Troubleshooting Chart; Maintenance - Sharp XL-HF201P User Manual

Troubleshooting chart (continued)
■ USB
Symptom
● Device cannot be
detected.
● Playback does not
start.
● Wrong time display.
● Wrong file name
display.
■ iPod, iPhone or iPad
Symptom
● No sound is
produced.
No image appears
on the TV/monitor.
● iPod, iPhone or
iPad will not
charge.
● "This accessory is
not made to work
with iPhone" or
"This accessory is
not supported by
iPhone" appears on
iPhone screen.
■ Condensation
Sudden temperature changes, storage or operation in an
extremely humid environment may cause condensation
inside the cabinet (CD pickup, etc.) or on the transmitter on
the remote control. Condensation can cause the unit to
malfunction. If this happens, leave the power on with no
disc in the unit until normal playback is possible (about 1
hour). Wipe off any condensation on the transmitter with a
soft cloth before operating the unit.
■ If problem occurs
When this product is subjected to strong external
interference (mechanical
electricity, abnormal supply voltage due to lightning, etc.)
or if it is operated incorrectly, it may malfunction.
Possible cause
● Is there any MP3/WMA file
available?
● Is the device properly
connected?
● Is it an MTP device?
● Does the device contain
AAC file only?
● Is it a copyright protected
WMA file?
● Is it a false MP3 file?
● Is Variable Bitrate file being
played back?
● Is the File Name written in
Chinese or Japanese
characters?
Possible cause
● The iPod, iPhone or iPad is
not playing.
● The iPod, iPhone or iPad is
not properly connected to
the unit.
● Is the AC power lead of the
unit plugged in?
● The video cable is not
properly connected.
● The TV/monitor's input
selection is not properly set.
● The iPod TV out feature has
not been set to output video.
● USB terminal do not support
video.
● The iPod, iPhone or iPad is
not making full contact with
the connector.
● Using iPod (3 rd
generation).
● The iPod or iPhone is not
supported. Refer to page 7
for compatible models.
● The iPhone battery is low.
Please charge the iPhone.
● iPhone is not properly
docked.
shock, excessive
If such a problem occurs, do the following:
1
Set the unit to the stand-by mode and turn the power on
again.
2
If the unit is not restored in the previous operation,
unplug and plug in the unit again, and then turn the
power on.
Note:
If neither operation above restores the unit, clear all the
memory by resetting it.
■ Factory reset, clearing all memory
1
Press the ON/STAND-BY button to enter the power
stand-by mode.
2
Whilst pressing down the OPEN/CLOSE button, press
the ON/STAND-BY button until "Clear All" appears.
Caution:
This operation will erase all data stored in memory
including clock, timer settings and tuner preset.
■ Before transporting the unit
Remove the iPod, iPhone, iPad, USB memory device and
disc from the unit. Then, set the unit to the power stand-by
mode. Carrying the unit with iPod, iPhone, iPad or USB
memory device left connected or discs left inside might
damage the unit.
■ Care of compact discs
Compact discs are fairly resistant to damage, however
mistracking can occur due to an accumulation of dirt on the
disc surface. Follow the guidelines below for maximum
enjoyment from your CD collection and player.
● Do not write on either side of the disc, particularly the
non-label side from which signals are read. Do not
mark this surface.
● Keep your discs away from direct sunlight, heat, and
excessive moisture.
● Always hold the CDs by the edges. Fingerprints, dirt, or
water on the CDs can cause noise or mistracking. If a
CD is dirty or does not play properly, clean it with a soft,
dry cloth, wiping straight out from the centre, along the
radius.
NO

Maintenance

■ Cleaning the cabinet
Periodically wipe the cabinet with a soft cloth and a diluted
soap solution, then with a dry cloth.
Caution:
● Do not use chemicals for cleaning (petrol, paint thinner,
etc.). It may damage the cabinet.
● Do not apply oil to the inside of the unit. It may cause
static
malfunctions.
E-21
YES
Correct