same side of the vehicle as the seating position where the child restraint will be placed. Each top tether bracket is designed to anchor Raise the head restraint and route the top strap under only one child restraint.
Page 66: Top Strap Anchor Location
Top Strap Anchor Location Escalade ESV A child restraint with a top strap should only be used in the second or third row. Do not secure a child restraint in the right front passenger’s position or the third row outboard seating positions if a national or local law requires that the top strap be anchored, or if the instructions that come with the child restraint say that the top strap must...
Page 67 Escalade A child restraint with a top strap should only be used in the second or third row. Do not secure a child restraint in the right front passenger’s position or the third row driver’s-side and center seating positions if a national or local law requires that the top strap be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored.
Page 68: Lower Anchorages And Top Tethers For Children (Latch System)
Lower Anchorages and Top Tethers for Children (LATCH System) Your vehicle has the LATCH system. You will ﬁnd anchors in the center and right side passenger second row seating positions for bench seats and the outboard passenger positions for bucket seats. This system, designed to make installation of child restraints easier, does not use the vehicle’s safety belts.
Page 69 A. Lower Anchorage A. Lower Anchorage B. Lower Anchorage B. Lower Anchorage C. Top Tether In order to use the LATCH system in your vehicle, you need a child restraint designed for that system. 1-63...
Page 70: Securing A Child Restraint Designed For The Latch System
Securing a Child Restraint Designed To assist you in locating the lower anchors for this child restraint system, each seating position with the for the LATCH System LATCH system has a visible metal anchorage point in the seat where the seatback meets the seat cushion. 1.
Page 71: Securing A Child Restraint In A Rear Outside
Securing a Child Restraint in a Rear Outside Seat Position If your child restraint is equipped with the LATCH system, see Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-62. See Top Strap on page 1-58 if the child restraint has one. For the third row, if your vehicle has a bench seat, there are no top strap anchors in the outboard seating positions.
Page 72 4. Pull the rest of the shoulder belt all the way out of 5. To tighten the belt, push down on the child restraint, the retractor to set the lock. pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
Page 73: Securing A Child Restraint In A Center Rear
Securing a Child Restraint in a If your child restraint does not have the LATCH system, you will be using a lap belt to secure the child restraint Center Rear Seat Position in the center seat position in the third row. Be sure to follow the instructions that came with the child Second Row restraint.
Page 74: Securing A Child Restraint In The Right Front
Securing a Child Restraint in the Right Front Seat Position Your vehicle has a right front passenger air bag. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 1-57. In addition, your vehicle may have the passenger sensing system.
Page 75 You will be using the lap-shoulder belt to secure the child restraint in this position. See Top Strap on CAUTION: page 1-58 if your child restraint has one. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as A child in a rear-facing child restraint can be the instructions say.
Page 76 4. Buckle the belt. Make sure the release button is 5. Pull the rest of the shoulder belt all the way out of positioned so you would be able to unbuckle the the retractor to set the lock. safety belt quickly if you ever had to. 1-70...
Page 77 8. If your vehicle has the passenger sensing system and the air bag is off, the off indicator will be lit and stay lit in the inside rearview mirror when the key is turned to RUN or START. If a child restraint has been installed and the on indicator is lit, turn the vehicle off.
Page 78: Airbag System
Airbag System CAUTION: (Continued) Your vehicle has four airbags — a frontal airbag for the driver, another frontal airbag for the right front Frontal airbags for the driver and right front passenger, a side impact airbag for the driver, and passenger are designed to deploy only in another side impact airbag for the right front passenger.
Page 79 CAUTION: CAUTION: Both frontal and side impact airbags inﬂate Anyone who is up against, or very close to, with great force, faster than the blink of an any airbag when it inﬂates can be seriously eye. If you are too close to an inﬂating airbag, injured or killed.
Page 80: Where Are The Airbags
Where Are the Airbags? There is an airbag readiness light on the instrument panel cluster, which shows the airbag symbol. The system checks the airbag electrical system for malfunctions. The light tells you if there is an electrical problem. See Airbag Readiness Light on page 3-34 for more information.
Page 81 The right front passenger’s frontal airbag is in the The driver’s side impact airbag is in the side of the instrument panel on the passenger’s side. driver’s seatback closest to the door. 1-75...
Page 82 CAUTION: If something is between an occupant and an airbag, the airbag might not inﬂate properly or it might force the object into that person causing severe injury or even death. The path of an inﬂating airbag must be kept clear. Do not put anything between an occupant and an airbag, and do not attach or put anything on the steering wheel hub or on or near any other...
Page 83: When Should An Airbag Inﬂate
When Should an Airbag Inﬂate? 20 to 30 mph (32 to 48 km/h). (The threshold level can vary, however, with speciﬁc vehicle design, so that it can be somewhat above or below this range.) The driver’s and right front passenger’s frontal airbags are designed to inﬂate in moderate to severe frontal Airbags may inﬂate at different crash speeds.
Page 84: What Makes An Airbag Inﬂate
What Makes an Airbag Inﬂate? Side impact airbags are designed to inﬂate in moderate to severe side crashes. A side impact airbag will inﬂate if the crash severity is above the system’s In an impact of sufficient severity, the airbag sensing designed “threshold level.”...
Page 85: What Will You See After An Airbag Inﬂates
Airbags should never be regarded as anything more than a supplement to safety belts, and then only in moderate CAUTION: to severe frontal or near-frontal collisions for the driver’s and right front passenger’s frontal airbags, and only in moderate to severe side collisions for vehicles with a When an airbag inﬂates, there is dust in the driver’s and right front passenger’s side impact airbag.
Page 86: Passenger Sensing System
In many crashes severe enough to inﬂate an airbag, Notice: If you damage the covering for the driver’s windshields are broken by vehicle deformation. or the right front passenger’s airbag, or the airbag Additional windshield breakage may also occur from the covering on the driver’s and right front passenger’s right front passenger airbag.
Page 87 The passenger sensing system works with sensors that are part of the right front passenger’s seat and safety belt. The sensors are designed to detect the presence of a properly-seated occupant and determine if the passenger’s frontal airbag should be enabled (may inﬂate) or not.
Page 88 Your vehicle has a rear seat that will accommodate a The passenger sensing system is designed to turn off rear-facing child restraint. A label on your sun visor says, the right front passenger’s frontal airbag if: “Never put a rear-facing child seat in the front.” This •...
Page 89 If after reinstalling the child restraint and restarting the For some children who have outgrown child restraints vehicle, the on indicator is still lit, check to make and for very small adults, the passenger sensing system sure that the vehicle’s seatback is not pressing the child may or may not turn off the right front passenger’s restraint into the seat cushion.
Page 90 CAUTION: If the airbag readiness light in the instrument panel cluster ever comes on and stays on, it means that something may be wrong with the airbag system. If this ever happens, have the vehicle serviced promptly, because an adult-size person sitting in the right front passenger’s seat may not have the protection of the frontal airbag.
Page 91: Servicing Your Airbag-Equipped Vehicle
Servicing Your Airbag-Equipped Aftermarket equipment, such as seat covers, can affect how well the passenger sensing system operates. Vehicle You may want to consider not using seat covers or other aftermarket equipment if your vehicle has the passenger Airbags affect how your vehicle should be serviced. sensing system.
Page 92: Restraint System Check
Adding Equipment to Your Because I have a disability, I have to get my vehicle modiﬁed. How can I ﬁnd out whether Airbag-Equipped Vehicle this will affect my advanced airbag system? Changing or moving any parts of the front seats, Is there anything I might add to the front or safety belts, the airbag sensing and diagnostic sides of the vehicle that could keep the...
Page 93: Replacing Restraint System Parts
Torn or frayed safety belts may not protect you in a If you have had a crash, do you need new belts or crash. They can rip apart under impact forces. If a belt LATCH system parts? is torn or frayed, get a new one right away. After a very minor collision, nothing may be necessary.
Page 94 NOTES 1-88...
Page 95 Section 2 Features and Controls Keys ...............2-3 Adjustable Throttle and Brake Pedal ....2-20 Remote Keyless Entry System ......2-4 Engine Coolant Heater ........2-21 Remote Keyless Entry System Operation ...2-5 Automatic Transmission Operation ....2-22 Tow/Haul Mode ..........2-24 Doors and Locks ..........2-8 All-Wheel Drive ..........2-25 Door Locks ............2-8 Parking Brake ..........2-25 Power Door Locks ..........2-9...
Page 96 Section 2 Features and Controls ® HomeLink Transmitter ........2-37 Rear Seat Armrest ........2-43 ® Programming the HomeLink Transmitter ..2-37 Convenience Net ..........2-43 Cargo Cover ..........2-44 Storage Areas ..........2-41 Glove Box ...........2-41 Sunroof ............2-45 Cupholder(s) ..........2-41 Vehicle Personalization ........2-46 Instrument Panel Storage Area .......2-41 Memory Seat ..........2-46 Center Console Storage Area ......2-42 Luggage Carrier ...........2-42...
Page 97: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. They could operate the power windows or other controls or even make the vehicle move. The children or others could be badly injured or even killed.
Page 98: Remote Keyless Entry System
1. This device may not cause interference, and ® 2. This device must accept any interference received, In an emergency contact Cadillac Roadside Service including interference that may cause undesired See Roadside Service on page 7-6 for more information. operation of the device.
Page 99: Remote Keyless Entry System Operation
Remote Keyless Entry System At times you may notice a decrease in range. This is normal for any remote keyless entry system. If the Operation transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this: You can lock and unlock your doors from about •...
Page 100: Battery Replacement
Battery Replacement (Lock): Press this button once to lock all of the doors. Pressing lock again within three seconds Under normal use, the battery in your remote keyless may cause the horn to chirp for lock conﬁrmation. You entry transmitter should last about two years. can choose different feedback options for each press of the lock button.
Page 101 To replace the battery in the keyless entry transmitter, 3. Align the covers and snap them together. do the following: 4. Resynchronize the transmitter. See “Resynchronization” following this information. 5. Check the operation of the transmitter. Resynchronization Resynchronization may be necessary due to the security method used by this system.
Page 102: Doors And Locks
Doors and Locks There are several ways to lock and unlock your vehicle. To unlock the door from the outside, use the keyless entry system or the key. Door Locks To unlock or lock the door from the inside, slide the manual lever forward CAUTION: or rearward.
Page 103: Power Door Locks
Power Door Locks Delayed Locking When locking the doors with the power lock switch or The power door lock the keyless entry transmitter and a door or the liftgate (if switches are located on equipped) is open, the delayed locking feature will the driver’s and front delay locking the doors until ﬁve seconds after the last passenger’s armrests.
Page 104: Programmable Automatic Door Locks
Programmable Automatic Door 2. Turn the key to RUN then back to LOCK twice. Then, with the key in LOCK, release the turn Locks signal/multifunction lever. Once you do this, the doors will lock and unlock, the horn will chirp twice, Your vehicle is equipped with an automatic lock/unlock and a 30-second timer will begin.
Page 105 Programmable Unlocking Feature 2. Turn the key to RUN and LOCK twice. Then, with the key in LOCK, release the turn The following is the list of available programming signal/multifunction lever. Once you do this, the options: doors will lock and unlock, the horn will chirp twice, and a 30-second timer will begin.
Page 106: Rear Door Security Locks
Rear Door Security Locks The rear doors cannot be opened from the inside when this feature is in use. If you want to open the rear door while the security lock is engaged, unlock the door With this feature, you can lock the rear doors so they and open the door from the outside.
Page 107: Liftgate/Liftglass
Liftgate/Liftglass To unlock the liftgate and liftgate glass from the outside use either the power door locks or the remote keyless entry system. The liftgate glass can be opened using the pushbutton CAUTION: on the liftgate after the doors have been unlocked. To open the entire liftgate, lift the handle located in the It can be dangerous to drive with the liftgate or center of the door.
Page 108: Windows
Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 109: Power Windows
Power Windows Express-Down Windows The driver and front passenger windows also have an express-down feature that allows the windows to be lowered without holding the switch. Press down fully on the window switch, then release, to activate the express-down mode. This mode can be canceled at any time by pulling up on the switch.
Page 110: Theft-Deterrent Systems
Theft-Deterrent Systems 3. Close all doors. The security light should go off after about 30 seconds. The alarm is not armed until the security light goes off. Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent If a locked door is opened without the key or the remote features, we know that nothing we put on it can make it keyless entry transmitter, the alarm will go off.
Page 111: Passlock
® Passlock If you set off the alarm by accident, unlock any door with the key. You can also turn off the alarm by pressing ® unlock on the remote keyless entry transmitter. The alarm Your vehicle is equipped with the Passlock won’t stop if you try to unlock a door any other way.
Page 112: Starting And Operating Your Vehicle
Starting and Operating Your Ignition Positions Vehicle New Vehicle Break-In Notice: Your vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: • Keep your speed at 55 mph (88 km/h) or less for the ﬁrst 500 miles (805 km).
Page 113: Retained Accessory Power (Rap)
B (Accessory): This position lets you use things Move your shift lever to PARK (P) or NEUTRAL (N). like the radio and the windshield wipers when the Your engine will not start in any other position — that is engine is off. a safety feature.
Page 114: Adjustable Throttle And Brake Pedal
Adjustable Throttle and Brake Pedal When starting your engine in very cold weather (below 0°F or 18°C), do this: If your vehicle has this feature, you can change the 1. With your foot off the accelerator pedal, turn the position of the throttle and brake pedals. This feature is ignition key to START and hold it there up to designed for shorter drivers, since the pedals cannot 15 seconds.
Page 115: Engine Coolant Heater
Engine Coolant Heater CAUTION: Your vehicle may be equipped with an engine coolant heater. Plugging the cord into an ungrounded outlet In very cold weather, 0°F ( 18°C) or colder, the engine could cause an electrical shock. Also, the coolant heater can help. You will get easier starting and better fuel economy during engine warm-up.
Page 116: Automatic Transmission Operation
Automatic Transmission Operation CAUTION: Your vehicle is equipped with an automatic transmission and features an electronic shift position indicator located within the instrument panel cluster. It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the There are several different positions for your shift lever.
Page 117 To rock your vehicle back and forth to get out of snow, DRIVE (D): This position is for normal driving. If you ice or sand without damaging your transmission, need more power for passing, and you are: see If You Are Stuck: In Sand, Mud, Ice or Snow on •...
Page 118: Tow/Haul Mode
Tow/Haul Mode If you manually select SECOND (2), the transmission will drive in second gear. You may use this feature for reducing the speed of the rear wheels when you are trying to start your vehicle from a stop on slippery road surfaces.
Page 119: All-Wheel Drive
All-Wheel Drive With this feature, engine power is sent to all four wheels when extra traction is needed. This is like four-wheel drive, but there is no separate lever or switch to engage or disengage the front axle. It is fully automatic, and adjusts itself as needed for road conditions.
Page 120: Shifting Into Park (P)
Shifting Into Park (P) Leaving Your Vehicle With the Engine Running CAUTION: CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with It can be dangerous to leave your vehicle with the parking brake ﬁrmly set.
Page 121: Shifting Out Of Park (P)
Torque Lock Shifting Out of Park (P) If you are parking on a hill and you do not shift your Your vehicle has an automatic transmission shift lock vehicle into PARK (P) properly, the weight of the vehicle control system. You have to fully apply your regular may put too much force on the parking pawl in the brakes before you can shift from PARK (P) when the transmission.
Page 122: Parking Over Things That Burn
Parking Over Things That Burn Engine Exhaust CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: • Your exhaust system sounds strange or different.
Page 123: Running Your Engine While You Are Parked
Running Your Engine While You CAUTION: Are Parked It is better not to park with the engine running. But if It can be dangerous to get out of your vehicle you ever have to, here are some things to know. if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set.
Page 124: Mirrors
Mirrors Temperature and Compass Display Press the on/off button, located to the far left, brieﬂy to turn the compass/temperature display on or off. Automatic Dimming Rearview Mirror ® If the display reads CAL, the compass needs to with OnStar , Compass and be calibrated.
Page 125 Automatic Dimming Mirror Operation To adjust for compass variance, do the following: 1. Find your current location and variance zone The automatic dimming mirror function is turned number on the following zone map. on automatically each time the ignition is started. To operate the automatic dimming mirror, do the following: 1.
Page 126 3. Keep pressing the on/off button until the desired In order to calibrate, CAL must be displayed in the zone number appears in the display. Release the mirror compass windows. If CAL is not displayed, push button. After approximately four seconds of the on/off button for approximately 12 seconds or inactivity, the new zone number will be locked in until CAL is displayed.
Page 127: Outside Power Mirrors
Outside Power Mirrors Power Folding Mirrors To fold or unfold the mirrors, move the selector switch, The controls are located located above the mirror control, to the middle position. on the driver’s door The mirror control will illuminate. Press the right or left armrest.
Page 128: Outside Convex Mirror
Outside Convex Mirror Outside Heated Mirrors If the vehicle has heated mirrors, the button to turn CAUTION: this function on or off is located on the climate A convex mirror can make things (like other control panel. vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right.
Page 129: Outside Automatic Dimming Mirror With Curb View Assist
® Outside Automatic Dimming Mirror OnStar System with Curb View Assist ® OnStar uses global positioning system (GPS) satellite technology, wireless communications, and call centers Your vehicle may have this feature. to provide you with a wide range of safety, security, The driver’s outside mirror will adjust for the glare of information, and convenience services.
Page 130 ® Directions and Connections Plan OnStar Virtual Advisor • ® Automatic Notiﬁcation of Airbag Deployment Virtual Advisor is a feature of OnStar Personal Calling that uses minutes to access up-to-date weather and • Emergency Services traffic reports for your area, news and sports updates, •...
Page 131: Homelink Transmitter
® HomeLink Transmitter This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Page 132 Keep the original transmitter for use in other vehicles as 2. Position the end of your hand-held transmitter ® well as for future HomeLink programming. It is also about 1 to 3 inches (3 to 8 cm) away from the ®...
Page 133 Gate Operator and Canadian If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Programming Steps 6 through 8 following to complete the programming of a rolling-code equipped device Canadian radio-frequency laws require transmitter (most commonly, a garage door opener).
Page 134: Using Homelink
® ® Using HomeLink Reprogramming a Single HomeLink Button ® Press and hold the appropriate HomeLink button for at least half of a second. The indicator light will come ® ® To program a device to HomeLink using a HomeLink on while the signal is being transmitted.
Page 135: Storage Areas
Storage Areas Perform the following procedure to use your front cupholders: 1. Place the provided beverage container in the Glove Box cup holder. 2. Press the top (red dot) of the switch to heat the cup Open the glove box by pulling the bottom of the holder or press the bottom (blue dot) of the switch handle upward.
Page 136: Center Console Storage Area
Center Console Storage Area Don’t exceed the maximum vehicle capacity when loading your vehicle. For more information on vehicle capacity and loading, see Loading Your Vehicle on Your vehicle has a console compartment between the page 4-47. bucket seats. To prevent damage or loss of cargo as you’re leaving, To open it, press the button on the side of the console check now and then to make sure the luggage and and swing the console lid open.
Page 137: Rear Seat Armrest
• Convenience Net If you need to carry long items, move the crossrails as far apart as they will go. Tie the load to the The convenience net (if equipped) in the rear of your crossrails and the siderails or siderail supports. Also vehicle helps to keep small loads in place during sharp tie the load to the bumpers.
Page 138: Cargo Cover
Cargo Cover To return the cover to the retracted position, do the following: 1. Pull up on the cover handle to release the cover posts from the retaining sockets. CAUTION: 2. Let the cover move forward to the full retracted position.
Page 139: Sunroof
Sunroof 3. Move the other end of the cover forward and hold it next to the passenger’s side trim panel slot. 4. Push the button on top of the passenger’s side endcap. This will allow the cover to extend into the trim slot.
Page 140: Vehicle Personalization
Vehicle Personalization The sunroof is also equipped with a sunshade which you can pull forward to block sun rays. If a hand, arm, or other object is blocking the sunroof Memory Seat glass panel as it is closing, the glass panel will stop at the obstruction.
Page 141 2. Press and hold the 1 or 2 button of the memory To store the seat exit position, do the following: control for three seconds. A double chime will 1. Press and release the 1 or 2 button. The seat will sound to let you know that the position has move to the stored memory position.
Page 142 NOTES 2-48...
Page 143 Section 3 Instrument Panel Instrument Panel Overview .......3-4 Ultrasonic Rear Parking Assist (URPA) ....3-18 Hazard Warning Flashers ........3-6 Accessory Power Outlets .......3-21 Other Warning Devices ........3-6 Ashtrays and Cigarette Lighter ......3-21 Horn .............3-6 Analog Clock ..........3-22 Tilt Wheel .............3-7 Climate Controls ..........3-22 Turn Signal/Multifunction Lever ......3-7 Dual Automatic Climate Control System ...3-22 Turn and Lane-Change Signals ......3-8...
Page 144 Section 3 Instrument Panel Engine Coolant Temperature Gage ....3-40 Navigation/Radio System .......3-96 Transmission Temperature Gage .....3-41 Rear Seat Audio (RSA) .........3-97 Malfunction Indicator Lamp ......3-42 CD Changer ..........3-99 Oil Pressure Gage ........3-45 Theft-Deterrent Feature ........3-102 Security Light ..........3-46 Audio Steering Wheel Controls ......3-102 Cruise Control Light ........3-47 Radio Reception .........3-103 Highbeam On Light ........3-47...
Page 145 NOTES...
Page 146: Instrument Panel Overview
Instrument Panel Overview...
Page 147 The main components of your instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 3-28. K. Driver Information Center (DIC) Buttons. See Driver Information Center (DIC) on page 3-49. B. Exterior Lamps Control. See Exterior Lamps on page 3-14.
Page 148: Hazard Warning Flashers
Hazard Warning Flashers Press the button to make the front and rear turn signal lamps ﬂash on and off. Press the button again to turn the ﬂashers off. Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front When the hazard warning ﬂashers are on, your turn and rear turn signal lamps will ﬂash on and off.
Page 149: Tilt Wheel
Tilt Wheel Turn Signal/Multifunction Lever The tilt steering wheel allows you to adjust the steering wheel before you drive. You can raise it to the highest level to give your legs more room when you enter and exit the vehicle. The lever on the left side of the steering column includes the following: •...
Page 150: Turn And Lane-Change Signals
As you signal a turn or a lane change, if the arrows • Windshield Washer. See Windshield Washer ﬂash more quickly than normal, a signal bulb may on page 3-10. be burned out and other drivers won’t see your turn •...
Page 151: Flash-To-Pass
Windshield Wipers When the high beams are on, this indicator light on the instrument panel You control the windshield wipers by turning the band cluster will also be on. with the wiper symbol on it. (Mist): For a single wiping cycle, turn the band to mist.
Page 152: Windshield Washer
Windshield Washer Rear Window Washer/Wiper If your vehicle has a rear (Washer Fluid): There is a paddle marked with the window washer/wiper, this windshield washer symbol at the top of the multifunction knob is located on the lever. To spray washer ﬂuid on the windshield, push instrument panel to the left the paddle.
Page 153: Cruise Control
Cruise Control If you apply your brakes, the cruise control will shut off. (Off): This position CAUTION: turns the system off. Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic.
Page 154 Setting Cruise Control Resuming a Set Speed Suppose you set your cruise control at a desired speed and then you apply the brake. This, of course, CAUTION: disengages the cruise control. But you do not need to reset it. If you leave your cruise control on when you Once you’re going about 25 mph (40 km/h) or more, you are not using cruise, you might hit a button can move the cruise control switch brieﬂy from on to...
Page 155 • When going downhill, you may have to brake or shift to Move the cruise switch from on to a lower gear to keep your speed down. Of course, resume/accelerate. Hold it there until you get up to applying the brake takes you out of cruise control. Many the speed you want, and then release the switch.
Page 156: Exterior Lamps
Exterior Lamps AUTO: Turn the control to this position to put the system into automatic headlamp mode. The Daytime Running Lamps (DRL) will also be activated if it is light enough outside. (Parking Lamps): Turn the control to this position to turn on the parking lamps, together with the following: •...
Page 157: Headlamps On Reminder
Headlamps on Reminder When the DRL are on, only your DRL lamps will be on. The taillamps, sidemarker and other lamps won’t be on. The instrument panel won’t be lit up either. If a door is open, a reminder chime will sound when your headlamps or parking lamps are manually turned on and When it begins to get dark, the automatic headlamp your key is out of the ignition.
Page 158: Fog Lamps
Fog Lamps Your vehicle has a light sensor located on the top of the instrument panel. Be sure it is not covered, or the system will be on whenever the ignition is on. If your vehicle has fog lamps you can use them for better vision in foggy or misty conditions.
Page 159: Instrument Panel Brightness
Dome Lamps The fog lamps will go off whenever your high-beam headlamps come on. When the high beams go off, the fog lamps will come on again. The dome lamps will come on when you open a door or the midgate, if equipped, and will turn off when The fog lamps will be cancelled after the ignition is all doors or midgate are closed.
Page 160: Reading Lamps
Reading Lamps Battery Run-Down Protection This feature shuts off the dome lamps if they are left on If your vehicle has reading for more than 10 minutes when the ignition is in lock. lamps, press the button This will keep your battery from running down. located next to the lamp to turn it on or off.
Page 161 The URPA display is located inside the vehicle, CAUTION: near the rear window. It has three color-coded lights used to provide Even with the Ultrasonic Rear Park Assist distance and system system, the driver must check carefully before information to the driver. backing up.
Page 162 How the System Works When the System Does Not Seem to Work Properly Unless disabled, the URPA will turn on automatically when the shift lever is moved into REVERSE (R). When The light may ﬂash red when the vehicle is in the system turns on, the three lights on the display REVERSE (R) if the ultrasonic sensors are not kept will illuminate for one and a half seconds to let you know...
Page 163: Accessory Power Outlets
Accessory Power Outlets Notice: Improper use of the power outlet can cause damage not covered by your warranty. Do not hang any type of accessory or accessory bracket With accessory power outlets you can plug in auxiliary from the plug because the power outlets are electrical equipment such as a cellular telephone designed for accessory power plugs only.
Page 164: Analog Clock
Analog Clock Climate Controls To adjust the clock, do the following: Dual Automatic Climate Control 1. Locate the adjustment button to the lower left corner of the clock. System 2. Push and hold the adjustment button to advance With this system, you can control the heating, cooling the clock hands.
Page 165 Driver’s Side Temperature Knob The passenger’s temperature setting can be set to match the driver’s temperature setting by pressing and The driver’s side knob is used to adjust the temperature holding the AUTO button for four seconds. Both the of the air coming through the system on the driver’s driver and passenger arrows will be displayed.
Page 166 If the driver’s and passenger’s temperature settings Be careful not to cover the sensor located on the are not the same, the opposite side temperature top of the instrument panel near the windshield. This setting will be displayed for an additional ﬁve sensor regulates air temperature based on sun seconds.
Page 167: Manual Operation
Manual Operation (Panel): This setting will deliver air to the instrument panel outlets. You may manually adjust the air delivery mode or fan speed. (Bi-Level): This setting will deliver warmer air to the ﬂoor and cooler air to the instrument panel outlets. (Fan): The switch with the fan symbol allows you to manually adjust the fan speed.
Page 168 If you select recirculation while in defrost, defog or ﬂoor, Pressing this button when the outside temperature is the light in the button will ﬂash and then go out to let you too cool for air conditioning to be effective will make the know that this is not allowed.
Page 169: Defogging And Defrosting
Defogging and Defrosting On cool, but sunny days while using manual operation of the automatic system, use bi-level to deliver warm air to You can use either defog or front defrost to clear fog or the ﬂoor and cooler air to the instrument panel outlets. frost from your windshield.
Page 170: Outlet Adjustment
Rear Window Defogger Outlet Adjustment If your vehicle has this feature, the lines you see on the Your vehicle has air outlets located in the center and on rear window warm the glass. The rear window defogger the side of your instrument panel that allow you to adjust uses a warming grid to remove fog from the rear window.
Page 171: Rear Climate Control System
Rear Climate Control System (Off): Turn the knob, located on the left side of the control panel, to this position to turn the rear climate With this system the front or rear passengers can control system off. control the air temperature, air ﬂow and fan speed for the rear seat passengers.
Page 172 Rear Passenger Console Control (Mode): Press this button to select the air delivery mode and AUTO mode. Choose AUTO if you want To use the rear climate control from the rear passenger the system to automatically regulate the airﬂow. position, use the rear passenger console control. The See “Auto Mode”...
Page 173: Warning Lights, Gages, And Indicators
Warning Lights, Gages, and Gages can indicate when there may be or is a problem with one of your vehicle’s functions. Often gages Indicators and warning lights work together to let you know when there’s a problem with your vehicle. This part describes the warning lights and gages on When one of the warning lights comes on and stays on your vehicle.
Page 174: Instrument Panel Cluster
Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, about how much fuel you have and many other things you’ll need to know to drive safely and economically.
Page 175: Speedometer And Odometer
Speedometer and Odometer Safety Belt Reminder Light Your speedometer lets you see your speed in both When the key is turned to RUN or START, a chime will miles per hour (mph) and kilometers per hour (km/h). be provided for several seconds to remind people to buckle their safety belts.
Page 176: Airbag Readiness Light
Airbag Readiness Light CAUTION: There is an airbag readiness light on the instrument panel, which shows the airbag symbol. The system checks the airbag’s electrical system for malfunctions. If the airbag readiness light stays on after you The light tells you if there is an electrical problem. start your vehicle, it means the airbag system The system check includes the airbag sensors, the may not be working properly.
Page 177: Passenger Airbag Status Indicator
Passenger Airbag Status Indicator status indicator will light either ON or OFF, or either the on or off symbol to let you know the status of the right front passenger’s frontal airbag. If your vehicle has the passenger sensing system your rearview mirror will have a passenger airbag If the word ON or the on symbol is lit on the passenger status indicator.
Page 178: Charging System Light
Charging System Light If the word OFF or the off symbol is lit on the airbag status indicator, it means that the passenger sensing system has turned off the right front passenger’s frontal The charging system light airbag. See Passenger Sensing System on page 1-80 will come on brieﬂy when for more on this, including important safety information.
Page 179: Voltmeter Gage
Voltmeter Gage You can only drive for a short time with the reading in either warning zone. If you must drive, turn off all unnecessary accessories. When your engine is not Readings in either warning zone indicate a possible running, but the ignition is problem in the electrical system.
Page 180 CAUTION: Your brake system may not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to an accident. If the light is still United States Canada on after you have pulled off the road and This light should come on brieﬂy when you turn the stopped carefully, have the vehicle towed for ignition key to RUN.
Page 181: Anti-Lock Brake System Warning Light
Anti-Lock Brake System Warning Low Tire Pressure Warning Light Light This light and a chime will come on along with the With the anti-lock brake CHECK TIRE PRESSURE system, this light will come message in the DIC on when you start your when one or more of your engine and may stay on for tires is signiﬁcantly...
Page 182: Traction Off Light
Traction Off Light Engine Coolant Temperature Gage If you have the ® StabiliTrak system, this light should come on brieﬂy when you turn the ignition to RUN. If the light doesn’t come on then, the system may require service; have it ﬁxed so it will be there to warn you if the system is turned off.
Page 183: Transmission Temperature Gage
Transmission Temperature Gage At approximately 265°F (130°C), the DIC will display a TRANSMISSION HOT message and the transmission will enter a transmission protection mode. When the transmission enters the protection mode, you may notice a change in the transmission shifting patterns. The transmission will return to normal shifting patterns when the transmission ﬂuid temperature falls below 260°F (127°C).
Page 184: Malfunction Indicator Lamp
Malfunction Indicator Lamp Notice: If you drive your vehicle with the transmission temperature gage above normal operating range, you can damage the transmission. Check Engine Light This could lead to costly repairs that would not be covered by your warranty. Do not drive your Your vehicle is equipped vehicle while the transmission temperature gage with a computer which...
Page 185: If The Light Is Flashing
• Notice: If you keep driving your vehicle with this Light On Steady — An emission control system light on, after awhile, your emission controls malfunction has been detected on your vehicle. may not work as well, your fuel economy may not Diagnosis and service may be required.
Page 186: If The Light Is On Steady
If the Light Is On Steady Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See You may be able to correct the emission system Gasoline Octane on page 5-5. Poor fuel quality will malfunction by considering the following: cause your engine not to run as efficiently as designed.
Page 187: Oil Pressure Gage
Emissions Inspection and Maintenance Oil Pressure Gage Programs Some state/provincial and local governments have or may begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Here are some things you need to know to help your vehicle pass an inspection: Your vehicle will not pass this inspection if the check...
Page 188: Security Light
Security Light A reading in the low pressure zone may be caused by a dangerously low oil level or some other problem causing low oil pressure. Check your oil as soon This light will come on as possible. See DIC Warnings and Messages on brieﬂy when you turn the page 3-53.
Page 189: Cruise Control Light
Cruise Control Light Tow/Haul Mode Light This light comes on This light is displayed whenever you set your when the tow/haul mode cruise control. has been activated. The light will go out when the cruise control is turned For more information, see “Tow/Haul Mode” under off.
Page 190: Fuel Gage
Fuel Gage Here are some situations you may experience with your fuel gage. None of these indicate a problem with the fuel gage. • At the gas station, the fuel pump shuts off before the gage reads full. • It takes a little more or less fuel to ﬁll up than the fuel gage indicated.
Page 191: Driver Information Center (Dic)
Driver Information Center (DIC) The Driver Information Center (DIC) display is located on the instrument panel cluster, below the speedometer. The DIC buttons, if equipped, are located on the steering wheel. The DIC can display information such as the trip odometer, fuel economy, customization features and warning/status messages.
Page 192: Dic Operation And Displays
DIC Operation and Displays Trip B: Press the trip information button until TRIP B appears on the display. This mode shows the current distance traveled since the last reset for TRIP B in either The Driver Information Center (DIC) comes on when the miles or kilometers.
Page 193 • Fuel Information Button LR TIRE shows the tire pressure for the left rear tire. (Fuel Information): Press the fuel information • RR TIRE shows the tire pressure for the button to scroll through the range, fuel used, average right rear tire. fuel economy and the engine oil life system.
Page 194 Average Fuel Economy: Press the fuel information In addition to the engine oil life system monitoring the button until AVG ECON appears on the display. oil life, additional maintenance is recommended in This mode shows how many miles per gallon (MPG) or the Maintenance Schedule in this manual.
Page 195: Dic Warnings And Messages
DIC Warnings and Messages BATTERY NOT CHARGING On some vehicles, if the battery is not charging during Warning messages are displayed on the Driver operation, this message will appear on the DIC. Information Center (DIC) to notify the driver that the Driving with this problem could drain your battery.
Page 196 This reminder will be repeated if the ignition is on, the Pressing any of the four DIC buttons, if equipped, will vehicle is in motion, the driver is buckled and the acknowledge the message and clear it from the DIC passenger is still unbuckled and the passenger airbag is display.
Page 197 CHECK OIL LEVEL CHECK WASHER FLUID If the oil level in the vehicle is low, this message will If the washer ﬂuid level is low, this message will appear appear on the DIC. Check the oil level and correct it as on the DIC.
Page 198 ENGINE COOLANT HOT FUEL LEVEL LOW If the cooling system temperature gets hot, this message If the fuel level is low, this message will appear on the will appear in the DIC. Stop the vehicle and let the DIC and you will hear a chime. Refuel as soon as engine idle in PARK (P) to allow the coolant to reach a possible.
Page 199 LEFT REAR DOOR AJAR OIL LIFE RESET If the driver’s side rear door is not fully closed and the This message will appear on the display for about vehicle is in a drive gear, this message will appear 10 seconds after resetting the change engine oil on the display and you will hear a chime.
Page 200 PASSENGER DOOR AJAR REDUCED ENGINE POWER If the passenger’s door is not fully closed and the This message is displayed and you will hear a chime vehicle is in a drive gear, this message will appear on when the cooling system temperature gets too hot and the display and you will hear a chime.
Page 201 SERVICE 4WD SERVICE BRAKE SYSTEM If you have all-wheel-drive and a problem occurs with If a problem occurs with the brake system, this message the all-wheel-drive system, this message will appear on will appear on the DIC. If this message appears, stop the DIC.
Page 202 SERVICE RIDE CONTROL SERVICE TIRE MONITOR If a problem occurs with the suspension system, this This message will be displayed if any of the tire monitor message will appear on the DIC. If this message sensors have malfunctioned, if the tire monitor sensors appears, stop and turn off the vehicle.
Page 203 STABILITY SYS DISABLED TIGHTEN FUEL CAP The STABILITY SYS DISABLED message will turn on If the vehicle’s fuel cap is not tightened properly this ® when you press the StabiliTrak button, or when message may appear along with the check engine light the stability control has been automatically disabled.
Page 204 TRACTION SYS LIMITED TRANSMISSION HOT If the brake traction control system activates constantly If the transmission ﬂuid temperature becomes high, or if the brakes have heated up due to high-speed this message will appear on the DIC display. braking, brake traction control will be disabled and the When the transmission enters the protection mode, TRACTION SYS LIMITED message will be displayed.
Page 205: Dic Vehicle Customization
DIC Vehicle Customization The following situations can cause the transmission to operate at higher temperatures: Your vehicle may have customization capabilities that • Towing a trailer allow you to program some features to one setting • Hot outside air temperatures based on your preference.
Page 206 LOCK DOORS: WITH SPEED: The doors will lock Choose one of the available options and press the when the vehicle speed is above 8 mph (13 km/h) for customization button while it is displayed on the DIC to three seconds. select it and move on to the next feature.
Page 207 DOOR LOCK DELAY: ON: The doors will not lock until LOCK FEEDBACK: LAMPS: The parking lamps will ﬁve seconds after the last door or the liftgate is ﬂash each time you press the button with the lock closed. You will hear three chimes to signal that the symbol on the remote keyless entry transmitter.
Page 208 • UNLOCK FEEDBACK: HORN: The horn will chirp the HEADLAMP DELAY: 2 MIN second time you press the button with the unlock • HEADLAMP DELAY: 3 MIN symbol on the remote keyless entry transmitter. • HEADLAMP DELAY: OFF UNLOCK FEEDBACK: BOTH: The parking lamps will The amount of time you choose will be the amount of ﬂash each time you press the button with the unlock time that the headlamps stay on after you turn off...
Page 209 Curb View PERIMETER LIGHTS: OFF: The perimeter lights will not come on when you unlock the vehicle with the Press the customization button until CURB VIEW remote keyless entry transmitter. appears in the display. To select your preference for Choose one of the available options and press the curb view, press the select button while CURB VIEW is customization button while it is displayed on the DIC to displayed on the DIC.
Page 210 Alarm Warning Language Press the customization button until ALARM WARNING To select your preference for display language, press appears in the display. To select your preference for the select button while LANGUAGE is displayed on the alarm warning, press the select button while ALARM DIC.
Page 211: Display Units
Display Units Audio System(s) Press the customization button until DISPLAY UNITS Notice: Before adding any sound equipment to appears in the display. To select English or metric, press your vehicle, like a tape player, CB radio, mobile the select button while DISPLAY UNITS is displayed telephone, or two-way radio, make sure that it can on the DIC.
Page 212: Setting The Time
Setting the Time Radio with Cassette and CD Press and hold the HR button until the correct hour appears on the display. Press and hold the MN button until the correct minute appears on the display. The time can be set with the ignition on or off. To synchronize the time with an FM station broadcasting Radio Data System (RDS) information, press and hold the hour and minute buttons at the same time until RDS...
Page 213 Playing the Radio This system relies upon receiving speciﬁc information from these stations and will only work when the information is available. In rare cases, a radio station PWR (Power): Press this knob to turn the system on may broadcast incorrect information that will cause and off.
Page 214 Finding a Station AUTO VOL (Automatic Volume): Your vehicle has the ® ® Bose AudioPilot noise compensation technology. ® When turned on, AudioPilot continuously adjusts the BAND: Press this button to switch between FM1, FM2, audio system to compensate for background noise, AM, or XM1 or XM2 (if equipped).
Page 215 To scan preset stations, press and hold either the To store an equalization setting to a preset station SCAN or the TYPE arrows for more than four seconds. perform the following: PSCN will appear on the display and you will hear a 1.
Page 216 Adjusting the Speakers (Balance/Fade) AUTO EQ (Automatic Equalization): Press this button to enhance the audio performance for different passengers in the vehicle. AUDIO: To adjust the balance between the right and the left speakers, push and release the AUDIO The setting last chosen will appear on the display when knob until BAL appears on the display.
Page 217 Finding a Program Type (PTY) Station SCAN: Scan the stations within a PTY by performing the following: (RDS and XM™) 1. Press the TYPE button to activate program type To select and ﬁnd a desired PTY perform the following: select mode. TYPE and the last selected PTY will appear on the display.
Page 218 Setting Preset PTYs (RDS Only) If the entire message is not displayed, parts of the message will appear every three seconds. To scroll These buttons have factory PTY presets. Up to 12 PTYs through the message, press and release the INFO (six FM1 and six FM2), can be programmed on the button.
Page 219 XM™ Radio Messages Radio Display Condition Action Required Message XL (Explicit Language XL on the radio display, These channels, or any others, can be blocked at a Channels) after the channel name, customer’s request, by calling 1-800-852-XMXM (9696). indicates content with explicit language.
Page 220 XM™ Radio Messages (cont’d) Radio Display Condition Action Required Message No Info Category Name not No category information is available at this time on this available channel. The system is working properly. No Info No Text/Informational No text or informational messages are available at this message available time on this channel.
Page 221: Playing A Cassette Tape
Playing a Cassette Tape 1 PREV (Previous): The tape must have at least three seconds of silence between each selection for The tape player is built to work best with tapes that are previous to work. Press this pushbutton to go to the up to 30 to 45 minutes long on each side.
Page 222 © ¨ 2 NEXT: The tape must have at least three seconds of SCAN : Press and hold either the SCAN or the silence between each selection for next to work. TYPE arrows for more than two seconds until SCAN Press this pushbutton to go to the next selection on the appears on the display and you hear a beep.
Page 223: Cassette Tape Messages
Cassette Tape Messages If any error occurs repeatedly or if an error cannot be corrected, contact your GM dealer. If the radio displays an error message, write it down and provide it to CHK TAPE (Check Tape): If this message appears on your GM dealer when reporting the problem.
Page 224 Playing a CD 1 PREV (Previous): Press this pushbutton to go to the beginning of the current track if more than eight seconds Insert a CD partway into the slot, label side up. The have played. TRACK and the track number will appear on player will pull it in and the CD should begin playing.
Page 225 6 RDM (Random): Press this pushbutton to hear the TAPE DISC: Press this button to play a cassette tape tracks in random, rather than sequential, order. RDM ON or CD when listening to the radio. The inactive tape will appear on the display. RDM T and the track or CD will remain safely inside the radio for future number will appear on the display when each track listening.
Page 226: Rear Seat Entertainment System
Rear Seat Entertainment System If any error occurs repeatedly or if an error cannot be corrected, contact your GM dealer. If the radio displays an error message, write it down and provide it to Your vehicle may have a DVD Rear Seat your GM dealer when reporting the problem.
Page 227 Headphones Battery Replacement To change the batteries, do the following: The RSE system includes two sets of wireless headphones. 1. Loosen the screw on the battery compartment door located on the left side of the headphone earpiece. Each set of headphones has an ON/OFF control. An indicator light will illuminate on the headphones when 2.
Page 228 Audio Output To use the auxiliary inputs on the RSE system, connect an external auxiliary device to the color-coded RCA Audio from the DVD player or auxiliary inputs may be jacks and turn both the auxiliary device and the heard through the following possible sources: RSE system power on.
Page 229 The RSE system is capable of outputting audio to the To use the video screen, push forward on the release wired headphone jacks on the Rear Seat Audio system latch and the screen will fold down. Adjust the screen’s (if equipped). The RSE system may be selected as position as desired.
Page 230 Standard audio CDs, CD-R, CD-RW, Video CD and Photo CD/CD-R media are fully supported by this DVD player. DVD-R and DVD-RW media is supported if formatted as DVD-Video. DVD+R and DVD+RW media may or may not be supported by the DVD player. The DVD player does not support DVD-RAM, DVD-ROM, and DVD Audio media.
Page 231 (Play/Pause): Press this button to start play of a (Menu Navigation Arrows): Use the DVD or CD. Press this button while a DVD or CD is arrow buttons to navigate through a menu. playing to pause it. Press this button again to continue (Enter): Press this button to select the choices the play of the DVD or CD.
Page 232: Remote Control
Stopping and Resume Playback Remote Control To stop playing a disc, press and release the stop To use the remote control, aim it at the transmitter button on the DVD player faceplate or the remote window below the video screen and press the desired control.
Page 233 Remote Control Buttons (Set-up Menu): Press this button to adjust the color, tint, brightness, contrast, display mode, and dynamic range compression. The dynamic range compression feature can be used to reduce loud audio and increase low audio produced by some DVDs. (Audio): Press this button to display a menu that will only appear when a DVD is playing.
Page 234 1 through 0 (Numeric Keypad): The numeric keypad (Camera Angle): Press this button to change provides the capability of direct chapter, title, and camera angles on DVDs that have this feature when a track number selection. DVD is playing. The format and content of this function will vary for each disc.
Page 235 Battery Replacement Problem Recommended Action Disc will not play. The system might be off. To change the batteries, do the following: The parental control 1. Remove the battery compartment door located on button might have been the bottom of the remote control. turned on.
Page 236 Problem Recommended Action Problem Recommended Action In auxiliary mode, the Check the auxiliary input After stopping the player, I If the stop button was picture moves or scrolls. connections at both push Play but sometimes pressed one time, the devices. the DVD starts where I DVD player will resume Change the Video...
Page 237 DVD Messages Problem Recommended Action Sometimes the wireless Check for obstructions, The following errors may be displayed on the video headphone audio cuts out low batteries, reception screen: or buzzes. range and interference from cellular telephone Disc Format Error: This message will be displayed if a towers or by using your disc is inserted upside down, if the disc is not readable, cellular telephone in the...
Page 238: Navigation/Radio System
DVD Distortion Navigation/Radio System There may be an experience with audio distortion in the Your vehicle may have a navigation radio system that wireless headphones when operating cellular phones, includes Radio Data System (RDS) with Program scanners, CB radios, Global Positioning Systems Type (PTY) selections that will seek out the kind of (GPS)*, two-way radios, mobile fax, or walkie talkies.
Page 239: Rear Seat Audio (Rsa)
Rear Seat Audio (RSA) This feature allows rear seat passengers to listen to any of the sources: radio, cassette tapes, CDs, or DVDs. However, the rear seat passengers can only control the sources that the front seat passengers are not listening to.
Page 240 SRC (Source): Press this button to select a source: PROG (Program): Press this button to go to the next radio, cassette tapes, CDs, or DVDs. preset radio station set on the pushbuttons on the main radio. This function is inactive if the front seat SEEK : When listening to FM1, FM2, or AM, passengers are listening to the radio.
Page 241: Cd Changer
CD Changer To load a CD, perform the following steps: 1. Press the LOAD button. Available positions will blink amber. 2. Select a position by pressing the numbered button with the amber blinking light. If a button is not pressed within ﬁve seconds, the changer will go to the lowest available position.
Page 242 CD Functions To eject a single CD, perform the following steps: 1. Press the eject button (upward pointing arrow). The All of the CD changer functions are performed by the buttons with loaded CDs will blink amber. radio, except for loading and ejecting. 2.
Page 243 CD Changer Errors 6 RDM (Random): Press and release this pushbutton to hear all of the tracks on all of the loaded CDs in random, rather than sequential, order. RDM ALL CHK CD (Check): If this message appears on the will appear on the display.
Page 244: Theft-Deterrent Feature
Theft-Deterrent Feature Audio Steering Wheel Controls ® THEFTLOCK is designed to discourage theft of your vehicle’s radio. The feature works automatically by learning a portion of the Vehicle Identiﬁcation Number (VIN). If the radio is moved to a different vehicle, it will not operate and LOCKED will appear on the display.
Page 245: Radio Reception
Radio Reception PROG (Program): Press this button to play a station you have programmed on the radio preset pushbuttons. The radio will only seek preset stations with a strong signal that are in the selected band. The range for most AM stations is greater than for FM, When a CD is playing in the CD changer, press this especially at night.
Page 246: Care Of Your Cassette Tape Player
Care of Your Cassette Tape Player When cleaning the cassette tape player with the recommended non-abrasive cleaning cassette, it is possible that the cassette may eject, because the cut A tape player that is not cleaned regularly can cause tape detection feature on the radio may recognize it as a reduced sound quality, ruined cassettes, or a damaged broken tape, in error.
Page 247: Care Of Your Cds And Dvds
Care of Your CDs and DVDs A non-scrubbing action, wet-type cleaner which uses a cassette with a fabric belt to clean the tape head can be used. This type of cleaning cassette will not Handle discs carefully. Store them in their original cases eject on its own.
Page 248: Diversity Antenna System
Diversity Antenna System XM™ Satellite Radio Antenna System Your AM-FM antennas are located in the rear side windows. Be sure that the inside surfaces of the rear The XM™ Satellite Radio antenna is located on the roof side windows are not scratched and that the lines on the of your vehicle.
Page 249 Section 4 Driving Your Vehicle Your Driving, the Road, and Your Vehicle ..4-2 City Driving ..........4-36 Defensive Driving ...........4-2 Freeway Driving ...........4-37 Drunken Driving ..........4-2 Before Leaving on a Long Trip .......4-38 Control of a Vehicle ........4-6 Highway Hypnosis ........4-39 Braking ............4-6 Hill and Mountain Roads ........4-39 Anti-Lock Brake System (ABS) ......4-7...
Page 250: Your Driving, The Road, And Your Vehicle
Your Driving, the Road, and Defensive driving requires that a driver concentrate on the driving task. Anything that distracts from the Your Vehicle driving task — such as concentrating on a cellular telephone call, reading, or reaching for something on the ﬂoor —...
Page 251 Police records show that almost half of all motor The Blood Alcohol Concentration (BAC) of someone vehicle-related deaths involve alcohol. In most cases, who is drinking depends upon four things: these deaths are the result of someone who was • The amount of alcohol consumed drinking and driving.
Page 252 According to the American Medical Association, a 180 lb It is the amount of alcohol that counts. For example, if (82 kg) person who drinks three 12 ounce (355 ml) the same person drank three double martinis (3 ounces bottles of beer in an hour will end up with a BAC or 90 ml of liquor each) within an hour, the person’s of about 0.06 percent.
Page 253 The BAC will be over 0.10 percent after three to There is something else about drinking and driving that six drinks (in one hour). Of course, as we have seen, many people do not know. Medical research shows that it depends on how much alcohol is in the drinks, alcohol in a person’s system can make crash injuries and how quickly the person drinks them.
Page 254: Control Of A Vehicle
Control of a Vehicle 66 feet (20 m). That could be a lot of distance in an emergency, so keeping enough space between your vehicle and others is important. You have three systems that make your vehicle go where you want it to go. They are the brakes, the steering, and And, of course, actual stopping distances vary greatly the accelerator.
Page 255: Anti-Lock Brake System (Abs)
Anti-Lock Brake System (ABS) Your vehicle has anti-lock brakes. ABS is an advanced electronic braking system that will help prevent a braking skid. When you start your engine and begin to drive away, your anti-lock brake system will check itself. You may hear a momentary motor or clicking noise while this test is going on.
Page 256: Braking In Emergencies
The anti-lock system can change the brake pressure Remember: Anti-lock does not change the time you faster than any driver could. The computer is need to get your foot up to the brake pedal or always programmed to make the most of available tire and road decrease stopping distance.
Page 257: Road Sensing Suspension
® Road Sensing Suspension StabiliTrak System ® The Road Sensing Suspension (RSS) feature provides Your vehicle is equipped with StabiliTrak , which superior vehicle ride and handling under a variety of combines antilock brake, traction and stability control passenger and loading conditions. systems and helps the driver maintain directional control of the vehicle in most driving conditions.
Page 258 ® The STABILITY SYS ACTIVE message will appear on StabiliTrak and part of the Driver Information Center (DIC) only when the the traction control system system is both on and activated. It means that an can be turned off or advanced computer-controlled system has come on to back on by pressing the ®...
Page 259: Traction Control Operation
® When the StabiliTrak system has been turned off you The traction control system is enabled automatically may still hear system noises as a result of the when you start your vehicle, and it will activate brake-traction control coming on. and display the TRACTION ACTIVE message in the Driver Information Center (DIC) if it senses that any of To limit wheel spin and realize the full beneﬁts of the...
Page 260 If the brake traction-control system activates constantly The traction control system may activate on dry or or if the brakes have heated up due to high-speed rough roads or under conditions such as heavy braking, brake traction-control will be disabled and the acceleration while turning or abrupt upshifts/downshifts TRACTION SYS LIMITED message will be displayed.
Page 261: Steering
Steering Suppose you are steering through a sharp curve. Then you suddenly accelerate. Both control systems — steering and acceleration — have to do their Power Steering work where the tires meet the road. Adding the sudden acceleration can demand too much of those places. You If you lose power steering assist because the engine ®...
Page 262: Steering In Emergencies
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and ﬁnd a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Page 263: Off-Road Recovery
Off-Road Recovery Passing You may ﬁnd that your right wheels have dropped off the The driver of a vehicle about to pass another on a edge of a road onto the shoulder while you are driving. two-lane highway waits for just the right moment, accelerates, moves around the vehicle ahead, then goes back into the right lane again.
Page 264 • • Do not get too close to the vehicle you want to Check your mirrors, glance over your shoulder and pass while you are awaiting an opportunity. For one start your left lane change signal before moving out thing, following too closely reduces your area of of the right lane to pass.
Page 265: Loss Of Control
Loss of Control Remember: Any traction control system helps avoid only the acceleration skid. If your traction control system is off, then an acceleration skid is also best handled Let us review what driving experts say about what by easing your foot off the accelerator pedal. happens when the three control systems —...
Page 266: Operating Your All-Wheel-Drive Vehicle Off Paved Roads
Operating Your All-Wheel-Drive “Off-roading” means you have left the North American road system behind. Traffic lanes are not marked. Vehicle Off Paved Roads Curves are not banked. There are no road signs. Surfaces can be slippery, rough, uphill or downhill. In This off-road guide is for vehicles that have all-wheel short, you have gone right back to nature.
Page 267 Loading Your Vehicle for Off-Road Driving CAUTION: There are some important things to remember about how to load your vehicle. • Cargo on the load ﬂoor piled higher than the seatbacks can be thrown forward • The heaviest things should be on the load ﬂoor and during a sudden stop.
Page 268: Environmental Concerns
Environmental Concerns Traveling to Remote Areas Off-road driving can provide wholesome and satisfying It makes sense to plan your trip, especially when going recreation. However, it also raises environmental to a remote area. Know the terrain and plan your concerns. We recognize these concerns and urge every route.
Page 269 Scanning the Terrain Controlling your vehicle is the key to successful off-road driving. One of the best ways to control your vehicle Off-road driving can take you over many different kinds is to control your speed. Here are some things to keep of terrain.
Page 270 Driving on Off-Road Hills When you drive over obstacles or rough terrain, keep a ﬁrm grip on the steering wheel. Ruts, troughs or Off-road driving often takes you up, down or across a other surface features can jerk the wheel out of your hill.
Page 271 Approaching a Hill • Is there a straight path up or down the hill so you will not have to make turning maneuvers? When you approach a hill, you need to decide if it is • Are there obstructions on the hill that can block your one of those hills that is just too steep to climb, descend path, such as boulders, trees, logs, or ruts? or cross.
Page 272 Driving Uphill • Ease up on your speed as you approach the top of the hill. Once you decide you can safely drive up the hill, you • Attach a ﬂag to the vehicle to make you more need to take some special steps. visible to approaching traffic on trails or hills.
Page 273 Here are some things you must not do if you stall, or What should I do if my vehicle stalls, or is are about to stall, when going up a hill. about to stall, and I cannot make it up •...
Page 274 Driving Downhill CAUTION: When off-roading takes you downhill, you will want to consider a number of things: • How steep is the downhill? Will I be able to maintain Heavy braking when going down a hill can vehicle control? cause your brakes to overheat and fade. This could cause loss of control and a serious •...
Page 275 distance from the front wheels to the rear Am I likely to stall when going downhill? wheels — reduces the likelihood the vehicle will tumble end over end. But when you drive across an It is much more likely to happen going uphill. But if incline, the much more narrow track width —...
Page 276 Stalling on an Incline For reasons like these, you need to decide carefully whether to try to drive across an incline. Just because the If your vehicle stalls when you are crossing an incline, trail goes across the incline does not mean you have to be sure you, and any passengers, get out on the drive it.
Page 277 sink into the sand. This has an effect on steering, accelerating and braking. Drive at a reduced speed and CAUTION: avoid sharp turns or abrupt maneuvers. Hard packed snow and ice offer the worst tire traction. Getting out on the downhill (low) side of a On these surfaces, it is very easy to lose control.
Page 278 Driving in Water CAUTION: Heavy rain can mean ﬂash ﬂooding, and ﬂood waters demand extreme caution. Find out how deep the water is before you drive through Driving through rushing water can be it. If it is deep enough to cover your wheel hubs, dangerous.
Page 279: Driving At Night
After Off-Road Driving Driving at Night Remove any brush or debris that has collected on the underbody, chassis or under the hood. These accumulations can be a ﬁre hazard. After operation in mud or sand, have the brake linings cleaned and checked. These substances can cause glazing and uneven braking.
Page 280 Here are some tips on night driving. You can be temporarily blinded by approaching headlamps. It can take a second or two, or even several • Drive defensively. seconds, for your eyes to re-adjust to the dark. When • Do not drink and drive. you are faced with severe glare, as from a driver who does not lower the high beams, or a vehicle with •...
Page 281: Driving In Rain And On Wet Roads
Driving in Rain and on Wet Roads Rain and wet roads can mean driving trouble. On a wet road, you cannot stop, accelerate, or turn as well because your tire-to-road traction is not as good as on dry roads. And, if your tires do not have much tread left, you will get even less traction.
Page 282: Driving Through Deep Standing Water
Hydroplaning Driving too fast through large water puddles or even going through some car washes can cause problems, Hydroplaning is dangerous. So much water can build up too. The water may affect your brakes. Try to avoid under your tires that they can actually ride on the puddles.
Page 283: Driving Through Flowing Water
Driving Through Flowing Water Some Other Rainy Weather Tips • Turn on your low-beam headlamps — not just your parking lamps — to help make you more visible CAUTION: to others. • Besides slowing down, allow some extra following Flowing or rushing water creates strong distance.
Page 284: City Driving
City Driving Here are ways to increase your safety in city driving: • Know the best way to get to where you are going. Get a city map and plan your trip into an unknown part of the city just as you would for a cross-country trip.
Page 285: Freeway Driving
Freeway Driving The most important advice on freeway driving is: Keep up with traffic and keep to the right. Drive at the same speed most of the other drivers are driving. Too-fast or too-slow driving breaks a smooth traffic ﬂow. Treat the left lane on a freeway as a passing lane.
Page 286: Before Leaving On A Long Trip
Once you are moving on the freeway, make certain you Is your vehicle ready for a long trip? If you keep it allow a reasonable following distance. Expect to serviced and maintained, it is ready to go. If it needs move slightly slower at night.
Page 287: Highway Hypnosis
Highway Hypnosis Hill and Mountain Roads Is there actually such a condition as highway hypnosis? Or is it just plain falling asleep at the wheel? Call it highway hypnosis, lack of awareness, or whatever. There is something about an easy stretch of road with the same scenery, along with the hum of the tires on the road, the drone of the engine, and the rush of the wind against the vehicle that can make you sleepy.
Page 288 • Keep your vehicle in good shape. Check all ﬂuid levels and also the brakes, tires, cooling system, CAUTION: and transmission. These parts can work hard on mountain roads. Coasting downhill in NEUTRAL (N) or with the • Know how to go down hills. The most important ignition off is dangerous.
Page 289: Winter Driving
Winter Driving Here are some tips for winter driving: • Have your vehicle in good shape for winter. • You may want to put winter emergency supplies in your vehicle. Also see Tires on page 5-60. Include an ice scraper, a small brush or broom, a supply of windshield washer ﬂuid, a rag, some winter outer clothing, a small shovel, a ﬂashlight, a red cloth, and a couple of reﬂective warning triangles.
Page 290: Driving On Snow Or Ice
Driving on Snow or Ice What is the worst time for this? Wet ice. Very cold snow or ice can be slick and hard to drive on. But wet ice Most of the time, those places where your tires meet can be even more trouble because it may offer the least the road probably have good traction.
Page 291: If You Are Caught In A Blizzard
• If You Are Caught in a Blizzard Allow greater following distance on any slippery road. If you are stopped by heavy snow, you could be in a • Watch for slippery spots. The road might be ﬁne serious situation. You should probably stay with until you hit a spot that is covered with ice.
Page 292 CAUTION: Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You cannot see it or smell it, so you might not know it is in your vehicle.
Page 293: If You Are Stuck: In Sand, Mud, Ice Or Snow
Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine CAUTION: again and repeat this only when you feel really uncomfortable from the cold. But do it as little as possible.
Page 294: Rocking Your Vehicle To Get It Out
Rocking Your Vehicle to Get It Out First, turn your steering wheel left and right. That will clear the area around your front wheels. If your vehicle has the ® StabiliTrak System, turn the system off by pressing the ® StabiliTrak button so that the STABILITY SYS DISABLED message and the traction off light are...
Page 295: Loading Your Vehicle
Tire and Loading Information Label Notice: Never use recovery hooks to tow the vehicle. Your vehicle could be damaged and it would not be covered by warranty. Loading Your Vehicle It is very important to know how much weight your vehicle can carry.
Page 296 The Tire and Loading Information label also shows the 4. The resulting ﬁgure equals the available amount of size of the original equipment tires (C) and the cargo and luggage load capacity. For example, if recommended cold tire inﬂation pressures (D). For more the “XXX”...
Page 297 Example 1 Example 2 Item Description Total Item Description Total Vehicle Capacity Weight Vehicle Capacity Weight 1,000 lbs (453 kg) 1,000 lbs (453 kg) for Example 1 for Example 2 Subtract Occupant Subtract Occupant Weight 150 lbs 300 lbs (136 kg) Weight 150 lbs 750 lbs (136 kg) (68 kg)
Page 298 Item Description Total Vehicle Capacity Weight 1,000 lbs (453 kg) for Example 3 Subtract Occupant Weight 200 lbs 1,000 lbs (453 kg) (91 kg) Available Cargo 0 lbs (0 kg) Weight Refer to your vehicle’s tire and loading information label for speciﬁc information about your vehicle’s capacity weight and seating positions.
Page 299 Certiﬁcation/Tire Label weigh station and weigh your vehicle. Your dealer can help you with this. Be sure to spread out your load equally on both sides of the centerline. Never exceed the GVWR for your vehicle, or the GAWR for either the front or rear axle. And, if you do have a heavy load, you should spread it out.
Page 300 Using heavier suspension components to get added There’s also important loading information for off-road durability might not change your weight ratings. Ask your driving in this manual. See “Loading Your Vehicle dealer to help you load your vehicle the right way. for Off-Road Driving”...
Page 301: Towing
Automatic Level Control Towing The automatic level control rear suspension comes as a part of the Road Sensing Suspension. See Road Towing Your Vehicle Sensing Suspension on page 4-9. Consult your dealer or a professional towing service if This type of level control is fully automatic and will you need to have your disabled vehicle towed.
Page 302: Trailer Recommendations
Dinghy Towing and Dolly Towing You’ll get the best performance if you spread out the weight of your load the right way, and if you choose the All-Wheel Drive Vehicles correct hitch and trailer brakes. Your vehicle is not designed to be towed with any of the For more information, see Towing a Trailer on wheels on the ground.
Page 303: If You Do Decide To Pull A Trailer
• Notice: Pulling a trailer improperly can damage Consider using a sway control. See “Hitches” later your vehicle and result in costly repairs not covered in this section. by your warranty. To pull a trailer correctly, follow • Don’t tow a trailer at all during the ﬁrst 500 miles the advice in this part, and see your dealer for (800 km) your new vehicle is driven.
Page 304 Tow/Haul Mode Tow/haul is designed to assist while your vehicle is pulling a large or heavy load or trailer. Tow/haul is most useful while pulling such a load in rolling terrain, in stop-and-go traffic, or when you need improved low-speed control, such as when parking. The purpose of the tow/haul mode is to do the following: •...
Page 305 A light on the instrument Operating the vehicle in tow/haul when lightly loaded or panel will illuminate to with no trailer at all will not cause damage. However, indicate that tow/haul there is no beneﬁt to the selection of tow/haul when the mode has been selected.
Page 306: Weight Of The Trailer
Weight of the Trailer Use one of the following charts to determine how much your vehicle can weigh, based upon your vehicle How heavy can a trailer safely be? model and options. It depends on how you plan to use your rig. For Maximum trailer weight is calculated assuming only the example, speed, altitude, road grades, outside driver is in the tow vehicle and it has all the required...
Page 307: Weight Of The Trailer Tongue
Weight of the Trailer Tongue The trailer tongue weight (A) should be 10 percent to 15 percent of the total loaded trailer weight (B), up to a The tongue load (A) of any trailer is an important weight maximum of 600 lbs (272 kg) with a weight carrying to measure because it affects the total or gross weight hitch.
Page 308 Total Weight on Your Vehicle’s Tires Weight-Distributing Hitches and Weight Carrying Hitches Be sure your vehicle’s tires are inﬂated to the upper limit for cold tires. You’ll ﬁnd these numbers on the Certiﬁcation label at the rear edge of the driver’s door or see Loading Your Vehicle on page 4-47.
Page 309: Trailer Brakes
Trailer Brakes When using a weight-distributing hitch, the hitch must be adjusted so that the distance (A) remains the If your trailer weighs more than 2,000 lbs (900 kg) same both before and after coupling the trailer to the loaded, then it needs its own brakes — and they must tow vehicle.
Page 310: Driving With A Trailer
Driving with a Trailer Towing a trailer requires a certain amount of experience. Before setting out for the open road, you’ll want to get to know your rig. Acquaint yourself with the feel of handling and braking with the added weight of the trailer. CAUTION: And always keep in mind that the vehicle you are driving is now a good deal longer and not nearly as...
Page 311: Following Distance
Following Distance Making Turns Stay at least twice as far behind the vehicle ahead as Notice: Making very sharp turns while trailering you would when driving your vehicle without a trailer. could cause the trailer to come in contact with the This can help you avoid situations that require vehicle.
Page 312: Driving On Grades
Driving On Grades Parking on Hills Reduce speed and shift to a lower gear before you start down a long or steep downgrade. If you don’t shift CAUTION: down, you might have to use your brakes so much that they would get hot and no longer work well. You really should not park your vehicle, with a You can tow in DRIVE (D).
Page 313 When You Are Ready to Leave After Trailer Wiring Harness Parking on a Hill Heavy-Duty Trailer Wiring Package 1. Apply your regular brakes and hold the pedal down while you: • start your engine, • shift into a gear, and •...
Page 314 Electric Brake Control Jumper The seven-wire harness contains the following trailer circuits: • Yellow: Left Stop/Turn Signal • Dark Green: Right Stop/Turn Signal • Brown: Taillamps • White: Ground • Light Green: Back-up Lamps • Red: Battery Feed • Dark Blue: Trailer Brake This harness may be included with your vehicle as part of the heavy-duty trailer wiring package.
Page 315 Four-Wire Harness Adapter This adapter may be included with your vehicle as part of the heavy-duty trailer wiring package. Use this adapter to connect a standard four-way round pin connector to the seven-wire harness Connect the adapter with the tab pointing up. The ﬂip cap on the vehicle’s seven-wire harness will lock on your vehicle.
Page 316 NOTES 4-68...
Page 317 Section 5 Service and Appearance Care Service ............5-3 Power Steering Fluid ........5-34 Doing Your Own Service Work ......5-4 Windshield Washer Fluid ........5-35 Adding Equipment to the Outside Brakes ............5-36 of Your Vehicle ...........5-4 Battery ............5-40 Jump Starting ..........5-41 Fuel ..............5-5 Gasoline Octane ..........5-5 All-Wheel Drive ..........5-45 Gasoline Speciﬁcations ........5-5...
Page 318 Section 5 Service and Appearance Care Inﬂation - Tire Pressure .........5-67 Care of Safety Belts ........5-102 Tire Pressure Monitor System ......5-68 Weatherstrips ..........5-102 Tire Inspection and Rotation ......5-71 Washing Your Vehicle ........5-103 When It Is Time for New Tires .......5-73 Cleaning Exterior Lamps/Lenses ....5-103 Buying New Tires .........5-74 Finish Care ..........5-103...
Page 319: Service
Service California Proposition 65 Warning Most motor vehicles, including this one, contain and/or Your dealer knows your vehicle best and wants you to emit chemicals known to the State of California to be happy with it. We hope you will go to your dealer cause cancer and birth defects or other reproductive for all your service needs.
Page 320: Doing Your Own Service Work
Doing Your Own Service Work CAUTION: If you want to do some of your own service work, you will want to use the proper service manual. It tells you much more about how to service your vehicle than You can be injured and your vehicle could be this manual can.
Page 321: Fuel
Fuel If your vehicle has the 6.0L HO engine (VIN Code N), use premium unleaded gasoline with a posted octane of 91 or higher for best performance. You may also use The 8th digit of your vehicle identiﬁcation number (VIN) middle grade or regular unleaded gasoline rated at shows the code letter or number that identiﬁes your 87 octane or higher, but your vehicle’s acceleration may...
Page 322: California Fuel
California Fuel Additives If your vehicle is certiﬁed to meet California Emission To provide cleaner air, all gasolines in the United States Standards (see the underhood emission control label), it are now required to contain additives that will help is designed to operate on fuels that meet California prevent engine and fuel system deposits from forming, speciﬁcations.
Page 323: Fuels In Foreign Countries
Fuels in Foreign Countries Gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines may be available in your area to contribute to clean air. General Motors If you plan on driving in another country outside the recommends that you use these gasolines, particularly if United States or Canada, the proper fuel may be hard they comply with the speciﬁcations described earlier.
Page 324: Filling Your Tank
Filling Your Tank To remove the fuel cap, turn it slowly to the left (counterclockwise). It will require more effort to turn the fuel cap on the last turn as you loosen it. CAUTION: CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries.
Page 325 Be careful not to spill fuel. Do not top off or overﬁll the tank and wait a few seconds after you have ﬁnished CAUTION: pumping before removing the nozzle. Clean fuel from painted surfaces as soon as possible. See Washing Your Vehicle on page 5-103. If a ﬁre starts while you are refueling, do not remove the nozzle.
Page 326: Filling A Portable Fuel Container
Filling a Portable Fuel Container Checking Things Under the Hood CAUTION: CAUTION: Never ﬁll a portable fuel container while it is in your vehicle. Static electricity discharge from An electric fan under the hood can start up the container can ignite the gasoline vapor. and injure you even when the engine is not You can be badly burned and your vehicle running.
Page 327: Hood Release
Hood Release To open the hood do the following: 1. Pull the handle located inside the vehicle to the lower left of the steering wheel. 2. Then go to the front of the vehicle and pull up on the secondary hood release located near the center of the grille.
Page 328: Engine Compartment Overview
Engine Compartment Overview When you open the hood on the VORTEC™ 6000 High-Output V8 engine, here is what you will see: 5-12...
Page 329: Engine Oil
A. Engine Air Cleaner/Filter. See Engine Air K. Brake Fluid Reservoir. See “Brake Fluid” under Cleaner/Filter on page 5-18. Brakes on page 5-36. B. Coolant Surge Tank and Pressure Cap. See Cooling L. Underhood Fuse Block. See Underhood Fuse Block System on page 5-29 and Coolant Surge Tank on page 5-113.
Page 330: What Kind Of Engine Oil To Use
The engine oil dipstick handle is a yellow loop. See See Engine Compartment Engine Compartment Overview on page 5-12 for Overview on page 5-12 for the location of the engine oil dipstick. the location of the engine oil ﬁll cap. 1.
Page 331 • SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50. Oils meeting these requirements should also have the starburst symbol on the container.
Page 332: Engine Oil Life System
Engine Oil Life System You should look for this information on the oil container, and use only those oils that are identiﬁed as meeting GM Standard GM6094M and have the starburst symbol When to Change Engine Oil on the front of the oil container. Your vehicle has a computer system that lets you know Notice: Use only engine oil identiﬁed as meeting when to change the engine oil and ﬁlter.
Page 333: What To Do With Used Oil
How to Reset the Engine Oil Life What to Do with Used Oil System Used engine oil contains certain elements that may be unhealthy for your skin and could even cause cancer. The Engine Oil Life System calculates when to change Do not let used oil stay on your skin for very long.
Page 334: Engine Air Cleaner/Filter
Engine Air Cleaner/Filter On vehicles without an air ﬁlter restriction indicator, inspect the air cleaner/ﬁlter at the Maintenance II intervals and replace it at the ﬁrst oil change after See Engine Compartment 50,000 miles (83 000 km). See Scheduled Maintenance Overview on page 5-12 for on page 6-4 for more information.
Page 335 Replacing the Engine Air Cleaner/Filter and Resetting the Air Filter Restriction Indicator 3. Remove the engine air cleaner/ﬁlter from the housing. Care should be taken to dislodge as little dirt as possible. 4. Clean the engine air cleaner/ﬁlter sealing surfaces 1.
Page 336: Automatic Transmission Fluid
Automatic Transmission Fluid 6. Reinstall the cover and tighten the screws. 7. Reset the air ﬁlter restriction indicator, if equipped, When to Check and Change by pressing the top button on the indicator. A good time to check your automatic transmission ﬂuid level is when the engine oil is changed.
Page 337: How To Check
How to Check Get the vehicle warmed up by driving about 15 miles (24 km) when outside temperatures are above Because this operation can be a little difficult, you may 50°F (10°C). If it is colder than 50°F (10°C), drive choose to have this done at the dealership service the vehicle in THIRD (3) until the engine temperature department.
Page 338 Then, without shutting off the engine, follow these steps: The transmission dipstick handle with this graphic is located at the rear of the engine compartment, on the passenger’s side of the vehicle. See Engine Compartment Overview on page 5-12 for 3.
Page 339: Engine Coolant
How to Add Fluid Engine Coolant Refer to the Maintenance Schedule to determine what The cooling system in your vehicle is ﬁlled with kind of transmission ﬂuid to use. See Recommended ® DEX-COOL engine coolant. This coolant is designed Fluids and Lubricants on page 6-13. to remain in your vehicle for ﬁve years or 150,000 miles (240 000 km), whichever occurs ﬁrst, if you add only Add ﬂuid only after checking the transmission ﬂuid while...
Page 340 What to Use Notice: If you use an improper coolant mixture, your engine could overheat and be badly damaged. Use a mixture of one-half clean, drinkable water and The repair cost would not be covered by your ® one-half DEX-COOL coolant which will not damage warranty.
Page 341 Checking Coolant Adding Coolant ® If you need more coolant, add the proper DEX-COOL The coolant surge tank is located in the engine coolant mixture at the surge tank, but only when the compartment on the passenger’s side of the vehicle. engine is cool.
Page 342: Coolant Surge Tank Pressure Cap
Coolant Surge Tank Pressure Cap Engine Overheating You will ﬁnd a coolant temperature gage on your vehicle’s instrument panel cluster. See Engine Coolant Temperature Gage on page 3-40. In addition, you will ﬁnd an ENGINE COOLANT HOT, ENGINE OVERHEATED and a REDUCED ENGINE POWER message in the Driver Information Center (DIC) on the instrument panel.
Page 343: If Steam Is Coming From Your Engine
If Steam Is Coming From Your Engine Notice: If your engine catches ﬁre because you keep driving with no coolant, your vehicle can be badly damaged. The costly repairs would not be covered by your warranty. See Overheated Engine CAUTION: Protection Operating Mode on page 5-28 for information on driving to a safe place in an emergency.
Page 344: Overheated Engine Protection Operating Mode
If you get the overheat warning with no sign of steam, If you still have the warning, turn off the engine and get try this for a minute or so: everyone out of the vehicle until it cools down. Also, see “Overheated Engine Protection Operating Mode”...
Page 345: Cooling System
Cooling System CAUTION: When you decide it is safe to lift the hood, here is what you will see: An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan.
Page 346 The coolant level should If there seems to be no leak and your vehicle is be at or above the FULL equipped with an electric engine cooling fan, with the COLD mark. If it is not, you engine on check to see if the cooling fan is running. If it may have a leak at the is not, your vehicle needs service.
Page 347: How To Add Coolant To The Coolant Surge Tank
How to Add Coolant to the Coolant Surge Tank CAUTION: If you have not found a problem yet, check to see if coolant is visible in the surge tank. If coolant is visible Adding only plain water to your cooling but the coolant level is not at or above the FULL COLD system can be dangerous.
Page 348 CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. 1. You can remove the coolant surge tank pressure cap when the cooling system, including the coolant surge tank pressure cap and upper radiator hose, is no longer hot.
Page 349 3. Fill the coolant surge tank with the proper mixture, 4. With the coolant surge tank pressure cap off, start to the FULL COLD mark. the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fan.
Page 350: Engine Fan Noise
Engine Fan Noise Power Steering Fluid If your vehicle is equipped with a clutched engine cooling fan, when the clutch is engaged, the fan spins faster to provide more air to cool the engine. In most everyday driving conditions, the fan is spinning slower and the clutch is not fully engaged.
Page 351: How To Check Power Steering Fluid
How to Check Power Steering Fluid What to Use To determine what kind of ﬂuid to use, see Locate the cap with this Recommended Fluids and Lubricants on page 6-13. symbol. See Engine Always use the proper ﬂuid. Failure to use the proper Compartment Overview on ﬂuid can cause leaks and damage hoses and seals.
Page 352: Brakes
Brakes Open the cap with the washer symbol on it. Add washer ﬂuid until the Brake Fluid tank is full. See Engine Compartment Overview on Your brake master cylinder page 5-12 for reservoir reservoir is ﬁlled with location. DOT-3 brake ﬂuid. See Engine Compartment Overview on page 5-12 for the location of the reservoir.
Page 353: Checking Brake Fluid
Checking Brake Fluid So, it is not a good idea to top off your brake ﬂuid. Adding brake ﬂuid will not correct a leak. If you add ﬂuid You can check the brake ﬂuid without taking off the cap. when your linings are worn, then you will have too much ﬂuid when you get new brake linings.
Page 354 What to Add Notice: • Using the wrong ﬂuid can badly damage brake When you do need brake ﬂuid, use only DOT-3 brake system parts. For example, just a few drops of ﬂuid. Use new brake ﬂuid from a sealed container mineral-based oil, such as engine oil, in your only.
Page 355: Brake Wear
Brake Wear Properly torqued wheel nuts are necessary to help prevent brake pulsation. When tires are rotated, inspect Your vehicle has four-wheel disc brakes. brake pads for wear and evenly tighten wheel nuts in the proper sequence to GM torque speciﬁcations. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads Brake linings should always be replaced as complete...
Page 356: Battery
Replacing Brake System Parts Warning: Battery posts, terminals and related accessories contain lead and lead compounds, The braking system on a vehicle is complex. Its many chemicals known to the State of California to cause parts have to be of top quality and work well together if cancer and reproductive harm.
Page 357: Jump Starting
Jump Starting Notice: If the other vehicle’s system is not a 12-volt system with a negative ground, both vehicles can be damaged. Only use vehicles with 12-volt systems If your battery has run down, you may want to use with negative grounds to jump start your vehicle. another vehicle and some jumper cables to start your vehicle.
Page 358 4. Open the hoods and locate the positive (+) and The remote negative ( ) negative ( ) terminal locations of the other vehicle. terminal is located on the engine accessory drive Your vehicle has a remote positive (+) jump bracket and is starting terminal and a remote negative ( ) jump marked GND.
Page 359 Before you connect the cables, here are some basic things you should know. Positive (+) will go to CAUTION: positive (+) or to a remote positive terminal (+) if the vehicle has one. Negative ( ) will go to a heavy, unpainted metal engine part or to a remote Using a match near a battery can cause battery negative ( ) terminal, if the vehicle has one.
Page 360 8. Now connect the black negative ( ) cable to the Notice: If the jumper cables are removed in the negative ( ) terminal of the good battery. Use a wrong order, electrical shorting may occur and remote negative ( ) terminal if the vehicle has one. damage the vehicle.
Page 361: All-Wheel Drive
How to Check Lubricant To disconnect the jumper cables from both vehicles do the following: 1. Disconnect the black negative ( ) cable from the vehicle that had the dead battery. 2. Disconnect the black negative ( ) cable from the vehicle with the good battery.
Page 362: Rear Axle
What to Use How to Check Lubricant Refer to the Maintenance Schedule to determine what kind of lubricant to use. See Recommended Fluids and Lubricants on page 6-13. Rear Axle When to Check Lubricant It is not necessary to regularly check rear axle ﬂuid unless you suspect there is a leak or you hear an unusual noise.
Page 363: Front Axle
Front Axle To get an accurate reading, the vehicle should be on a level surface. When to Check and Change Lubricant If the level is below the bottom of the ﬁller plug hole, located on the front axle, you may need to add It is not necessary to regularly check front axle ﬂuid some lubricant: unless you suspect there is a leak or you hear an...
Page 364: Headlamp Aiming
Headlamp Aiming Notice: To make sure your headlamps are aimed properly, read all the instructions before beginning. Failure to follow these instructions could cause damage to headlamp parts. The vehicle should be properly prepared as follows: • The vehicle should be placed so the headlamps are 25 ft.
Page 365: Headlamp Horizontal Aiming
Headlamp Horizontal Aiming The headlamp aiming devices are under the hood near the headlamps. Turn the horizontal aiming screw (A) until the indicator (B) is lined up with zero. Once the horizontal aim is adjusted, then adjust the If you believe your headlamps need horizontal (H) vertical aim.
Page 366: Headlamp Vertical Aiming
Headlamp Vertical Aiming 3. At the wall or other ﬂat surface, measure from the ground upward the recorded distance from Step 2 and draw or tape a horizontal line the width of Notice: Horizontal aiming must be performed the vehicle. before making any adjustments to the vertical aim.
Page 367: Bulb Replacement
Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 5-58. For any bulb changing procedure not listed in this section, contact your dealer. High Intensity Discharge (HID) Lighting CAUTION: 5. Turn the vertical aiming screw (V) until the The low beam high intensity discharge lighting headlamp beam is aimed to the horizontal tape line.
Page 368: Halogen Bulbs
Halogen Bulbs Headlamps CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package. A. Low-Beam D.
Page 369 To replace a headlamp bulb, do the following: 1. Open the hood of the vehicle. See Hood Release on page 5-11 for more information. 4. Pull the top left or right corner of the grill out so the clips release. This will give you the needed clearance for removing the headlamp assembly.
Page 370 5. Remove the horizontal pin from the headlamp 6. Remove the vertical pin from the headlamp assembly by lifting the end of the pin upward assembly by turning the end of the pin away from until it unsnaps and then pulling it toward the you until it unsnaps and then pulling it upward.
Page 371 9. Remove the rubber, circular-shaped bulb cap of the affected bulb from the headlamp assembly. 10. Turn the bulb connector counterclockwise and 13. Place the headlamp assembly back into the vehicle, remove it with the old bulb from the headlamp being sure to align the lower locator tab with the assembly.
Page 372: Front Turn Signal, Sidemarker And Daytime Running Lamps
Front Turn Signal, Sidemarker and To replace a front turn signal, sidemarker or DRL bulb, do the following: Daytime Running Lamps 1. Remove the headlamp assembly as described previously. See Headlamps on page 5-52 for more information. 2. Remove the rubber, circular-shaped bulb cap for the affected bulb from the headlamp assembly.
Page 373: Taillamps
Taillamps To replace a taillamp bulb, do the following: 1. Remove the two A. Turn Signal/Taillamp screws from the B. Stoplamp/Taillamp lamp assembly. C. Back-up Lamp D. Sidemarker Lamp 2. Remove the lamp assembly. 3. Press the release tab and turn the bulb socket counterclockwise to remove it from the taillamp housing.
Page 374: Replacement Bulbs
Replacement Bulbs 4. Pull the bulb straight out from the socket. Exterior Lamp Bulb Number Back-up Lamp 3157K Daytime Running Lamp (DRL) 4114K Front Marker Lamp Front Parking and Turn 3157AK Signal Lamps High-Beam Headlamp 9005 or 9005 LL Rear Turn Signal, Stoplamp 3157K and Taillamp Sidemarker Lamp...
Page 375: Windshield Wiper Blade Replacement
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected at least twice a year for wear and cracking. See Scheduled Maintenance on page 6-4 for more information. Replacement blades come in different types and are removed in different ways. For proper type and length, see Normal Maintenance Replacement Parts on page 6-15.
Page 376: Tires
Tires CAUTION: (Continued) Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions • Underinﬂated tires pose the same danger about your tire warranty and where to obtain service, as overloaded tires. The resulting accident see your GM Warranty booklet for details.
Page 377: Tire Sidewall Labelling
Tire Sidewall Labelling (B) TPC Spec (Tire Performance Criteria Speciﬁcation): Original equipment tires designed to GM’s speciﬁc tire performance criteria have a TPC Useful information about a tire is molded into the speciﬁcation code molded onto the sidewall. GM’s TPC sidewall.
Page 378 (B) TPC Spec (Tire Performance Criteria Speciﬁcation): Original equipment tires designed to GM’s speciﬁc tire performance criteria have a TPC speciﬁcation code molded onto the sidewall. GM’s TPC speciﬁcations meet or exceed all federal safety guidelines. (C) Dual Tire Maximum Load: Maximum load that can be carried and the maximum pressure needed to support that load when used in a dual conﬁguration.
Page 379: Tire Size
Tire Size (E) Tire Identiﬁcation Number (TIN): The letters and numbers following DOT code are the Tire Identiﬁcation The following examples show the different parts of Number (TIN). The TIN shows the manufacturer and a tire size. plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture.
Page 380: Tire Terminology And Deﬁnitions
Tire Terminology and Deﬁnitions (A) Light Truck (LT-Metric) Tire: The United States version of a metric tire sizing system. The letters LT as the ﬁrst two characters in the tire size means a light Air Pressure: The amount of air inside the tire pressing truck tire engineered to standards set by the U.S.
Page 381 Curb Weight: This means the weight of a motor Load Index: An assigned number ranging from 1 to vehicle with standard and optional equipment including 279 that corresponds to the load carrying capacity the maximum capacity of fuel, oil and coolant, but of a tire.
Page 382 Passenger (P-Metric) Tire: A tire used on passenger Treadwear Indicators: Narrow bands, sometimes cars and some light duty trucks and multipurpose called “wear bars,” that show across the tread of a tire vehicles. when only 1/16 inch (1.6 mm) of tread remains. See When It Is Time for New Tires on page 5-73.
Page 383: Inﬂation - Tire Pressure
Inﬂation - Tire Pressure A Tire and Loading Information label is attached to the vehicle’s center pillar (B-pillar), below the driver’s door lock post (striker). This label lists your vehicle’s Tires need the correct amount of air pressure to operate original equipment tires and their recommended cold tire effectively.
Page 384: Tire Pressure Monitor System
Remove the valve cap from the tire valve stem. Press When a low tire pressure condition is detected, the TPM the tire gage ﬁrmly onto the valve to get a pressure system will display the CHECK TIRE PRESSURE measurement. If the cold tire inﬂation pressure matches warning message on the Driver Information Center (DIC);...
Page 385 The Tire and Loading Information label (tire information You will have one minute to match the ﬁrst tire/wheel placard) shows the size of your vehicle’s original position, and ﬁve minutes overall to match all four tires and the correct inﬂation pressure for your vehicle’s tire/wheel positions.
Page 386 5. Remove the valve cap from the valve cap stem. 9. After hearing the conﬁrming horn chirp for the left Activate the TPM sensor by increasing or rear tire, check to see if the TPM warning light is decreasing the tire’s air pressure for 10 seconds, still ﬂashing.
Page 387: Tire Inspection And Rotation
Federal Communications Commission and Tire Inspection and Rotation Industry and Science Canada Tires should be rotated every 5,000 to 8,000 miles The TPM system operates on a radio frequency subject (8 000 to 13 000 km). to Federal Communications Commission (FCC) Rules Any time you notice unusual wear, rotate your tires as and with Industry and Science Canada.
Page 388 The purpose of regular rotation is to achieve more After the tires have been rotated, adjust the front and uniform wear for all tires on the vehicle. The ﬁrst rotation rear inﬂation pressures as shown on the tire and loading is the most important.
Page 389: When It Is Time For New Tires
When It Is Time for New Tires You need a new tire if any of the following statements are true: • You can see the indicators at three or more places One way to tell when it’s time for new tires is to around the tire.
Page 390: Buying New Tires
Buying New Tires CAUTION: To ﬁnd out what kind and size of tires you need, look at the Certiﬁcation/Tire label or the Tire and Loading Information label. See Loading Your Vehicle on Mixing tires could cause you to lose control page 4-47 for more information about these labels and while driving.
Page 391: Uniform Tire Quality Grading
The grades are molded on the sidewalls of most passenger car tires. The Uniform Tire Quality Grading CAUTION: system does not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches If you use bias-ply tires on your vehicle, the (25 to 30 cm), or to some limited-production tires.
Page 392: Wheel Alignment And Tire Balance
Traction – AA, A, B, C Warning: The temperature grade for this tire is established for a tire that is properly inﬂated and not The traction grades, from highest to lowest, are AA, A, overloaded. Excessive speed, underinﬂation, or B, and C. Those grades represent the tire’s ability excessive loading, either separately or in combination, to stop on wet pavement as measured under controlled can cause heat buildup and possible tire failure.
Page 393: Used Replacement Wheels
Each new wheel should have the same load-carrying Notice: The wrong wheel can also cause problems capacity, diameter, width, offset and be mounted with bearing life, brake cooling, speedometer or the same way as the one it replaces. odometer calibration, headlamp aim, bumper height, vehicle ground clearance and tire clearance to the If you need to replace any of your wheels, wheel bolts or body and chassis.
Page 394: Tire Chains
Tire Chains If a Tire Goes Flat It’s unusual for a tire to “blowout” while you’re driving, especially if you maintain your tires properly. If air goes CAUTION: out of a tire, it’s much more likely to leak out slowly. But if you should ever have a “blowout,”...
Page 395: Changing A Flat Tire
CAUTION: CAUTION: Lifting a vehicle and getting under it to do Changing a tire can be dangerous. The vehicle maintenance or repairs is dangerous without can slip off the jack and roll over or fall on you the appropriate safety equipment and training. or other people.
Page 396: Removing The Spare Tire And Tools
Removing the Spare Tire and Tools When you have a ﬂat tire, use the following example as a guide to assist you in the placement of wheel blocks. Escalade Rear Access Panel The following information will tell you next how to use A.
Page 397 For Escalade, the equipment is located behind the left trim panel in the rear of the vehicle. Unlatch the release lever to open the trim panel door. Skip the ﬁrst step and follow the last three steps only for the Escalade. For Escalade ESV, the equipment you’ll need is under the storage tray in the left trim panel.
Page 398 1. Open the spare tire lock cover on the bumper and use the ignition key to remove the lock if your vehicle is equipped with a hoist lock (J). 2. Assemble the wheel wrench (H) and the two jack handle extensions (I) as shown. A.
Page 399 3. Insert the hoist end 5. Use the wheel wrench (open end) (F) of the hook that allows you to extension through pull the hoist cable the hole (G) in the towards you to assist in rear bumper. reaching the spare tire. 6.
Page 400: Removing The Flat Tire And Installing The Spare Tire
Removing the Flat Tire and Installing the Spare Tire Use the following pictures and instructions to remove the ﬂat tire and raise the vehicle. 1. Remove the center cap by placing the chisel end of the wheel wrench in the slot on the wheel and gently prying the cap out.
Page 401 Jack Positions (Overall View) 2. Use the wheel wrench to loosen all the wheel nuts. Turn the wheel wrench counterclockwise to loosen These locations for the front (A) and rear (B) are the wheel nuts. Don’t remove the wheel nuts yet. the general area of jack placement.
Page 402 3. Position the jack under the vehicle. CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.
Page 403 Rear Tire Flat: If the ﬂat 5. Remove all the wheel tire is on a rear tire of the nuts and take off the vehicle, you’ll need to ﬂat tire. use the jack handle (C) and both jack handle extensions (D). Attach the wheel wrench to the jack handle extensions.
Page 404 6. Remove any rust or dirt 7. Put the wheel nuts back from the wheel bolts, on after mounting the mounting surfaces spare, with the rounded and spare wheel. end of the nuts toward the wheel. Tighten each wheel nut by hand. Then use the wheel wrench to tighten the nuts until the wheel is...
Page 405 9. Tighten the nuts ﬁrmly in a crisscross CAUTION: sequence as shown by turning the wheel wrench clockwise. Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident.
Page 406: Secondary Latch System
Secondary Latch System To release the spare tire from the secondary latch, do the following: Your vehicle has an underbody-mounted tire hoist assembly equipped with a secondary latch system. It is designed to stop the spare tire from suddenly falling off your vehicle.
Page 407 4. Repeat this procedure at least two times. If the spare tire lowers to the ground, continue with Step 5 of Removing the Spare Tire and Tools on page 5-80. 5. If the spare does not lower, turn the wrench counterclockwise until approximately 6 inches (15 cm) of cable is exposed.
Page 408 11. Continue raising the jack until the spare tire stops moving upward and is held ﬁrmly in place. The secondary latch has released and the spare tire is balancing on the jack. 12. Lower the jack by turning the wheel wrench counterclockwise.
Page 409 13. Disconnect the jack handle from the jack and 14. Tilt the retainer (D) at carefully remove the jack. Use one hand to push the end of the cable against the spare while ﬁrmly pulling the jack out and pull it through from under the spare tire with the other hand.
Page 410: Storing A Flat Or Spare Tire And Tools
Storing a Flat or Spare Tire and Tools CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place. Notice: Storing an aluminum wheel with a ﬂat tire under your vehicle for an extended period of time or with the valve stem pointing up may damage the...
Page 411 1. Put the tire on the ground at the rear of the vehicle with the valve stem pointed down and to the rear of the vehicle. 2. Tilt the retainer (D) downward and through the wheel opening. Make sure the retainer is fully seated across the underside of the wheel.
Page 412 4. Insert the hoist end (F) through the hole (G) in the rear bumper and into the hoist shaft. 5. Raise the tire part way upward. Make sure the retainer is seated in the wheel opening. 6. Raise the tire fully against the underside of the vehicle by turning the wheel wrench clockwise 7.
Page 413 To store the tools, follow these procedures: 4. Use the retaining clip to fasten the tool kit on the stud in the storage compartment in the rear left trim panel For Escalade, do the following: and turn the wing nut clockwise to secure. 1.
Page 414: Spare Tire
Spare Tire Your vehicle, when new, had a fully-inﬂated spare tire. A spare tire may lose air over time, so check its inﬂation pressure regularly. See Inﬂation - Tire Pressure on page 5-67 and Loading Your Vehicle on page 4-47 for information regarding proper tire inﬂation and loading your vehicle.
Page 415: Appearance Care
Appearance Care Do not use any of these products unless this manual says you can. In many uses, these will damage the vehicle: Cleaning products can be hazardous. Some are toxic. Other cleaning products can burst into ﬂames if a match •...
Page 416: Special Fabric Cleaning Problems
Most stains can be removed with club soda water. 3. Spray a small amount of the cleaner onto a clean To clean, use the following instructions: soft, white, cloth. Do not apply spray directly to the fabric. 1. For liquids: blot with a clean, soft, white cloth. For solids: remove as much as possible and then 4.
Page 417: Vinyl
• Stains caused by oil and grease can be cleaned with Soiled or stained leather should be cleaned an approved GM cleaner and a clean, white cloth. immediately. If dirt is allowed to work into the ﬁnish, it can harm the leather. 1.
Page 418: Speaker Covers
Speaker Covers Care of Safety Belts Vacuum around a speaker cover gently, so that the Keep belts clean and dry. speaker will not be damaged. Clean spots with just water and mild soap. CAUTION: Glass Surfaces Do not bleach or dye safety belts. If you do, it Glass should be cleaned often.
Page 419: Washing Your Vehicle
Washing Your Vehicle Finish Care The paint ﬁnish on the vehicle provides beauty, depth of Occasional waxing or mild polishing of the vehicle by color, gloss retention, and durability. hand may be necessary to remove residue from the paint ﬁnish. GM-approved cleaning products can be The best way to preserve the vehicle’s ﬁnish is to keep it obtained from your dealer.
Page 420: Windshield, Backglass, And Wiper Blades
Aluminum or Chrome-Plated Wheels Exterior painted surfaces are subject to aging, weather, and chemical fallout that can take their toll over a period of years. To help keep the paint ﬁnish looking The vehicle may be equipped with either aluminum or new, keep the vehicle in a garage or covered whenever chrome-plated wheels.
Page 421: Tires
Sheet Metal Damage Use chrome polish only on chrome-plated wheels, but avoid any painted surface of the wheel, and buff off immediately after application. If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop Notice: If you drive your vehicle through an applies anti-corrosion material to parts repaired or automatic car wash that has silicone carbide tire...
Page 422: Underbody Maintenance
Underbody Maintenance Vehicle Care/Appearance Materials Chemicals used for ice and snow removal and dust See your GM dealer for more information on purchasing control can collect on the underbody. If these are not the following products. removed, corrosion and rust can develop on the Description Usage underbody parts such as fuel lines, frame, ﬂoor pan,...
Page 423: Vehicle Identiﬁcation
Vehicle Identiﬁcation Description Usage Removes swirl marks, ﬁne Swirl Remover Polish scratches, and other light Vehicle Identiﬁcation Number (VIN) surface contamination. Removes light scratches Cleaner Wax and protects ﬁnish. Cleans, shines, and Foaming Tire Shine Low protects in one step. Gloss No wiping necessary.
Page 424: Service Parts Identiﬁcation Label
Service Parts Identiﬁcation Label Windshield Wiper Fuses You will ﬁnd this label on the inside of the glove box. The windshield wiper motor is protected by an internal It is very helpful if you ever need to order parts. circuit breaker and a fuse. If the motor overheats due to On this label, you will ﬁnd the following: heavy snow, etc., the wiper will stop until the motor cools.
Page 425: Fuses And Circuit Breakers
Fuses and Circuit Breakers Instrument Panel Fuse Block The wiring circuits in your vehicle are protected from The fuse block access short circuits by a combination of fuses, circuit breakers door is located on the and fusible thermal links. This greatly reduces the driver’s side edge of the chance of ﬁres caused by electrical problems.
Page 426 Fuses Usage RR Wiper Rear Window Wiper Switch Special Equipment Option SEO ACCY Accessory WS WPR Windshield Wipers Truck Body Controller TBC ACCY Accessory IGN 3 Rear Heated Seats Module Four-Wheel Drive Switch, Air Suspension Switch/Module HTR A/C Not Used Power Door Lock Relay LOCK (Lock Function)
Page 427 Fuses Usage Fuses Usage RR FOG LP Not Used BODY Harness Connector BRAKE Brake Switch Driver Door Module Power Door Lock Relay Instrument Panel Outlets, DRIVER UNLOCK (Driver’s Door Unlock AUX PWR 2 Rear Cargo Area Power Function) Outlets Brake Transmission Shift Rear Doors and Liftgate LOCKS IGN 0...
Page 428: Center Instrument Panel Fuse Block
Center Instrument Panel Fuse Block Device Usage Special Equipment The center instrument panel utility block is located Option/Off-road Lamps underneath the instrument panel, to the left of the Harness Connector steering column. TRAILER Trailer Brake Wiring UPFIT Upﬁtter (Not Used) SL RIDE Ride Control (Not Used) HDLR 2...
Page 429: Underhood Fuse Block
Underhood Fuse Block The underhood fuse block in the engine compartment is located on the driver’s side of the vehicle near the battery. Lift the cover for access to the fuse/relay block. To remove fuses if you don’t have a fuse extractor, hold the end of the fuse between your thumb and index ﬁnger and pull straight out.
Page 430 5-114...
Page 431 Fuses Usage Fuses Usage GLOW PLUG Not Used IGN A Ignition Switch CUST FEED Gasoline Accessory Power IGN B Ignition Switch HYBRID Hybrid Left Bussed Electrical Center, LBEC 1 Left Doors, Truck Body Accessory Power/Trailer STUD #1 Controller, Flasher Module Wiring TRL PARK Parking Lamps Trailer Wiring...
Page 432 Fuses Usage Fuses Usage Vent Solenoid Canister F/PMP Fuel Pump (Relay) RR HVAC Not Used Oxygen Sensors Auxiliary Power Back-up Lamps, Automatic AUX PWR Outlet — Console B/U LP Transmission Shift Lock Control System IGN 1 PCM Ignition RR DEFOG Rear Window Defogger PCM 1 Powertrain Control Module...
Page 433 Fuses Usage Fuses Usage Daytime Running Lamps Brake Transmission Shift BTSI Interlock System Regulated Voltage Control CRNK Starting System Instrument Panel IPC/DIC Cluster/Driver Information LO HDLP-RT Headlamp Low Beam-Right Center FOG LP Not Used Climate Control FOG LP Not Used HVAC/ECAS Controller/Electronically HORN...
Page 434 Auxiliary Electric Cooling Fan Fuse Lift the cover for access to the fuse/relay block. Block Fuses Usage COOL/FAN Cooling Fan The auxiliary electric COOL/FAN Cooling Fan Relay Fuse cooling fan fuse block is COOL/FAN Cooling Fan Fuse located in the engine compartment on the driver’s side of the vehicle Relays...
Page 435: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-13 for more information. Capacities Application English Metric Air Conditioning Refrigerant See refrigerant label located in the engine compartment. Escalade Escalade ESV Cooling System Capacity...
Page 436 Capacities and Speciﬁcations Engine VIN Code Transmission Spark Plug Gap VORTEC™ 5300 V8 Automatic 0.040 inches (1.01 mm) VORTEC™ 6000 H.O. V8 Automatic 0.040 inches (1.01 mm) 5-120...
Page 437 Section 6 Maintenance Schedule Maintenance Schedule ........6-2 Owner Checks and Services ......6-9 Introduction ...........6-2 At Each Fuel Fill ..........6-9 Maintenance Requirements ......6-2 At Least Once a Month .........6-10 Your Vehicle and the Environment ....6-2 At Least Once a Year ........6-10 Using Your Maintenance Schedule ....6-2 Recommended Fluids and Lubricants ....6-13 Scheduled Maintenance ........6-4...
Page 438: Maintenance Schedule
Maintenance Schedule Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your Introduction vehicle in good working condition, but also helps the environment. All recommended maintenance is Important: Keep engine oil at the proper level and important.
Page 439 Because of all the different ways people use their vehicles, maintenance needs vary. You may need more CAUTION: frequent checks and replacements. So please read the following and note how you drive. If you have any questions on how to keep your vehicle in good condition, Performing maintenance work on a vehicle can ®...
Page 440: Scheduled Maintenance
The proper replacement parts, ﬂuids and lubricants to If the engine oil life system is ever reset accidentally, use are listed in Recommended Fluids and Lubricants you must service your vehicle within 3,000 miles on page 6-13 and Normal Maintenance Replacement (5 000 km) since your last service.
Page 441 Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and ﬁlter. See Engine Oil on page 5-13. Reset oil life system. See Engine Oil Life System on page 5-16. An Emission Control Service. Lubricate chassis components. See footnote #. Visually check for any leaks or damage.
Page 442: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Additional Required Services 25,000 50,000 75,000 100,000 125,000 150,000 Service and Miles (Kilometers) (41 500) (83 000) (125 000) (166 000)
Page 443: Maintenance Footnotes
Additional Required Services (cont’d) 25,000 50,000 75,000 100,000 125,000 150,000 Service and Miles (Kilometers) (41 500) (83 000) (125 000) (166 000) (207 500) (240 000) Replace spark plugs and inspect spark plug wires. An Emission Control Service. Engine cooling system service (or every 5 years, whichever occurs ﬁrst).
Page 444 (b) Visually inspect front and rear suspension and (f) Lubricate all key lock cylinders, hood latch assembly, steering system for damaged, loose or missing parts, secondary latch, pivots, spring anchor, release pawl, rear signs of wear or lack of lubrication. Inspect power compartment hinges, outer tailgate handle pivot points, steering lines and hoses for proper hook-up, binding, latch bolt, fuel door hinge and folding seat hardware.
Page 445: Owner Checks And Services
At Each Fuel Fill (i) Drain, ﬂush and reﬁll cooling system. This service can be complex; you should have your dealer perform this service. See Engine Coolant on page 5-23 for It is important to perform these underhood checks at what to use.
Page 446: At Least Once A Month
Engine Coolant Level Check At Least Once a Year Check the engine coolant level and add Starter Switch Check ® DEX-COOL coolant mixture if necessary. See Engine Coolant on page 5-23 for further details. Windshield Washer Fluid Level Check CAUTION: Check the windshield washer ﬂuid level in the windshield washer tank and add the proper ﬂuid if necessary.
Page 447: Ignition Transmission Lock Check
Automatic Transmission Shift Lock 3. With the engine off, turn the ignition to RUN, but do not start the engine. Without applying the regular Control System Check brake, try to move the shift lever out of PARK (P) with normal effort. If the shift lever moves out ®...
Page 448: Underbody Flushing Service
Parking Brake and Automatic • To check the PARK (P) mechanism’s holding ability: Transmission Park (P) Mechanism Check With the engine running, shift to PARK (P). Then release the parking brake followed by the regular brake. CAUTION: ® Contact your GM Goodwrench dealer if service is required.
Page 449: Recommended Fluids And Lubricants
Recommended Fluids and Usage Fluid/Lubricant Lubricants GM Power Steering Fluid Power Steering (GM Part No. U.S. 89021184, in System Canada 89021186). Fluids and lubricants identiﬁed below by name, ® DEXRON -III Automatic part number or speciﬁcation may be obtained from your Automatic Transmission Fluid.
Page 450 Usage Fluid/Lubricant Usage Fluid/Lubricant ® DEXRON -III Automatic Body Door Transmission Fluid. Look for Hinge Pins, Transfer Case “Approved for the H-Speciﬁcation” Tailgate Hinge Multi-Purpose Lubricant, Superlube on the label. and Linkage, (GM Part No. U.S. 12346241, in Folding Seats Canada 10953474).
Page 451: Normal Maintenance Replacement Parts
Normal Maintenance Replacement Parts Replacement parts identiﬁed below by name, part number or speciﬁcation can be obtained from your GM dealer. ® Part GM Part Number ACDelco Part Number Engine Air Cleaner/Filter 5300 V8 25313349 A1518C 5300 V8 (High Capacity) and 6000 V8 25313348 A1519C Oil Filter...
Page 452: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2 in this section. Any additional information from Owner Checks and Services on page 6-9 can be added on the following record pages. Also, you should retain all maintenance receipts.
Page 453 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-17...
Page 454 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-18...
Page 455 Section 7 Customer Assistance and Information Customer Assistance and Information ....7-2 Reporting Safety Defects ........7-12 Customer Satisfaction Procedure ......7-2 Reporting Safety Defects to the United States Online Owner Center ........7-4 Government ..........7-12 Customer Assistance for Text Reporting Safety Defects to the Canadian Telephone (TTY) Users ........7-4 Government ..........7-12 Customer Assistance Offices ......7-4...
Page 456: Customer Assistance And Information
Canadian Cadillac Customer Communication Centre by calling 1-888-446–2000. Your satisfaction and goodwill are important to your dealer and to Cadillac. Normally, any concerns We encourage you to call the toll-free number in order to give your inquiry prompt attention. Please have...
Page 457 STEP THREE: Both General Motors and your dealer You may contact the BBB Auto Line Program using the are committed to making sure you are completely toll-free telephone number or write them at the satisﬁed with your new vehicle. However, if you continue following address: to remain unsatisﬁed after following the procedure BBB Auto Line Program...
Page 458: Online Owner Center
To assist customers who are deaf, hard of hearing, or one place. speech-impaired and who use Text Telephones (TTYs), The Online Owner Center allows you to: Cadillac has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with • Get e-mail service reminders.
Page 459 Long Distance: 011-52-53 29 0 800 1-800-496-9994 Fax Number: 313-381-0022 Canada — Customer Assistance General Motors of Canada Limited Canadian Cadillac Customer Communication Centre, 163-005 1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7 1-888-446-2000 1-800-263-3830 (For Text Telephone devices (TTYs)
Page 460: Gm Mobility Reimbursement Program
GM Mobility Assistance service is provided at no charge for any warranty-covered Center at 1-800-323-9935. Text telephone (TTY) users, situation and for a nominal charge if the Cadillac is no call 1-800-833-9935. longer under warranty. Roadside Service is available only GM of Canada also has a Mobility Program.
Page 461 Warranty Period — 48 months/50,000 miles (80 000 km). technician, if available, can travel to your location within a 30 mile (50 km) radius of a participating Cadillac Emergency Road Service is performed on site for the dealership. If beyond this radius, we will arrange to have following situations: your car towed to the nearest Cadillac dealership.
Page 462: Courtesy Transportation
Cadillac by dialing from the United States or Canada is safety-related. If it is, please call your dealership, 1-888-889-2438 — daily, 24 hours.
Page 463: Transportation Options
Warranty service can generally be completed while you courtesy rental vehicle or reimburse you for a rental wait. However, if you are unable to wait Cadillac vehicle that you obtain if your vehicle is kept for helps minimize your inconvenience by providing several a warranty repair.
Page 464: Vehicle Data Collection And Event Data Recorders
Additional Program Information Vehicle Data Collection and Event Data Recorders Courtesy Transportation is available during the Bumper-to-Bumper warranty coverage period, but it is Your vehicle, like other modern motor vehicles, has a not part of the New Vehicle Limited Warranty. A number of sophisticated computer systems that monitor separate booklet entitled Warranty and Owner and control several aspects of the vehicle’s performance.
Page 465 Unlike the data recorders on many airplanes, these In addition, once GM collects or receives data, GM may: on-board systems do not record sounds, such as • use the data for GM research needs, conversation of vehicle occupants. • make it available for research where appropriate To read this information, special equipment is needed conﬁdentiality is to be maintained and need is and access to the vehicle or the device that stores...
Page 466: Reporting Safety Defects
Reporting Safety Defects Reporting Safety Defects to the Canadian Government Reporting Safety Defects to the If you live in Canada, and you believe that your vehicle United States Government has a safety defect, you should immediately notify Transport Canada, in addition to notifying General If you believe that your vehicle has a defect which could Motors of Canada Limited.
Page 467: Reporting Safety Defects To General Motors
Transmission, Transaxle, Transfer Detroit, MI 48232-5169 Case Unit Repair Manual In Canada, please call us at 1-888- 446-2000. Or, write: Canadian Cadillac Customer Communication Centre, This manual provides information on unit repair service 163-005 procedures, adjustments, and speciﬁcations for GM General Motors of Canada Limited transmissions, transaxles, and transfer cases.
Page 468: Service Bulletins
Service Bulletins Current and Past Model Order Forms Service Bulletins give technical service information Service Publications are available for current and needed to knowledgeably service General Motors cars past model GM vehicles. To request an order form, and trucks. Each bulletin contains instructions to please specify year and model name of the vehicle.
Page 469 Anti-Lock Brake, System Warning Light ....3-39 Appearance Care ..........5-99 Accessory Power Outlets ......... 3-21 Aluminum or Chrome-Plated Wheels ..... 5-104 Adding Equipment to Your Airbag-Equipped Care of Safety Belts ........5-102 Vehicle ............1-86 Chemical Paint Spotting ......5-106 Additives, Fuel ..........
Page 470 Audio System(s) (cont.) Brake (cont.) CD Changer ..........3-99 Brake Pedal, Throttle ........2-20 Chime Level Adjustment ......3-106 Brakes ............5-36 Diversity Antenna System ......3-106 Braking ............4-6 Navigation/Radio System ......3-96 Braking in Emergencies ........4-8 Radio with Cassette and CD ......3-70 Break-In, New Vehicle ........
Page 471 Care of (cont.) Cigarette Lighter ..........3-21 Your CDs and DVDs ........3-105 Cleaning Cargo Cover ..........2-44 Aluminum or Chrome-Plated Wheels ..... 5-104 CD Changer ........... 3-99 Exterior Lamps/Lenses ........ 5-103 Center Console Storage Area ......2-42 Fabric/Carpet ..........5-99 Center Passenger Position, Safety Belts .....
Page 472 Coolant (cont.) Surge Tank Pressure Cap ......5-26 Daytime Running Lamps ........3-15 Cooled Seats ........... 1-5, 1-10 Defensive Driving ..........4-2 Cooling System ..........5-29 Delayed Locking ..........2-9 Cruise Control Lever ........3-11 Diversity Antenna System ....... 3-106 Cruise Control Light ........
Page 473 Driving Engine (cont.) At Night ............. 4-31 Coolant ............5-23 City ............4-36 Coolant Heater ..........2-21 Defensive ............. 4-2 Coolant Temperature Gage ......3-40 Drunken ............4-2 Engine Compartment Overview ...... 5-12 Freeway ............. 4-37 Exhaust ............. 2-28 Hill and Mountain Roads ......4-39 Fan Noise ..........
Page 474 Fluid (cont.) Gage (cont.) Fog Lamps ............ 3-16 Voltmeter Gage ........... 3-37 Front Axle ............5-47 Garage Door Opener ........2-37 Fuel ............... 5-5 Gasoline Additives ............5-6 Octane ............5-5 California Fuel ..........5-6 Speciﬁcations ..........5-5 Filling a Portable Fuel Container ....5-10 Glove Box .............
Page 475 Heater ............3-22 Highbeam On Light ......... 3-47 Keyless Entry System ........2-4 Highway Hypnosis ........... 4-39 Keys ............... 2-3 Hill and Mountain Roads ........4-39 ® HomeLink Transmitter ........2-37 ® HomeLink Transmitter, Programming ....2-37 Hood Checking Things Under ........ 5-10 Labelling, Tire Sidewall ........
Page 476 Light (cont.) Low Fuel Warning ........3-48 Maintenance Schedule Low Tire Pressure Warning Light ....3-39 Additional Required Services ......6-6 Malfunction Indicator ........3-42 At Each Fuel Fill ........... 6-9 Passenger Airbag Status Indicator ....3-35 At Least Once a Month ........ 6-10 Safety Belt Reminder ........
Page 477 Mirrors (cont.) Outside (cont.) Outside Automatic Dimming Mirror with Curb Automatic Dimming Mirror with Curb View View Assist ..........2-35 Assist ............. 2-35 Outside Convex Mirror ......... 2-34 Convex Mirror ..........2-34 Outside Heated Mirrors ........ 2-34 Heated Mirrors ..........2-34 Outside Power Mirrors ........
Page 478 Power (cont.) Rear Door Security Locks ........ 2-12 Retained Accessory (RAP) ......2-19 Rear Heated Seats ......... 1-10 Seat ............1-3 Rear Safety Belt Comfort Guides ...... 1-45 Steering Fluid ..........5-34 Rear Seat Armrest .......... 2-43 Windows ............ 2-15 Rear Seat Audio (RSA) ........
Page 479 Restraint Systems (cont.) Seats Replacing Parts ........... 1-87 50/50 Split Bench Seat ......... 1-13 Retained Accessory Power (RAP) ...... 2-19 60/40 Split Bench Seat ......... 1-11 Right Front Passenger Position, Safety Belts ..1-41 Bench Seat ..........1-19 Road Sensing Suspension ......... 4-9 Bucket Seats, Rear ........
Page 480 Shifting Into Park (P) ........2-26 Shifting Out of Park (P) ........2-27 Tachometer ............ 3-33 Signals, Turn and Lane-Change ......3-8 Taillamps ............5-57 Spare Tire ............. 5-98 Theft-Deterrent, Radio ........3-102 Installing ............ 5-84 Theft-Deterrent Systems ........2-16 Removing ...........
Page 481 Tires (cont.) Storing a Flat or Spare Tire and Tools .... 5-94 Ultrasonic Rear Parking Assist (URPA) ....3-18 Tire Sidewall Labelling ........5-61 Understanding Radio Reception ....... 3-103 Tire Terminology and Deﬁnitions ....5-64 Uniform Tire Quality Grading ......5-75 Uniform Tire Quality Grading ......
Page 482 Windshield Washer ......... 3-10 Fluid ............5-35 Warning Lights, Gages and Indicators ....3-31 Windshield Wiper Warnings Blade Replacement ........5-59 DIC Warnings and Messages ......3-53 Fuses ............5-108 Hazard Warning Flashers ....... 3-6 Windshield Wipers ......... 3-9 Other Warning Devices ........3-6 Winter Driving ..........

This manual is also suitable for:

2005 escalade 2005 escalade esv

Cadillac ESCALADE ESV 2005 Owner's Manual

Section 1 Seats and Restraint Systems

Front Seats

Rear Seats

Safety Belts

Child Restraints

Airbag System

Restraint System Check

Section 2 Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Onstar System

Homelink Transmitter

Storage Areas

Sunroof

Vehicle Personalization

Section 3 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages, and Indicators

Driver Information Center (DIC)

Audio System(S)

Section 4 Driving Your Vehicle

Your Driving, the Road, and Your Vehicle

Towing

Section 5 Service and Appearance Care

Service

Fuel

Checking Things under the Hood

All-Wheel Drive

Rear Axle

Front Axle

Headlamp Aiming

Bulb Replacement

Windshield Wiper Blade Replacement

Tires

Appearance Care

Vehicle Identiﬁcation

Electrical System

Capacities and Speciﬁcations

Quick Links

Chapters

Related Manuals for Cadillac ESCALADE ESV 2005

Summary of Contents for Cadillac ESCALADE ESV 2005