NOVAK HAVOC SPORT ESC - CUSTOM PROGRAMMING AND GEARING Instructions

p R O p E R G E A R I N G & A d j u s tA b l E pA R A m E t E R s
#55-1732P-1
ATTENTION: Correct gearing is essential to getting proper performance from your brushless motor system!
P R O P E R G E A R S E L E C T I O N
Motor operating temperature is the ONLY
way to properly set the vehicle gearing
The motor should be 160-175°F MAX at end of run!
Change the gearing to avoid overheating.
Do noT Free rev or operATe wiThouT loAD!
General Gearing for 2-cell li-po or 6-Cell ni-Mh use:
These recommendations are for sport or entry level setups. Stock radio
equipment and sport "stick-type" battery packs should work safely. These gearing
recommendations are intended to provide initial safe operation.
BrUsHLEss MOTOrs
Havoc 8.5
SS8.5 Pro (Novak #3408)
SS10.5 Pro (Novak #3410)
SS13.5 Pro (Novak #3413)
SS17.5 Pro (Novak #3417)
SS21.5 Pro (Novak #3421)
Decrease the pinion tooth number by 2-3 for motors without sintered rotors.
if you do not change gearing after switching to brushless, you will be
over-geared and will have slow acceleration & excessive temperatures!
With the broad brushless power band, you can go 1-2 teeth higher pinion than listed above
for more top speed, but remember going higher will produce excessive ESC & motor heating.
Check the motor's operating temperature after making any gearing adjustments--motors are
designed to operate from 160ºF-175ºF. If you do overheat your ESC and motor, be sure to
allow it to cool for several hours and install a smaller pinion gear.
FOr rTr kITs:
Most car kits include a pinion gear that is generally sized for mild motors and
is fairly large. To be safe, replace the installed pinion gear with one that is
about 3 to 5-teeth smaller. Most stock spur gears are safe to use.
FOr TrAXXAs® sLAsH™:
With the Havoc 8.5 motor installed, the RTR kit's included 18-tooth pinion
gear will provide speeds above 30 mph with a 7-cell battery pack. The
23-tooth pinion gear included in the RTR kit will provide speeds above 40
mph with a 7-cell battery pack.*
T H R O T T L E P R O F I L E S
NOTE: The havoc's software has an Auto-Detect Brush-Mode.
This feature will automatically switch the eSC from the Brushless
Throttle Profile to Brush-Mode when it does not have a brushless
motor's sensor harness plugged into it at start-up.
BrUsHLEss PrOFILE
w/Reverse
Reverse%
Programmable
Minimum Brake%
Drag Brake
Dead Band%
Minimum Drive%
Throttle Curve
Brake Frequency
Motor rotation
Li-Po Cut-Off
The Havoc ESC reverts back to default settings when One-Touch set-up is performed.
The Havoc ESC is fully programmable, refer to page 6 for fine-tuning options.
PINION GEAr rANGE
15 through 20-tooth
15 through 20-tooth
17 through 22-tooth
20 through 27-tooth
25 through 30-tooth
28 through 33-tooth
BrUsH-MODE
1 2
on on
100% 100%
yes yes
0% 0%
off off
6% 6%
1% 1%
expo linear
on off
on off
on on
T H R O T T L E C U R v E S E L E C T I O N
100%
linear
0
Trigger position
L I - P O C U T- O F F C I R C U I T R Y
When active (see programming on reverse side to turn ON/OFF), the built-in
Smart-Stop Li-Po Cut-Off Circuitry lets you safely use Lithium Polymer
batteries by cutting off the ESC's throttle output when a critical safety
voltage is reached.
ESC's factory default is Li-Po Cut-Off Circuitry Active
The circuitry constantly monitors the pack voltage. When it gets close to
the critical safety voltage (6.25V) it begins interrupting, or 'blipping' the
throttle output as an early warning that the battery's voltage is getting
low and the throttle output will soon be completely shut off.
When the critical voltage is reached, the throttle output to the motor gets
completely shut down to keep the voltage from dropping further (Red &
Green LEDs will alternately flash & you still have steering control). re-charge
battery after Smart-Stop circuitry shuts off throttle. Even though the
pack's voltage will rise (after a short resting period) to a level high enough to
run the motor again, this is not good for Li-Po batteries—reaching the
critical safety voltage too many times can damage the cells.
Do noT ConTinue To run vehiCle AFTer The li-po CuT-oFF hAS
ShuT Down The ThroTTle ouTpuT The FirST TiMe.
During power-up when ESC is switched ON, the Amber & Red LEDs
will flash together 3 times to indicate Li-Po Cut-Off is ACTIVE.
With the Li-Po Cut-Off turned ON & using Ni-Cd or Ni-MH cells, the circuitry will shut off the ESC's
throttle output very early into the run, due to the different characteristics of these batteries. To
deactivate software, see page 6.
M O T O R R O TAT I O N S E L E C T I O N
The Havoc software lets you reverse a brushless motor's rotation
direction (see reverse side of this sheet to select rotation). This allows
installation in vehicles with counter-rotating drive trains (or opposed
transmissions), without compromising performance. Because the ESC
will be operating in its normal forward & reverse modes, features like
Smart Braking continue to operate normally.
www.teamnovak.com
*At the time of printing, the Traxxas® Slash™ RTR kit included an 18-tooth and a
23-tooth pinion gear.
Slash™ is a registered trademark of Traxxas®.
P5
Novak's Throttle Curve adjustment
allows drivers to tailor the throttle
response of a vehicle, creating
either a quick burst of power with the
Linear Curve setting, or a smoother,
controlled low-end power delivery
with the Expo Curve setting.
expo
Setting is fixed at "Linear" in
Brush Mode. The Throttle Curve
is selectable in Brushless Mode.
100%
10-2008