Advertisement
FM wire antenna
The iPod & iPhone and VOLUME + buttons have a tactile dot.
Tuning in to a preset station
Setting the clock
Check that the preset mode is selected.
1
1
Press FM to turn on the radio.
Plug in the unit.
2
2
Press TUNE/PRESET or to
Press and hold CLOCK until the hour
select the desired preset number.
flashes in the display.
3
The hour starts to flash in the display.
Adjust the volume using
3
Press ALARM/CLOCK + or – repeatedly
VOLUME + or –.
to set the hour.
Manual tuning
4
Press CLOCK.
Check that the manual mode is selected.
5
Repeat steps 3 and 4 to set the minute,
1
Press FM to turn on the radio.
and then press CLOCK.
2
Press TUNE/PRESET or to
The seconds start incrementing from zero.
Notes
tune in to a desired frequency.
If you do not press any button for about 1
3
Adjust the volume using
minute while setting the clock, the clock setting
VOLUME + or –.
will be canceled.
When pressing any of the rear buttons, hold the
Tuning in to a station
unit firmly to prevent slippage.
The unit automatically scan FM stations.
Check that the manual mode is selected.
To change the display to the daylight
AC power
saving time (summer time) indication
1
adaptor
Press FM to turn on the radio.
Change the daylight saving time (summer time)
2
Press and hold TUNE/PRESET or
adjustment setting according to the following
.
procedures.
: scans upward through the frequency
Press DST/SUMMER TIME.
bands.
" " appears in the display and the time indication
: scans downwards through the
changes to the daylight saving time (summer
frequency bands.
time).
Scanning starts from the currently-tuned
To deactivate the daylight saving time (summer
frequency. When a station is received,
time) adjustment, press DST/SUMMER TIME
scanning stops.
again. " " disappears.
3
Adjust the volume using
VOLUME + or –.
Setting the brightness
of the display
Improving the
reception
Four levels of brightness are available by pressing
SNOOZE/BRIGHTNESS.
FM: Extend the FM wire antenna fully to increase
reception sensitivity.
Notes on radio reception
Keep digital music players or mobile phones
Playing the radio
away from the FM antenna, as this may lead to
reception interference.
When you are listening to the radio with an
There are two ways to tune.
iPhone connected to the unit, interference with
To switch between the two tuning methods
radio reception may occur.
(manual tuning or preset), press TUNE MODE/
When you are listening to the radio while
ENTER MEMORY.
charging an iPod, interference with radio
Preset tuning
reception may occur.
Do not place the FM anttena close to the AC
You can preset 20 stations for FM.
power adaptor as noise may result.
1
Press FM to turn on the radio.
2
Press and hold FM until "AP" appears in
the display.
Playing an iPod
3
Press
.
TUNE MODE/ENTER MEMORY
The unit automatically presets the available
You can enjoy iPod audio by connecting to this
channels in order.
unit. To use an iPod, refer to the user's guide of
your iPod.
If a station cannot be preset
If you are using an iPhone or iPhone 3G, attach
automatically
the supplied universal dock adaptor for iPhone or
You need to preset a station with a weak signal
iPhone 3G before inserting into the connector.
manually.
The adaptor number, or , is shown on the
Check that the manual mode is selected.
bottom-rear of the supplied universal dock
1
Follow steps 1 and 2 in "Manual tuning"
adaptors. is for the iPhone, and is for the
to tune the frequency you wish to preset.
iPhone 3G. Check the adaptor number before use.
2
Press and hold
TUNE MODE/ENTER
Universal dock adaptor
MEMORY
for preset number until the
flashes.
3
Press TUNE/PRESET or to
select the preset number, then press
.
TUNE MODE/ENTER MEMORY
The frequency is stored with the selected
preset number.
Example: The following display appears
when you preset FM 105.7 MHz to preset
number 2 for FM.
The display shows the frequency for about 10
seconds, and then returns to the current time.
To preset another station, repeat these steps.
Note
If you try to store another station with the same
preset number, the previously stored station will
be replaced.
Notes
When inserting an iPod into the unit, be sure to
use the universal dock adaptor supplied with
your iPod or commercially available from
Apple Inc.
The connector of the unit is exclusively for use
with an iPod.
Sony cannot accept responsibility in the event
that data recorded on an iPod is lost or
damaged when using an iPod connected to this
unit.
For details of environmental conditions for
operating your iPod, check the website of Apple
Inc.
1
Attach the adaptor for your iPod/iPhone.
2
Insert your iPod/iPhone into the
connector of the unit.
3
Press iPod & iPhone .
The iPod begins to play automatically.
You can operate the connected iPod by this
unit or the iPod buttons.
4
Adjust the volume using VOLUME + or
–.
To
Press
Turn off the iPod
OFF, or press and
hold iPod &
iPhone
Pause playback
iPod & iPhone
To resume play,
press it again.
Go to the next track
Go back to the previous
*
track
Locate a point while
(forward) or
listening to the sound
(backward)
while playing and
hold it until you
find the point.
Locate a point while
(forward) or
observing the display
(backward)
in pause and hold
it until you find
the point.
* During playback, this operation goes back to
the beginning of the current track. To go back
to the previous track, press twice.
Notes
When placing or removing the iPod, hold the
iPod at the same angle as that of the connector
on this unit, and do not twist or bend the iPod
as connector damage may result.
Do not carry the unit with an iPod set on the
connector. Doing so may cause a malfunction.
When placing or removing the iPod, hold the
iPod firmly so as not to topple the unit.
Before disconnecting the iPod, pause playback.
To use the unit as a battery charger
You can use the unit as a battery charger.
Charging begins when the iPod is connected to
the unit.
Charging status appears in the iPod display. For
details, see the user's guide of your iPod.
On copyrights
iPod is a trademark of Apple Inc., registered in
the U.S. and other countries.
iPhone is trademark of Apple Inc., registered in
the U.S. and other countries.
All other trademarks and registered trademarks
are of their respective holders. In this manual,
™
®
and
marks are not specified.
To confirm an alarm time setting
Setting the alarm
Turn off the "ALARM" indicator in the display,
and press the ALARM ON/OFF button once.
This clock radio is equipped with 3 alarm
modes—iPod, radio and buzzer. Before setting the
To change an alarm setting
alarm, make sure to set the clock (see "Setting the
Set the alarm again.
clock").
To doze for a few more minutes
To set the alarm
Press SNOOZE/BRIGHTNESS.
The sound turns off but will automatically come
1
Press and hold ALARM SET.
on again after about 10 minutes.
"WAKE-UP" appears, and the hour flashes in
You can change the snooze time by pressing
the display.
SNOOZE/BRIGHTNESS repeatedly within
2
Press ALARM/CLOCK + or – repeatedly
4 seconds.
until the desired hour appears.
The maximum length of the snooze time is
To cycle the hour rapidly, press and hold
60 minutes.
ALARM/CLOCK + or –.
To stop the alarm
3
Press ALARM ON/OFF.
Press ALARM RESET OFF to turn off the alarm.
The minute flashes.
The alarm will sound again at the same time the
4
Repeat step 2 to set the minute.
next day.
5
Press ALARM ON/OFF.
To deactivate the alarm
The alarm mode setting is entered.
Press ALARM ON/OFF to turn off the "ALARM"
6
Press ALARM/CLOCK + or – repeatedly
indicator from the display.
until the desired alarm mode flashes.
You can choose one of 3 settings: "iPod", "FM"
Note on the alarm in the event of a power
or "BUZZER. " Set the alarm mode as follows:
interruption
– iPod: see " Setting the iPod alarm. "
In the event of a power interruption, the alarm
– FM: see " Setting the radio alarm. "
will work until the battery is totally discharged.
– BUZZER: see " Setting the buzzer alarm. "
However, certain functions will be affected as
Setting the iPod alarm
follows:
The backlight will not light up.
1
Perform steps 1 to 6 in "To set the
If the alarm mode is set to iPod or radio, it will
change to BUZZER automatically.
alarm. "
If a power interruption occurs while the alarm
2
Press ALARM ON/OFF to select "iPod"
is sounding, the alarm will stop.
alarm mode.
If ALARM RESET OFF is not pressed, the
"VOL" appears in the display.
alarm will sound for about 5 minutes.
3
Press ALARM/CLOCK + or – to adjust
If " " appears in the display, the alarm will
the volume.
not sound in the event of power interruption.
Replace the battery if " " appears.
4
Press ALARM ON/OFF.
The snooze function will not work.
The setting is entered.
During a power interruption, the alarm will
5
If "ALARM" does not appear in the
sound at the set time only once.
display, press ALARM ON/OFF again.
The iPod will sound at the set time.
Setting the sleep timer
When using an iPod touch/iPhone
To wake up to music stored in an iPod touch/
You can fall asleep to the music, etc., using the
iPhone, connect the iPod touch/iPhone to the
built-in sleep timer that turns off the unit
unit first, follow the steps above to set alarm
automatically after a preset duration.
time, and then select the music function.
Even if the iPod alarm setting is complete, if
1
Press SLEEP while the unit is turned on.
you turn the iPod touch/iPhone power off
"SLEEP" appears and the sleep time flashes in
before the unit, the iPod alarm will not work.
the display.
2
Setting the radio alarm
Press SLEEP to set the sleep timer
duration.
1
Perform steps 1 to 6 in "To set the
Each time you press SLEEP, the duration (in
alarm. "
minutes) changes as follows:
2
Press ALARM ON/OFF to select "FM"
90
60
30
alarm mode.
OFF
"FM", "PRESET" number or "– –" flashes.
"– –" is the last station received.
The display returns to clock mode for about
3
Press ALARM/CLOCK + or – to select
4 seconds after you have finished the duration
setting and released SLEEP, and then the sleep
the desired preset number or "– –".
timer starts.
4
Press ALARM ON/OFF.
The unit will play for the duration you set, and
"VOL" appears in the display.
then shut off.
5
Press ALARM/CLOCK + or – to adjust
To turn off the unit before the preset
the volume.
time
6
Press ALARM ON/OFF.
Press ALARM RESET OFF.
7
If "ALARM" does not appear in the
To change the sleep timer setting
display, press ALARM ON/OFF again.
You can press SLEEP repeatedly to select the
The radio will turn on at the set time.
desired sleep timer setting even after the sleep
Setting the buzzer alarm
timer has been activated.
1
Perform steps 1 to 6 in "To set the
To deactivate the sleep timer
Press SLEEP repeatedly to set the sleep timer to
alarm. "
"OFF" in step 2.
2
Press ALARM ON/OFF to select
"BUZZER" alarm mode.
The setting is entered.
3
If "ALARM" does not appear in the
display, press ALARM ON/OFF again.
The buzzer will sound at the set time.
Note
The volume cannot be set for the buzzer alarm.
15
Hide quick links:
Advertisement
