Graco 8402L04 - SnugRide Infant Car Seat Base User Manual
Graco 8402L04 - SnugRide Infant Car Seat Base User Manual

Graco 8402L04 - SnugRide Infant Car Seat Base User Manual

Adjustable infant restraint base
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

Adjustable Infant Restraint Base
Base with LATCH
See infant restraint owner's manual for
complete installation instructions.
Your new infant restraint base is equipped with Graco's recline adjustment foot, which helps to properly recline the infant
restraint/base on the vehicle seat. Use it AFTER you have carefully followed all of the steps in your infant restraint owner's
manual.
ecline the infant restraint/base on the vehicle seat. Use it AFTER you have carefully followed all of teps in
your infant restraint owner's
The adjustable base is used along with the level indicator on the side of your infant restraint. To check the proper angle of
the infant restraint, first make sure the vehicle is on level ground and that the infant restraint/base is not tilted sideways on
the vehicle seat. Then check the level indicator. You must look straight on at the indicator.
If the indicator shows ONLY blue, the infant restraint is properly leveled.
If any orange is showing in the level indicator, the infant restraint is
either too upright or too reclined.
To lower the foot: pull down on the bottom of the foot to the desired
setting to adjust the recline
To raise the foot: set the base on a flat surface, push in on the fingers
on the base and push down on the base to adjust the recline
If there is still orange in the level indicator when the foot is completely
extended then place a rolled towel under the foot until ONLY blue shows.
Tighten belt through base, then reinstall infant restraint. Level indicator
should now show ONLY blue—if you still see orange, re-adjust recline
© 2002 Graco 447-4-02
.
You must read and understand both the owner's
manual from the infant restraint and these
instructions before using the infant restraint and
base. Keep this sheet with the instruction booklet
in the pocket of your infant restraint for reference.
This base can only be used with a Graco
Infant Restraint.
If you do not have instructions for your infant
restraint or if you have any questions about
your product, call Graco at 1-888-224-6549 or
visit our website at www.gracobaby.com.
.
.
1
®

Advertisement

Table of Contents
loading

Summary of Contents for Graco 8402L04 - SnugRide Infant Car Seat Base

  • Page 1 Your new infant restraint base is equipped with Graco’s recline adjustment foot, which helps to properly recline the infant restraint/base on the vehicle seat. Use it AFTER you have carefully followed all of the steps in your infant restraint owner’s manual.
  • Page 2 Installing the Base Using Vehicle Belt 1. Place the base in a rear-facing position in a forward-facing vehicle seat Belt MUST go under tongue 2. Thread the vehicle seat belt through the openings in the base . Buckle the seat belt. The seat belt should not be twisted.
  • Page 3: Latch Locations

    LATCH locations Newer vehicles have one or more seating positions with LATCH anchorage systems. If vehicle is equipped with LATCH, the vehicle lower anchor points may be visible at the vehicle seat crease. If not visible, they may be marked with the symbol below Typical seat in a passenger vehicle.
  • Page 4: Storing Latch

    Storing LATCH Storage bars 1. For ease of storing, extend LATCH to its maximum length. 2. Locate the storage bars on bottom of infant restraint base 3. Fasten end of LATCH (without adjustment belt) onto storage bar. 4. Repeat Step 3 for LATCH with adjustment belt.
  • Page 5 La base de su nuevo sistema de seguridad para niños está equipada con el pie Graco de ajuste inclinable que ayuda a reclinar debidamente la base/sistema de seguridad sobre el asiento del vehículo. Úselo DESPUÉS de haber seguido detenidamente todos los pasos en el manual del propietario de su sistema de seguridad para niños.
  • Page 6 Instalación de la base usando el cinturón del vehículo 1. Coloque la base orientada hacia atrás en un asiento del vehículo orientado hacia adelante El cinturón DEBE pasar debajo de la lengüeta. 2. Pase el cinturón del asiento del vehículo por las aperturas de la base .
  • Page 7: Utilización Del Latch Para Instalar La Base

    Las ubicaciones del sistime LATCH Los vehículos nuevos tienen uno o varios asientos equipados con sistemas de anclaje LATCH. Si el vehículo viene equipado con LATCH, se pueden ver los puntos de anclaje inferiores en el pliegue del asiento del vehículo. Si no están visibles, pueden estar Un asiento típico de un vehículo de pasajeros.
  • Page 8: Almacenamiento Del Latch

    Almacenamiento del LATCH Barras de almacenamiento 1. Para facilitar el almacenamiento, extienda el LATCH hasta el máximo. 2. Ubique las barras de almacenamiento en el fondo de la base del sistema de seguridad 3. Ajuste el extremo del LATCH (sin el cinturón de ajuste) sobre la barra de almacenamiento.

This manual is also suitable for:

840301 - snugride840303 - snugride840305 - snugride

Table of Contents