Advertisement
advanced -- CUSTOM programmiNG
PLEASE NOTE: This page contains optional Advanced Programming items!
(but don't worry, you can always reset factory defaults by performing the One-Touch programming again, so go ahead & experiment--that's why the programming is in there, right?)
to custom program profiles
Your transmitter can be either ON or OFF:
1. IF TRANSMITTER IS OFF, DISCONNECT ESC FROM RECEIVER
Remove input signal harness from receiver to avoid radio interference.
2. CONNECT SPEED CONTROL TO A CHARGED BATTERY PACK
3. SLIDE ESC's ON/OFF SWITCH TO 'ON' POSITION
4. MAKE SURE THROTTLE PROFILE 1-4 OR 6 IS ACTIVE
If you are not sure what profile is selected, follow the procedures in 'Throttle Profile
Selection' to check or select desired profile.
5. FOLLOW STEPS ON RIGHT SIDE OF THIS PAGE TO CUSTOMIZE ESC
You can adjust different parameters (described on back side of this sheet) for Throttle Profiles
1, 2, 3, 4, & 6 to fine tune the speed control to perform & feel the way you like it.
Remember that you can not access the Brush-Mode (Profile #6) without
disconnecting the brushless motor's sensor harness from the ESC.
Note: there is no time constraint during selection process of custom parameters.
gtb soFtware Flow chart:
@NEUTRAL
RED LED on solid
MIN. BRAKE
DRAG BRAKE
BLUE & AMBER
DEAD BAND
BLUE & GREEN
MIN. DRIVE
LiPo CUT-OFF
AMBER & RED
if Brush-Mode
is active
DRIVE FREQUENCY
GREEN
press & hold
ACTIVE PROFILE
all LEDs (flashing)
if Brush-Mode
is active
––––––
all LEDs
flash 6 times
LEDs roll off
––––
exit programming
@NEUTRAL
RED LED on solid
restoring factory defaults
Every time you perform the One-Touch Set-Up, the factory default settings
are restored for each of the throttle profiles & ESC reverts to Profile #1.
1
4
-
or
press & hold
BLUE
press & hold
press & hold
press & hold
AMBER
press & hold
press & hold
if Brushless-Mode
is active
if Brushless-Mode
is active
––––––
# of flashes equals
active profile (1-5)
if pressed
––––––
within 3 sec. of
all LEDs flashing
––––––
active profile
changed
if not pressed
––––––
within 3 sec. of
all LEDs flashing
:
:
6
to adjust minimum brake
a. PRESS & HOLD SPEED CONTROL'S SET BUTTON
With ESC at neutral, press & hold SET button until the BLUE status LED turns on
solid---Release ESC's SET button once LED is on solid.
b. SELECT MINIMUM BRAKE PERCENTAGE
Blue status LED flashes to indicate active Minimum Brake setting. Quick press & release
SET button to select desired setting.
Setting
(# of flashes)
Minimum Brake
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
When SET button is pressed & held for about 1 second, the new selection is stored in ESC's
memory--The 4 status LEDs will scroll back & forth to indicate ESC is exiting programming &
the Red (Green & Blue may also be on) LED will turn on solid--ESC is at neutral & ready to go.
to activate & adjust drag brake
a. PRESS & HOLD SPEED CONTROL'S SET BUTTON
With ESC at neutral, press & hold SET button until BLUE & AMBER status LEDs turn on
solid---Release SET button once LEDs are on solid.
b. SELECT DRAG BRAKE PERCENTAGE
Blue & Amber status LEDs flash to indicate Drag Brake setting (Min.Brake setting will be the
same as Drag Brakes). Quick press & release SET button to change Drag Brake setting.
Setting
(# of flashes)
Drag Brake
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
Selection is stored in memory--Status LEDs scroll back & forth and ESC exits programming.
Red LED turns on solid
Notes: When Drag Brakes are active, the Blue LED will also stay on during
normal operation. To re-activate the standard style of braking (no drag brakes
during neutral), repeat Minimum Brake adjustment as described above.
to adjust dead band
a. PRESS & HOLD SPEED CONTROL'S SET BUTTON
With ESC at neutral, press & hold SET button until BLUE & GREEN status LEDs turn on
solid---Release SET button once LEDs are on solid.
b. SELECT DEAD BAND PERCENTAGE
Blue & Green status LEDs flash to indicate active Dead Band setting. Quick press &
release SET button to change setting.
Setting
Dead Band
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
Selection is stored in memory--Status LEDs scroll back & forth and ESC exits programming.
Red LED turns on solid
to adjust minimum drive
a. PRESS & HOLD SPEED CONTROL'S SET BUTTON
With ESC at neutral, press & hold SET button until AMBER status LED turns on
solid---Release SET button once LED is on solid.
b. SELECT MINIMUM DRIVE PERCENTAGE
Amber status LED flashes to indicate active Minimum Drive setting. Quick press & release
SET button to change setting.
Setting
Minimum Drive
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
Selection is stored in memory--Status LEDs scroll back & forth and ESC exits programming.
Red LED turns on solid
to activate liPO cut-off circuitry
a. PRESS & HOLD SPEED CONTROL'S SET BUTTON
With ESC at neutral, press & hold SET button until AMBER & RED status LED turns
on solid---Release SET button once LEDs are on solid.
b. TURN LiPo CUT-OFF CIRCUITRY ON or OFF
Amber & Red status LEDs flash to indicate LiPo Cut-Off Circuitry setting. Quick press &
release SET button to change setting.
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
Selection is stored in memory--Status LEDs scroll back & forth and ESC exits programming.
Red LED turns on solid
to adjust drive frequency
a. PRESS & HOLD SPEED CONTROL'S SET BUTTON
With ESC at neutral, press & hold SET button until GREEN status LED turns on
solid---Release SET button once LED is on solid.
b. SELECT DRIVE FREQUENCY
Green status LED flashes to indicate active Drive Frequency setting. Quick press & release
SET button to change setting.
Setting
(# of flashes)
Drive Frequency
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
Selection is stored in memory--Status LEDs scroll back & forth and ESC exits programming.
Red LED turns on solid
P6
No further adjustments are required.
:
(using this turns off drag brakes)
:
1 2 3 4 5 6 7 8 9 10
:
0
3
6
9 12 15 18 21 24 27
(%)
blue & amber LEDs
:
1 2 3 4 5 6 7 8 9 10
:
off 3
6
9 12 15 18 21 24 27
(%)
(Green & Blue LEDs may also be on)
--ESC is at neutral & ready to go.
blue & green LEDs
:
1
2
3
(# of flashes)
(%)
:
2
3
4
--ESC is at neutral & ready to go.
(Green & Blue LEDs may also be on)
:
1
2
3
(# of flashes)
:
1
3
5
(%)
--ESC is at neutral & ready to go.
(Green & Blue LEDs may also be on)
amber & red LEDs
1 flash = OFF
--ESC is at neutral & ready to go.
(Green & Blue LEDs may also be on)
:
1
2
3
4
: 1.5
2.5
3.5
4.5
(kHz)
--ESC is at neutral & ready to go.
(Green & Blue LEDs may also be on)
blue LED
:
:
4
5
5
6
:
amber LED
4
5
8
12
:
2 flashes = ON
:
(Profile 6 ONLY)
green LED
5
6
7
6.5
8.5
11
Advertisement
