JVC XL-PG3B - XL PG3 CD Player Instructions

Power Supply Preparations
The illustration of the grip band is omitted.
Using the AC adaptor (not supplied)
Using dry-cell batteries
(not supplied)
AC power outlet
AC adaptor
Two "AA" (LR6) alkaline batteries.
Caution:
Do not forcibly open the battery lid too wide.
Battery indicator
Battery indicator
Notes:
This indicator appears when the batteries are almost out of power.
• Even if the unit is turned off, small power is consumed as long
Power will be cut off a short while later.
as the AC adaptor is connected to the AC power outlet.
• When you want to purchase the AC adaptor, see page 5.
Note:
Turning off the Anti-Shock Protection EX will save the battery power
more or less. For details, see "Anti-shock Protection EX" on page 4.
Preventing Accidental Operation (Hold mode)
This function causes the unit to ignore, accidental button presses. • When the unit is in Hold mode, "HoLd" and "
follows.
Hold mode prevents the following:
Power on : " " stays lit.
• Powering on the unit accidentally (which can cause the batter- Power off : "HoLd" and " " lights up for a few seconds
ies to go dead). when 6 is pressed.
• Play being cut off unexpectedly.
Note:
To use the Hold mode
If the HOLD switch is set to the ON position, you cannot turn on
HOLD
the unit.
OFF ON
• To prevent the unit from powering on accidentally, set the
HOLD switch to the ON position while the unit is turned off.
• To prevent the unit from unexpected operation during play,
set the HOLD switch to the ON position after you starts play-
ing the disc.
2
Basic Play
The illustration of the grip band is omitted.
Follow the steps in the numerical order.
3
HOLD
OFF ON
4
VOLUME
6
VOLUME
Operation
During play,
To pause
During play,
To stop
" lights as
While stopped,
To turn off the
unit
Skip function
During play,
Fast forward/
reverse
Search function
Keep depressed during play.
3
5
• Play stops automatically
when all the tracks have
been played.
1
Firmly connect
2 Label side
R L
For your reference:
Button Display/reference
"dISC"
This indication appears if 3/8 is pressed when no disc is loaded
or if the disc is not properly seated.
07
00 18
"– –"
Preparation period before playing the track
Press again to restart play. Flashes for several seconds after pressing 3/8 to play.
Total number of tracks
"OPEn"
This indication appears when the lid is open.
10
44 48
Removing discs
Turn off the unit and, after the disc has stopped rotating, remove
the disc as shown below:
Total playing time.
No indication
• To skip back to the previous track, quickly press 4
twice.
Reverse
• During Program play, the button is used to fast for-
ward or back through the programmed sequence of
Auto power off
tracks.
If the unit is left in stop mode for 30 seconds, the unit turns
• During Random play, the skip button cannot be used
Forward itself off automatically to prevent the batteries from running
to skip back to tracks that were played previously in
down.
the random sequence.
Disc rotation noise
The portable CD player uses a power-saving operation method
so that disc rotation noise will intermittently be emitted. But, it
is not a failure.
Other Play Methods
Intro play Program play
You can successively play the first 10 seconds of every track. You can program up to 32 tracks in any desired order including
the same tracks.
1
Track number in play
While stopped,
1
While stopped,
INTRO
MODE
01
02 53
(Repeatedly)
2
Elapsed playing time of Track number to be programmed
each track 00: Not programmed yet.
2
Select the desired track.
To cancel
Press MODE repeatedly until "INTRO" goes out.
Notes:
• You can also select Intro play during playback.
In this case, Intro play will start from the next track after the
current track has finished.
• You can also select Intro play during Program play mode.
3
Random play
During playback,
RAND
MODE
(Repeatedly)
The track is registered.
After playing all tracks, the unit stops.
4
Repeat steps 2 and 3.
To cancel
When you program exceeding 32 tracks, the program se-
Press MODE until "RAND" goes out, or press 7 to stop the disc.
quence number returns to "01" and will overwrite the previ-
ous setting.
Notes:
5
• You can also select Random play in stop mode.
• During Program play, you can not select Random play.
• To confirm the program
While stopped, press PROGRAM repeatedly. At this time, you
can change the program, if required.
• To delete the entire program
Turn off the unit.
4
Repeat play
You can repeat one track or all tracks.
During playback,
ALL
MODE
PROG
PROGRAM
00
01 (Repeatedly)
1 track repeat All track repeat
To cancel
Press MODE repeatedly until the repeat indicator goes out.
Program sequence
number
Notes:
• You can also select Repeat play during Program play.
• You can also select Repeat play while stopped.
PROG Hyper-Bass Sound effect
03
01
You can enjoy powerful bass sound.
OFF 1 2 HBS 1
e.g. Track number 3 HBS
PROG Anti-Shock Protection EX
PROGRAM 00
02
This function achieves excellent performance against sound inter-
ruption caused by vibrations. You will be able to enjoy listening
to music during (not vigorous) jogging.
Next program sequence number
By utilizing the high-performance servo circuit, audio data will be
stored in the memory ahead of time (up to 45 seconds worth).
Normally, this function is in effect.
ANTI SHOCK
ANTI
indicator
SHOCK
As the audio data is gradually stored, the indicator changes as follows:
[Fully stored]
To cancel
A.S.P
The "ANTI SHOCK" indicator goes out.
To activate again
Press the ASP button.
Notes:
• During this operation, the disc rotates at a higher rate than usual
in order to collect extra audio data. This may cause the batteries
to run out faster and could result in a slight increase in disc rota-
tion noise.
• This function can be switched ON and OFF during playback.
However, this may cause a slight interruption in the sound be-
cause the disc's rotational speed changes.