Kenmore 4433 - Pro 23.1 cu. Ft Installation Instructions

TO BE REMOVED BY THE CUSTOMER AFTER INSTALLATION iS COMPLETE.
f
[]
[]
[]
iNSTALLATiON CHECKOFF LiST
Doors
[] Handles are secure and tight
[] Door seals completely to cabinet on all sides
[] Doors are level across the top
Leveling
[] Refrigerator is level, side to side and tilted 1/4" (6mm) front to back
[] Toe grille is properly attached to refrigerator
[] Cabinet is setting solid on all corners
Electrical Power
House power turned on
Refrigerator plugged in
ice Maker
[] House water supply connected to refrigerator
[] Water & power couplings connected at door
[] No water leaks present at all connections - recheck in 24 hours
[] Ice Maker is turned ON.
[] Ice & Water Dispenser operates correctly
[] Front filter must be flush with filter housing (some models)
Final Checks
[] Shipping material removed
[] Fresh Food and Freezer controls set
[] Crisper Humidity controls set
[] Registration Card sent in
.o o.°o,!, c.,o M.°u,i
I additional information about your refrigerator!
Tools You Will Need:
1
HAND TRUCKING
, Load refrigerator from side of cabinet
only.
• Do not run retaining straps over
handles.
Do not over-tighten retaining straps.
Never use refrigerator handles to
move the refrigerator.
• Remove tape from doors only after
unit is in place. .J
INSTALLATION CLEARANCES
Allow the following clearances for ease of installation,
proper air circulation, and plumbing and electrical
connections:
• Sides &Top .......... 3/8"
Back ....................... 1"
NOTE: If you are installing your refrigerator beside a wall,
leave 1/2" minimum between hinges and wall to allow for
the door to swing open.
J
Ensureicemakeris turned ON. Togain access to the ice maker,
slide the ice cream tray out. Check to see that the Ice & Water
Dispenser is operating correctly. (See Automatic Ice & Water
Dispenser Features in Use & Care Manual.)
J
SHIPPING MATERIAL
1 PIECE OF FOAM
OR CARDBOARD
2 WIRE TIES [_tc:_-
(All wire basket _ '_
will have 2 wire
ties)
......... 1 PIECE OF TAPE
............ 1 PIECE OF TAPE OR
.... 2 BLUE SHIPPING CLIPS
1 PIECE OF TAPE
........... SHELF SPACER WITH TOE GRILLE
1 PIECE OF TAPE
.... 3 PIECES OF TAPE
......... 1 PIECE OF TAPE
Remove Shipping material. 'Features may vary per model.)
f
LEVELING AND ADJUSTING
All four corners of refrigerator must rest firmly on a solid
floor.Your refrigerator has adjustable rollers to help level it
F
3
WATER SUPPLY ....
Connect water supply - check for water leaks. Turn icemaker OFF
if water supply is not connected immediately. Connecting to a
reverse osmosis system is not recommended.
J
and to adjust the doors.
To level cabinet or change door height:
1. Remove toe grille.
2. Use a screwdriver, 3/8" wrench, or nutdriver to adjust the
rollers.To raise cabinet or door, turn screw clockwise. To
lowercabinet or door, turn screw counterclockwise.
%.,
Cabine_
: od
L, ii o ve. I
__Door ]L DOOR _j
Door -. Water
• -." Line
Hinge
Assembly Screws
If you need to remove the doors to get your refrigerator in the house, please See
Door Removal Instructions in your Use & Care Manual.
When changing
control settings,
wait 24 hours before making additional adjustments.
9
%
_/ See"Normal Operating Sights & Sounds" in the Use & Care
Manualso you understand the sounds you may hear once
your refrigerator is running.
_/ Please read entire Use & Care Manualto become aware of
important safety instructionsand to become familiar with your
new refrigerator.
_/ Send in Registration card to register your refrigerator.
",] Congratulations! You are ready to enjoy your new refrigerator.
J
IFYOU ARE DISSATISFIED WITH THE INSTALLATION OFYOUR REFRIGERATOR, PLEASE CALLTHE STORE YOU PURCHASED IT FROM. P/N: 2 41582502