Specifications & Technical Data - CABASSE Antigua MT30 Owner's Manual

e n g l i s h
ge over the connections on one only of the
rect phase, the image should be distinctly located between the
loudspeakers with a slight loss of bass and low midrange level.
If the image is confused and not centrally located and there is a
drastic loss of bass and low midrange level, recheck your connec-
tions.
HOME THEATER CONNECTIONS WITH
AN ACTIVE SUBWOOFER
Subwoofer positioning
With a crossover point below or around 150 Hz, the installa-
tion position of subwoofers is not limited as human ears and
brains are not able to identify the emitting point of such low
frequencies. To get the best result, it is recommended to try dif-
ferent positions and choose the one giving the best response
in the low frequencies, taking into account the room acoustics.
Hooking up the subwoofer
2 possibilities are offered to connect the subwoofer with your
system:
■ the low level one requiring the use of the
8
and LINE OUT terminals and shielded coaxial connectors,
the high level one requiring the use of the FROM RECEI-
■
9 0
VER and TO SPEAKERS
speaker cables.
The inputs are stereo ones, the mix of the
low frequencies being done by the amplifier of the subwoofer.
If the input signal is already mono, only one input
(right) should be used.
Interconnections with the Cinch
8
and LINE OUT connectors
■ Connections to the LINE IN
If your preamplifier or your integrated amplifier is fitted with
a stereo low-level output, then connect its
loudspeakers. If in cor-
7
Cinch RCA LINE IN
terminals and standard loud-
L (left) and R (right)
L (left) or R
7
RCA LINE IN
7
L (left) and R (right)
outputs to the L (left) and R (right)
woofer. If your amplifier offers a one mono output, connect it
to either the L (left) or the R (right)
Connections from the LINE OUT
■
The signal from the L (left) and R (right)
tors is the one being brought in by the
7
IN connectors filtered at 40 Hz. These outputs can thus
be used to bring the signal to the amplifier powering the main
loudspeaker.
Interconnections with the
Connections to FROM RECEIVER
■
If the preamp section of your Hi Fi or audio-video system is not
fitted with a low level output, you should then connect the
subwoofer by using its loudspeaker terminals. When connec-
ting the L (left) and R (right) speaker outputs of your amplifier
9
to the FROM RECEIVER plugs of the
not to cross (-) and (+) cord of either
nel. Such a phase inversion might damage your main amplifier.
Connections TO SPEAKERS
■
These outputs can be used to bring the signal to the main
loudspeaker systems.
The signal from the L (left) and R (right)
plugs is the one being brought in by the FROM RECEIVER
connectors. These outputs can thus be used to bring the signal
to the main loudspeaker systems.
Power supply
-
The AC in cord must be connected to the mains to supply
the subwoofer. The selection of the right voltage 115 V - 230 V
=
is done with 115 V - 230 V . Switch
or ON. With the switch on the STAND BY
mute after a few minutes without input signal. The system
turns on automatically when signal comes back.
SPECIFICATIONS & TECHNICAL DATA
MT30 Position
ANTIGUA in wall
in wall
ANTIGUA booksheft/
main speaker stand
TOBAGO floorstanding
main speaker
JERSEY floorstanding
main speaker
SOCOA on/under
center* screen
PICO booksheft/
surround on wall
ALDERNEY floorstanding
main speaker
ORION floorstanding
active subwoofer
* Magnetic shielding
9
LINE IN inputs of the sub-
9
subwoofer LINE IN inputs.
8
8
LINE OUT connec-
L (left) and R (right) LINE
speaker terminals
9
plugs
subwoofer, be careful
L (left) or R (right) chan-
0
plugs
0
TO SPEAKERS
9
q
POWER , on STAND BY
position, the unit will
Ways Drivers complement
2 1 tweeter DOM36
1 x 17 cm 17T15
2 1 tweeter DOM36
1 x 17 cm 17TD15
2 1 tweeter DOM36
2 13 cm 13TD15
x
2 1 tweeter DOM36
2 17 cm 17TD15
x
2 1 tweeter DOM36
2 13 cm 13TD15TV
x
2 1 tweeter DOM36
2 13 cm 13TD15
x
3 1 tweeter DOM36
1 13 cm 13TD15M
x
2 x 17 cm 17TD15
1 1 x 21 cm 21MT3