Pioneer HTP-2600 Quick Start Manual

HTP-2500/2600 Quick Start Guide
Check that you have all the
1
accessories.
STANDBY/ON
SLEEP STATUS
Speaker cord (x1) INPUT SELECTOR
DIGITAL STB DVD/DVR
FM/AM TAPE/VCR TV
TUNING
– + –
SYSTEM
SETUP VOLUME
+
FM wire antenna
ENTER
ROOM
SETUP
–
AUTO SURROUND
OFF SOUND TONE
Batteries (x2)
BASS TREBLE
– + –
RECEIVER
AM loop
Remote control
antenna
Brackets (x4)
You should also have:
• Speakers (x5)
Screws (x4)
• Subwoofer
Non-skid pads • Operating instructions
(1x20, 1x4)
• Warranty card
4
Connect antennas
Connect the FM wire antenna and fully extend along a
1
window frame or another suitable place that gives good
reception.
To connect the AM loop antenna, twist the exposed wire
2
strands together and insert into the terminal, then snap
the connector shut as shown below.
AM loop
antenna
FM wire antenna
ANTENNA
FM
UNBAL
75Ω
AM
LOOP
3/8 in.
(10mm)
For detailed instructions, see the Operating Instructions supplied and / or contact one of our knowledgeable Pioneer Customer Service Representatives at 1 - (800) 421-1404.
Put the batteries in the remote
2
control and stick the non-skid pads
to the base of the speakers.
MUTE
Open the battery compartment on
1
DIMMER the rear of the remote control.
TUNER
EDIT
CLASS
Insert the supplied batteries
2
STATION
+
following the markings inside the
CH LEVEL
battery compartment to align
them correctly.
TEST
TONE
STEREO 3 Replace the battery compartment
cover.
MPX
+
4 Stick the self-adhesive non-skid
pads to the underside of each
speaker, and to the underside of
the subwoofer. Use four pads per
speaker (see below).
Front and surround speakers Center speaker
Connect the receiver to your DVD
5
player/ recorder.
Use a coaxial digital cord (not supplied) to connect the digital
1
output of your DVD player/ recorder to the DIGITAL INPUT
(COAXIAL) DVD/DVR jack.
Use a red/white stereo audio cord (not supplied) to connect the
2
AUDIO TV IN jack on the receiver to the audio output on your
TV.* This will allow you to listen to your TV through this
speaker system.
* Note that you must also connect the DVD player/ recorder's
video output to your TV's video input to watch a DVD video
(video cable is not supplied).
DIGITAL INPUT
(COAXIAL)
DVD/DVR
Receiver
AUDIO
TV IN
+ +
IN
OUT
– –
R L
DIGITAL VIDEO
OUT OUT
DVD player/ recorder
Connect each speaker to the receiver using the
3
supplied speaker wires.
To connect, insert the colored wire into the matching colored (+) tab
and the other wire into the black (–) tab as shown below. Connect the
center speaker the same way (matching the wire the color-coded label).
Note that the color-coded tabs are as follows:
• Red : Front right speaker
• White : Front left speaker
• Green : Center speaker
SPEAKERS
FRONT SUB
R L CENTER
WOOFER
+
–
For the best surround sound, set up your
speakers like this. The front left and right
speakers should be about 6–9 feet apart.
Subwoofer
Plug the receiver, DVD player/
6
recorder and TV into a convenient
AC outlet.
1
Press STANDBY/ON to switch on the receiver.
STANDBY/ON
STANDBY/ON
Switch on your DVD player/ recorder and TV, and set the TV to
2
the correct video input.
Receiver
STANDBY/ON
R L
VIDEO AUDIO
TV
IN OUT
STANDBY/ON
DVD player/ recorder
Surround right
• Purple : Subwoofer
• Grey : Surround right speaker
• Blue : Surround left speaker
Receiver
SURROUND
R L
+
–
Front right
After switching on, make any
7
necessary settings required by the
DVD player/ recorder, then you're
ready to start enjoying your home
theater system.
Refer to the receiver's operating instructions for a detailed
explanation of this system's surround sound features.
VOLUME
+
–
Receiver
VIDEO 1
VIDEO SELECT
TV
Surround left
Listening position
Subwoofer
Center Front left
INPUT SELECTOR
AUTO SURROUND STEREO
DIGITAL STB DVD/DVR
FM/AM TAPE/VCR TV