Desa VK42N SERIES Owner's Operation And Installation Manual page 25

OPERATING FIREPLACE
Continued
OPTIONAL HAND-HELD
REMOTE OPERATION
Note: All remote control accessories must be purchased sepa-
rately (see Accessories, page 36). Follow instructions included
with the remote control.
NOTICE: You must light the pilot before using the
hand-held remote control unit. See Lighting Instruc-
tions, page 24.
1. After lighting, let pilot flame burn for about one minute.
Turn control knob to ON position. Adjust flame adjust-
ment knob anywhere between HI and LO. Slide the selec-
tor switch to the REMOTE position (see Figure 51). Note:
The burner may light if hand-held remote was on when
selector switch was last turned off. You can now turn the
burner on and off with the hand-held remote control unit.
IMPORTANT: Do not leave the selector switch in the REMOTE
or ON position when the pilot is not lit. This will drain the battery.
Blower Control Knob
(Optional Accessory)
Selector
Switch in
Remote
Position
Figure 51 - Setting the Selector Switch, Gas Control Knob, and
Variable Control Knob for Remote Operation
ON/OFF SERIES MODELS GHRCB
Hold the control button on the hand-held remote until burner
turns on. Hold the control button again until burner turns off
(see Figure 52).
press both buttons on hand-held remote control until
TO LOCK
light stops flashing. Hand-held remote control is now locked. If
the fire is on it will be turned off automatically. In the locked
state, the light will not light up when any button is pressed.
press both buttons together on hand-held remote
TO UNLOCK
control until the light stops flashing. The hand-held remote is
now unlocked.
Figure 52 - On/Off Hand-Held Remote Control Unit GHRCB
For more information, visit www.desatech.com
For more information, visit www.desatech.com
111921-01A
Gas Control
Knob in ON
Variable
Position
Control Knob
OFF
ON
Control Button
Turns Burners
On and Off
OPERATING FIREPLACE
Optional Hand-Held Remote Operation
THERMOSTAT SERIES MODELS GHRCTB
The hand-held remote can be operated using either the manual mode
(MANU) or thermostatic mode (AUTO) (see Figure 53). To select
Fahrenheit/Centigrade mode display, carefully press the ˚C/˚F mode
button with the end of a paper clip or similar blunt object.
Manual Mode
1. Press the POWER and LOCK buttons together to turn on
the hand-held remote control.
2. Press the MANU button to turn on the fireplace.
3. Press the POWER and LOCK buttons together to turn off
the fireplace.
Auto (Thermostatic) Mode
1. Press the POWER and LOCK buttons together to turn on
the hand-held remote control.
2. Press AUTO button to select this mode.
3. Set the desired room temperature by pressing the TEMP
+ or - buttons.
4. Press the POWER and LOCK buttons together to turn off
the fireplace
Note: Do not leave the hand-held remote in the AUTO mode
close to the fireplace. The radiant heat from the fireplace will
turn off the fireplace. Ideally, place the hand-held remote in the
center of the room facing towards the fireplace.
Note: Do not hold the hand-held remote for a long time. Body
temperature will affect its operation in the AUTO mode.
Digital Display
Shows
Temperature and
Settings
Turns Burners
On or Off
Decreases Room
Temperature in
AUTO Mode
Figure 53 - Thermostat Hand-Held Remote Control Unit
Selections GHRCTB
Safety Features
When away from home for an extended period of time or as a child
safety feature to prevent accidental ignition of the fireplace, the
receiver ON/OFF/REMOTE switch should be in the OFF position.
Auto Shutoff Feature
1. If the average room temperature exceeds 82 degrees Fahr-
enheit (28 degrees Centigrade), the hand-held remote con-
trol will perform a safety override and shut the fireplace
off. This feature is not available in the MANU mode.
25
25
Turns Hand-Held
Remote On or Off
and Allows You to
Choose the Manual
Setting
Selects Auto
Setting
Increases Room
Temperature in
AUTO Mode
Locks System to
Prevent Accidental
Ignition