Cateye CYCLOCOMPUTER CC-RD300W User Manual

CATEYE STRADA WIRELESS
CYCLOCOMPUTER CC-RD300W
Before using the computer, please thoroughly read this manual and keep it for
future reference.
WARNING / CAUTION
• Do not concentrate on the computer while riding. Ride safely!
• Install the magnet, sensor, and bracket securely. Check these periodically.
• If a child swallows a battery, consult a doctor immediately.
• Avoid having the computer in direct sunlight for unnecessary or extended periods.
• Do not disassemble the computer.
• Do not drop the computer. Doing so may result in a computer malfunction or damage.
• When using the computer installed on the bracket, change the MODE by pressing on the three dots below
the screen. Pressing hard on other areas can result in malfunction or damage to the computer.
• Tighten the dial on the Flex-Tight bracket by hand only. Over-tightening can damage the bracket
threads.
• When cleaning the computer, bracket and sensor, do not use thinners, benzene, or alcohol.
• Dispose of used batteries according to local regulations.
• LCD screen may be distorted when viewed through polarized sunglass lenses.
Wireless Sensor
The sensor was designed to receive signals within a maximum range of 70 cm, to reduce chance of
interference.
When adjusting the wireless sensor, note the following:
• Signals cannot be received if the distance between the sensor and the computer is too great.
• The transmission distance may be shorter due to low temperature or low battery.
• Signals can be received only when the back of the computer is facing the sensor.
Interference may occur, resulting in incorrect data, if the computer is:
• Near a TV, PC, radio, motor, or in a car or train.
• Close to a railroad crossing, railway tracks, TV stations and/or radar base.
• Using with other wireless devices in close proximity.
This device complies with Part 15 of the FCC Rules.Operation is subject to the following
two conditions:(1)This device may not cause harmful interference,and (2)this device
must accept any interference received,including interference that may cause undesired
operation.
Modifications The FCC requires the user to be notified that any changes or modifications
made to this device that are not expressly approved by CatEye Co.,Ltd.May void the user
's authority to operate the equipment.
Preparing the computer
Battery case cover
MENU
AC
MODE
: Speed unit
: Wheel size icon
: Sensor signal reception icon
1
Clear all data (initialization)
Press the AC button on the back.
2
Select the desired speed units
Select " " or " ".
km/h ↔ mph
Register the
setting
MENU MENU
MODE MODE
3
Enter the tire circumference
Enter the tire circumference of your bicycle in mm.
* Refer to the tire circumference reference table.
Move digits
Increase
(by pressing
& holding)
MENU
MENU MENU
MODE MODE
MODE
MODE MODE
4
Set the clock
When MODE is pressed and held, "Displayed
time", "Hour", and "Minute" will appear, in
this order.
Switch the
24h ↔ 12h,
screen or
or increase
move digits
the value
(by pressing
MENU MENU
MODE MODE MODE
MODE MODE
& holding)
Tire circumference
reference table
Tire size
12 x 1.75
14 x 1.50
14 x 1.75
16 x 1.50
16 x 1.75
18 x 1.50
18 x 1.75
When the computer is
20 x 1.75
20 x 1-3/8
mounted on the bracket
22 x 1-3/8
22 x 1-1/2
Push!
24 x 1
24 x 3/4 Tubular
24 x 1-1/8
24 x 1-1/4
24 x 1.75
24 x 2.00
24 x 2.125
26 x 7/8
26 x 1 ( 59 )
26 x 1 ( 65 )
26 x 1.25
26 x 1-1/8
26 x 1-3/8
26 x 1-1/2
26 x 1.40
26 x 1.50
AC
26 x 1.75
26 x 1.95
26 x 2.00
26 x 2.10
26 x 2.125
26 x 2.35
26 x 3.00
27 x 1
27 x 1-1/8
27 x 1-1/4
27 x 1-3/8
650 x 20C
650 x 23C
650 x 35A
650 x 38A
650 x 38B
700 x 18C
700 x 19C
700 x 20C
700 x 23C
700 x 25C
Register
700 x 28C
the setting
700 x 30C
700 x 32C
700C Tubular
700 x 35C
700 x 38C
700 x 40C
29 x 2.1
29 x 2.3
Measure wheel
circumference (L) of your bike
To get the most accurate
calibration do a wheel roll out.
Register
W i t h t h e v a l v e s t e m
the setting
perpendicular to the ground,
(finish)
mark the pavement at the valve
stem. With the riders weight
on the bike, roll the wheel one
tire revolution in a straight line
and mark the ground when the
valve stem is perpendicular to
the ground again. Measure the
distance in millimeters. This is
the most accurate wheel
calibration number.
How to install the unit on your bicycle
2
3
1
6
Install the sensor and magnet
A
The distance between the computer
and the sensor must not exceed the
transmission range of 70 cm. The back
of the computer must face the sensor.
YES! NO!
Max
L (mm)
70 cm
935
1020
1055
1185
1195
1340
1350
1515 1
Install the sensor
1615
1770
1785
1753 3
1785
1795
1905
5
1890
1925
1965
1920
1913
* Install the sensor as close to the upper
1952
part of the front fork as possible.
1953
1970
3
2068 Attach the bracket to the stem or handlebar
2100
2005
When attaching the bracket to the stem
2010
2023
2050
2
2055
1
2068
2070
2083
2170
2145
2155
2161
Caution:
2169
1938
Make sure that the back of the computer faces the sensor.
1944
* The computer may not function appropriately on some stem if its back does not
2090
2125
face the sensor as shown in
2105
2070
When attaching the bracket to the handlebar
2080
2086
2096
2105
2136 1
2146
2155
2130
2168
2180
2200
2288
4
Remove/install the computer
2326
Click
* After installation, rotate the front wheel gently to check that the speed is displayed on the
computer. If the speed is not displayed, check that conditions
been done appropriately.
L mm
U.S. Pat. Nos. 5236759/6957926 Pat./Design Pat. Pending
Copyright© 2007 CATEYE Co., Ltd.
CCRD3W-070727 066600540 4
4 1 Bracket band
2 Bracket
3
Speed sensor
5
4 Magnet
5 Sensor rubber pad
6 Bracket rubber pad
7 Nylon ties (x2)
7
B
The magnet
must pass
through the
sensor zone.
Inside of right front fork
C
The clearance
between the
4
sensor surface
and the magnet
must not
exceed 5 mm.
Inside of right front fork
Pull
securely
7
6
.
A
6
Handlebar
2
While supporting it by hand,
push it out as if lifting the front up
ENG
Sensor zone
4
3
3
2
Install the magnet
Spoke
4
Toward the
sensor zone
Stem
Cut
Caution:
Round off the cut edge of the
bracket band to prevent injury.
, , and , above, have
A B C