DigiTech HARDWIRE CR-7 Owner's Manual
  1. Manuals
  2. Brands
  3. DigiTech Manuals
  4. Music Pedal
  5. HARDWIRE CR-7
  6. Owner's manual

DigiTech HARDWIRE CR-7 Owner's Manual

Stereo chorus
Hide thumbs
Table of Contents

Advertisement

Quick Links

HARDWIRE CR-7
STEREO CHORUS
OWNER'S MANUAL

Advertisement

Table of Contents
loading

Related Manuals for DigiTech HARDWIRE CR-7

Summary of Contents for DigiTech HARDWIRE CR-7

  • Page 1 HARDWIRE CR-7 STEREO CHORUS OWNER’S MANUAL...

  • Page 2: Declaration Of Conformity

    Sandy, Utah 84070, USA Safety: IEC 60065 -01+Amd 1 Date: October 4, 2010 EMC: EN 55022:2006 European Contact: Your local DigiTech Sales and Service EN 55024:1998 Office or FCC Part 15 Harman Signal Processing Supplementary Information: 8760 South Sandy Parkway...
  • Page 3 WARNING If you want to dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery, and recycling. For your protection, read the following: Private households in the 25 member states of the EU, in Switzerland and Norway may return their used electronic product free of charge to designated collection facilities or to a retailer (if you Important Safety Instructions...
  • Page 4 7. The foregoing is in lieu of all other warranties, expressed or implied, and DigiTech neither assumes nor authorizes any person to assume any obligation or liability in connection with the sale of this product. In no event shall DigiTech or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control.
  • Page 5 If you notice a change in the LED’s brightness, or the pedal will not switch from Bypass to Effect, replace the battery with a new 9-Volt alkaline battery or visit your local DigiTech dealer to obtain a power adapter and unleash the pedal’s full potential with unlimited power.

  • Page 7: Included Items

    Introduction More than a remarkable achievement, DigiTech’s HardWire series represents ® a collection of significant improvements in guitar effects pedals. The HardWire series pedals provide a suite of well-known effects, each with superior tone and control. But these pedals go above and beyond their peers to provide such...
  • Page 8 Pedal Interface...
  • Page 9 What Does This Do? 1. Level Knob - Controls the chorus level. Turn this knob clockwise to increase and counter-clockwise to decrease the chorus level. 2. DC Adapter Jack - Connect the optional Harman power supply to this jack. Use the proper supply for your area’s mains line voltage. 3.
  • Page 10 5. Type Knob - The Type knob selects one of the seven chorus types: • STUDIO – Studio quality chorus with a wide stereo image. • MULTI – True 8-voice chorus; the lushest chorusing you can get in a pedal. •...
  • Page 11 7. Input 2 - Connect a second input to this jack for stereo operation. Inputs 1 and 2 are processed separately through the stereo chorus effect and then fed to Outputs 1 and 2 keeping true stereo separation between channels. 8.
  • Page 12 11. Output 1 (Mono) - Connect this output to the input of a single guitar amplifier, another pedal input, or an amp effects return. 12. Output 2 - Connect this output to a second guitar amplifier when two amplifiers are being used. Note: Use unbalanced mono instrument cables only.
  • Page 13 Amp Setup Harman Power Supply (optional)
  • Page 14 Effects Loop Setup AMP RETURN Harman Power Supply (optional) AMP SEND Note: If the amp effects loop has a mix control, set the mix to 100% full wet.
  • Page 15 Battery Operation In the event that battery power is completely depleted, HardWire pedals automatically switch into bypass. This eliminates the need to remove the pedal from your pedal chain if the battery is dead. To replace the battery, do the following: 1.
  • Page 16 into place over the depressed pin. Release the pin. When the Foot Switch is properly fastened, both Release Pins are flush with the outer side of Foot Switch the pedal. Pedal Switch 9VDC Battery Foot Switch Release Pin Battery Compartment Foot Switch Spring Release Pin...
  • Page 17 Performance Accessories The performance accessories make integrating a HardWire pedal into any pedal board a snap. The following accessories are included: • Hook-and-loop Pedalboard Pad (designed to attach to the surfaces found on most commercial pedal boards) • Foot Switch Glow Sticker (easily visible on dark stages) •...
  • Page 18 Hook-and-loop Pedalboard Pad To attach the Pedalboard Pad, do the following: 1. Peel off the existing rubber skid pad from the bottom of the pedal. 2. Peel the adhesive protector from the back of the Pedalboard Pad. 3. Apply the Pedalboard Pad to the bottom of the pedal.
  • Page 19 Foot Switch Glow Sticker To attach the Foot Switch Glow Sticker, do the following: 1. Peel the adhesive backing from the Foot Switch Glow Sticker. 2. Apply the Glow Sticker to the top of the Foot Switch.
  • Page 20 StompLock To place the StompLock over the pedal knobs, do the following: 1. Set the knobs to your preferred setting. 2. Gently push the StompLock over the top of the knobs. 3. To remove the StompLock, gently lift one side and then the other.

  • Page 21: Specifications

    Specifications Controls: Level, Speed, Depth, Type, On/Off Pedal Jacks: Input 1 (Mono), Input 2, Output 1 (Mono), Output 2 Input Impedance: >1 MΩ (stereo), >500 kΩ (mono) - effect on Output Impedance: 1 kΩ - effect on Input Impedance: True hardwire bypass - effect off Output Impedance: True hardwire bypass - effect off Power Supply:...
  • Page 24 8760 South Sandy Parkway Sandy, Utah 84070 PH (801) 566-8800 FAX (801) 566-7005 DigiTech and HardWire ® ® registered trademarks of Harman Designed in the USA Copyright - Harman Printed in China HardWire CR-7 Owners Manual 5024335-B Please visit our website at: www.digitech.com...

Table of Contents