Pioneer BDP-09FD - Elite Blu-Ray Disc Player Operating Instructions Manual page 67

Problem Check
Is Output Terminal properly set?
Sound and picture are not
synchronized.
Is Lip Sync properly set?
• No sound is output. Is the disc played back in slow motion?
• Sound is not output Is the disc played back in fast forward or fast reverse?
properly.
Are the audio cables properly connected?
Is the audio cable damaged?
Are the connected components (AV receiver or amplifier, etc.)
properly set?
Is Output Terminal properly set?
Is the output video resolution properly set?
Is the AV receiver or amplifier, etc., connected to the AUDIO
OUT (7.1 ch) terminals?
Are the speakers properly set?
Is Pure Audio set to Mode 1 or Mode 2?
Is a DVI device connected?
Are you playing a DTS-CD?
Multi-channel sound is not Is Output Terminal properly set?
output.
Is the AV receiver or amplifier connected to the HDMI OUT
(SUB) terminal?
Is the audio output of the connected AV receiver or amplifier,
etc., properly set?
Is multi-channel sound selected?
Is the AV receiver or amplifier, etc., connected to the AUDIO
OUT (7.1 ch) terminals?
Noise can be heard when Is the connected AV receiver or amplifier compatible with DTS
outputting DTS Digital Digital Surround?
Surround signals from the
DIGITAL OUT terminals.
192 kHz or 96 kHz digital
audio signals cannot be
output from the DIGITAL
OUT terminals.
Is HDMI Audio Out properly set?
Secondary audio or
interactive audio is not
output.
Are Dolby Digital Out and DTS Out properly set?
Remedy
Set Output Terminal properly (pages 21 and 44).
Adjust the amount of audio delay with the Lip Sync setting
(page 42).
No sound is output during slow motion play and forward and
reverse scanning.
• Connect the cable properly according to the connected
devices (page 15).
• Insert the cable firmly and all the way in.
If the cable is damaged, replace it with a new one.
Read the operating instructions of the connected components
and check the volume, input, speaker settings, etc.
When ANALOG AUDIO is selected at Output Terminal, no
audio signals are output from the HDMI OUT or DIGITAL OUT
terminals (page 44).
Use OUTPUT RESOLUTION to switch to the resolution at
which the video and audio signals are output (page 25).
To listen to 2-channel analog audio, connect to FRONT (L/R) of
the AUDIO OUT (7.1 ch) terminals (page 14) and set Audio
Output Mode to 2 Channel (page 45).
When the AV receiver or amplifier, etc., is connected to the
AUDIO OUT (7.1 ch) terminals and Audio Output Mode is
set to Multi-channel, set Speaker Setup properly (page 47).
If set to Mode 1 or Mode 2, signals are only output from the
output terminal set at Output Terminal (page 53).
The sound will not be output from the HDMI OUT terminals if a
DVI device is connected. Connect the device to a DIGITAL OUT
terminals or the AUDIO OUT (7.1 ch) terminals (page 18).
To output the sound of DTS-CDs from the HDMI OUT (SUB)
terminal, set HDMI Audio Out to PCM (page 45).
For some BDs, audio signals are only output from DIGITAL
OUT terminals or the HDMI OUT terminals.
Linear PCM (2-channel) audio signals are output from output
terminals other than the one set at Output Terminal under
Audio Out. Set Output Terminal properly (page 44).
The HDMI OUT (SUB) terminal outputs linear PCM 2-channel
audio signals. Be sure to connect the AV receiver or amplifier
to the HDMI OUT (MAIN) terminal.
Read the operating instructions of the connected AV receiver
or amplifier and check the audio output settings of AV receiver
or amplifier.
Use the menu screen or AUDIO to switch the disc's sound to
multi-channel.
When the AV receiver or amplifier, etc., is connected to the
AUDIO OUT (7.1 ch) terminals, set Audio Output Mode to
Multi-channel (page 45). Also, set Speaker Setup properly
(page 47).
If an AV receiver or amplifier that is not compatible with DTS
Digital Surround is connected to the DIGITAL OUT terminals,
set DTS Out to DTS  PCM (page 44).
It is not possible to output 192 kHz or 96 kHz digital audio
signals from this player's DIGITAL OUT terminals. The signals
are automatically converted to 48 kHz or less for output.
When listening to the sound from an HDMI OUT (MAIN)
terminal, set HDMI Audio Out to PCM (page 45).
When listening to the sound from an DIGITAL OUT terminal,
set Dolby Digital Out to Dolby Digital 1, DTS Out to DTS 1
(page 44).
07
67
En