Asus V2-PH1 Manual
  1. Manuals
  2. Brands
  3. Asus Manuals
  4. Desktop
  5. V2-PH1
  6. Manual
Asus V2-PH1 Manual

Asus V2-PH1 Manual

Barebone system
Hide thumbs Also See for V2-PH1:
Table of Contents

Advertisement

Quick Links

Vintage2-PH1
Barebone System

Advertisement

Table of Contents
loading

Related Manuals for Asus V2-PH1

Summary of Contents for Asus V2-PH1

  • Page 1 Vintage2-PH1 Barebone System...
  • Page 2 Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.

  • Page 3: Table Of Contents

    Table of contents Notices ....................vi Safety information ................vii About this guide .................viii System package contents ..............x Chapter 1: System Introduction Welcome! ................1-2 Front panel ................1-2 Rear panel ................1-4 Voltage selector ..............1-6 Internal components ............. 1-7 Chapter 2: Basic Installation Preparation ................
  • Page 4 Creating a bootable floppy disk ......5-2 5.1.2 ASUS EZ Flash utility ..........5-3 5.1.3 AFUDOS utility ............5-4 5.1.4 ASUS CrashFree BIOS 2 utility ........ 5-6 5.1.5 ASUS Update utility ..........5-8 BIOS setup program ............5-11 5.2.1 BIOS menu screen ..........5-12 5.2.2...
  • Page 5 Table of contents Main menu ................5-14 5.3.1 System Time ............5-14 5.3.2 System Date ............5-14 5.3.3 Legacy Diskette A ..........5-14 5.3.4 Primary, Third and Fourth IDE Master/Slave ..5-15 5.3.5 IDE Configuration ..........5-16 5.3.6 System Information ..........5-18 Advanced menu ..............

  • Page 6: Notices

    Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation.

  • Page 7: Safety Information

    Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected.

  • Page 8: About This Guide

    This guide contains the following parts: Chapter 1: System introduction This chapter gives a general description of the ASUS Vintage 2 - PH1. The chapter lists the system features, including introduction on the front and rear panel, and internal components.

  • Page 9: Conventions Used In This Guide

    Refer to the following sources for additional information and for product and software updates. ASUS Websites The ASUS websites worldwide provide updated information on ASUS hardware and software products. Refer to the ASUS contact information. Optional Documentation Your product package may include optional documentation, such as warranty flyers, that may have been added by your dealer.

  • Page 10: System Package Contents

    Check your Vintage2-PH1 system package for the following items. If any of the items is damaged or missing, contact your retailer immediately. Item description ASUS Vintage2-PH1 barebone system with • ASUS motherboard • 300 W PFC power supply unit • ASUS chassis Cable •...
  • Page 11 Chapter 1 This chapter gives a general description of the ASUS Vintage2-PH1. The chapter lists the system features including introduction on the front and rear panel, and internal components. ASUS Vintage2-PH1...

  • Page 12: Chapter 1: System Introduction

    Thank you for choosing the ASUS Vintage2-PH1! The ASUS Vintage2-PH1 is an all-in-one barebone system with a versatile home entertainment feature. The system comes in a stylish mini-tower casing and powered by the ASUS motherboard that supports the Intel Pentium...
  • Page 13 USB 2.0 devices such as a mouse, printer, scanner, camera, PDA, and others. Headphone port. This Line In (green) port connects a headphone with a stereo mini-plug. Microphone port. This Mic (pink) port connects a microphone. ASUS Vintage2-PH1...

  • Page 14: Rear Panel

    Rear panel The system rear panel includes the power connector and several I/O ports that allow convenient connection of devices. Power connector. This connector is for the power cable and plug. Voltage selector. This switch allows you to adjust the system input voltage according to the voltage supply in your area.
  • Page 15 Front Speaker Out Front Speaker Out Pink Mic In Mic In Mic In Mic In Orange • Rear Speaker Out Rear Speaker Out Rear Speaker Out Black • • • Side Speaker Out Gray • • Center/Subwoofer Center/Subwoofer ASUS Vintage2-PH1...

  • Page 16: Voltage Selector

    Voltage selector The PSU has a 115 V/230 V voltage selector switch located beside the power connector. Use this switch to select the appropriate system input voltage according to the voltage supply in your area. If the voltage supply in your area is 100-127 V, set this switch to 115 V. If the voltage supply in your area is 200-240 V, set this switch to 230 V.

  • Page 17: Internal Components

    BUZZ TSB43AB22A AAFP SPDIF_OUT IE1394_2 USB56 USB78 Front panel cover ASUS motherboard 5.25-inch optical drive bays Chassis fan Hard disk drive bay 10. PCI Express x16 slot Floppy disk drive bay 11. PCI slots Power supply unit 12. PCI Express x1 slot CPU socket 13.
  • Page 18 Chapter 1: System introduction...
  • Page 19 Chapter 2 This chapter provides step-by- step instructions on how to install components in the system. ASUS Vintage2-PH1...

  • Page 20: Chapter 2: Basic Installation

    Preparation Before you proceed, make sure that you have all the components you plan to install in the system. Basic components to install 1. Central processing unit (CPU) 2. DDR Dual Inline Memory Module (DIMM) 3. Expansion card(s) 4. Hard disk drive 5.

  • Page 21: Removing The Side Cover And Front Panel Assembly

    Swing the front panel assembly to the right, until the hinge-like tabs on the right side of the assembly are exposed. Remove the front panel assembly, then set aside. Air duct Assembly hooks Chassis tab holes ASUS Vintage2-PH1...

  • Page 22: Central Processing Unit (Cpu)

    CPU socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components. ASUS will shoulder the cost of repair only if the damage is shipment/ transit-related. •...
  • Page 23 (B). Position the CPU over the socket, CPU notch making sure that the gold triangle is on the bottom-left corner of the socket then fit the socket alignment key into the CPU notch. Gold triangle mark Alignment key ASUS Vintage2-PH1...

  • Page 24: Installing The Cpu Fan And Heatsink Assembly

    Apply Thermal Interface Material on the CPU before reinstalling the heatsink and fan assembly. DO NOT eat the Thermal Interface Material. If it gets into your eyes or touches your skin, make sure to wash it off immediately, and seek professional medical help.
  • Page 25 Place the heatsink on top of the installed CPU, making sure that the four fasteners match the holes on the motherboard. When the fan and heatsink assembly is in place, connect the CPU fan cable to the connector on the motherboard. ASUS Vintage2-PH1...

  • Page 26: Installing A Dimm

    Install only identical (the same type and size) DDR memory modules. • Install only ASUS-certified memory modules. Visit the ASUS website (www.asus.com) for the latest memory Qualified Vendors List. • Always install DIMMs with the same CAS latency. For optimum compatibility, we recommend that you obtain memory modules from the same vendor.

  • Page 27: Installing A Ddr2 Dimm

    DIMM. DDR2 DIMM notch Support the DIMM lightly with your fingers when pressing the retaining clips. The DIMM might get damaged when it flips out with extra force. Remove the DIMM from the socket. ASUS Vintage2-PH1...

  • Page 28: Expansion Slots

    Expansion slots In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support. Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components.

  • Page 29: Standard Interrupt Assignments

    When using PCI cards on shared slots, ensure that the drivers support “Share IRQ” or that the cards do not need IRQ assignments. Otherwise, conflicts will arise between the two PCI groups, making the system unstable and the card inoperable. ASUS Vintage2-PH1 2-11...

  • Page 30: Pci Express X1 Slot

    2.6.3 PCI Express x1 slot This motherboard supports PCI Express x1 network cards, SCSI cards and other cards that comply with the PCI Express specifications. The figure shows a network card installed on the PCI Express x1 slot. 2.6.4 PCI slots The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI...

  • Page 31: Installing An Optical Drive

    Pin 1 on the IDE interface. Audio cable Connect one end of the audio IDE ribbon cable cable to the 4-pin connector at the back of the optical drive. Power cable ASUS Vintage2-PH1 2-13...
  • Page 32 Connect the other end of the IDE ribbon cable to the Primary IDE connector (labeled PRI_IDE) on the motherboard. See page 4-4 for the location of this connector. Connect the other end of the audio cable to the black 4-pin connector labeled CD on the motherboard.

  • Page 33: Installing A Hard Disk Drive

    With the HDD label side up, carefully insert the drive into the 3.5-inch bay and push the drive into the bay until its screw holes align with the holes on the drive bay. Secure the drive with two screws on both sides. ASUS Vintage2-PH1 2-15...
  • Page 34 Serial ATA cable Serial ATA power cable Connect one end of the Serial ATA cable to the SATA connector at the back of the drive, then connect the other end to a Serial ATA connector on the motherboard. See page 4-6 for the location of the Serial ATA connectors.
  • Page 35 If you install two IDE hard disk drives, connect the black interface of the IDE ribbon cable to the IDE connector on the second (Slave) IDE hard disk drive. Connect a 4-pin power plug from the power supply unit to the power connector at the back of the drive(s). ASUS Vintage2-PH1 2-17...

  • Page 36: Installing A Floppy Disk Drive

    Installing a floppy disk drive The Vintage2-PH1 system comes with one 3.25-inch drive bay for a floppy disk drive. To install a floppy disk drive: Remove the front panel cover. For instructions on how to remove the front panel cover, refer to page 2-3 of section “2.3 Removing the side plates and front cover”...

  • Page 37: 2.10 Re-Connecting Cables

    PWRLED IDE LED PWR_LED+ IDE_LED+ Requires an ATX power supply. System panel connector Connect the reset button, power switch, power LED, and HDD LED cables to their respective leads in the system panel connector on the motherboard. ASUS Vintage2-PH1 2-19...

  • Page 38: Removing The Bay Covers And Reinstalling The Front Panel Assembly And Side Cover

    2.11 Removing the bay covers and reinstalling the front panel assembly and side cover If you installed an optical and/or floppy disk drive, remove the bay cover(s) on the front panel assembly before reinstalling it to the chassis. To do this: Locate the bay cover locks.
  • Page 39 Chapter 3 This chapter helps you power up the system and install drivers and utilities from the support CD. ASUS Vintage2-PH1...

  • Page 40: Chapter 3: Starting Up

    Screen display and driver options may not be the same for other operating system versions. • The contents of the support CD are subject to change at any time without notice. Visit the ASUS website for updates. Chapter 3: Starting up...

  • Page 41: Running The Support Cd

    If Autorun is NOT enabled in your computer, browse the contents of the support CD to locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run the CD. ASUS InstAll - Installation Wizard for Drivers Automatically installs all the necessary drivers for this motherboard. QFE Update...

  • Page 42: Utilities Menu

    Utilities menu The Utilities menu shows the applications and other software that the motherboard supports. ASUS InstAll - Installation Wizard for Utilities Automatically installs all available utilities on this motherboard. ASUS PC Probe II This smart utility monitors the fan speed, CPU temperature, and system voltages, and alerts you of any detected problems.

  • Page 43: Manuals Menu

    ASUS Update The ASUS Update utility allows you to update the motherboard BIOS in a Windows environment. This utility requires an Internet connection either ® through a network or an Internet Service Provider (ISP). See page 3-7 for details. ASUS Screen Saver Installs the ASUS screen saver.

  • Page 44: Asus Contact Information

    3.3.4 ASUS Contact information Click the Contact tab to display the ASUS contact information. You can also find this information on the inside front cover of this user guide. Chapter 3: Starting up...

  • Page 45: Software Information

    file that came with the software for more information. 3.4.1 ASUS Update The ASUS Update is a utility that allows you to update the motherboard BIOS. This utility requires an Internet connection either through a network or an Internet Service Provider (ISP).
  • Page 46 From the FTP site, select the BIOS version that you wish to download. Click Next. The BIOS ROM information is displayed. Click Flash to update the BIOS. If you selected the option to update the BIOS from a file, a window pops up prompting you to locate the file.

  • Page 47: Asus Pc Probe Ii

    Autorun feature. If Autorun is not enabled in your computer, browse the contents of the support CD to locate the setup.exe file from the ASUS PC Probe II folder. Double-click the setup.exe file to start installation.
  • Page 48 Button Function Opens the Configuration window Opens the Report window Opens the Desktop Management Interface window Opens the Peripheral Component Interconnect window Opens the Windows Management Instrumentation window Opens the hard disk drive, memory, CPU usage window Shows/Hides the Preference section Minimizes the application Closes the application Sensor alert...

  • Page 49: Hardware Monitor Panels

    Click to You can also adjust the threshold increase values using the Config window. value You cannot adjust the sensor Click to decrease threshold values in a small value monitoring panel. ASUS Vintage2-PH1 3-11...

  • Page 50: Dmi Browser

    Monitoring sensor alert The monitor panel turns red when a component value exceeds or is lower than the threshold value. Refer to the illustrations below. Small display Large display WMI browser Click to display the WMI (Windows Management Instrumentation) browser. This browser displays various Windows ®...
  • Page 51 The left panel of the tab lists all logical drives. Click a hard disk drive to display the information on the right panel. The pie chart at the bottom of the window represents the used (blue) and the available HDD space. ASUS Vintage2-PH1 3-13...

  • Page 52: Configuring Pc Probe Ii

    Memory usage The Memory tab shows both used and available physical memory. The pie chart at the bottom of the window represents the used (blue) and the available physical memory. Configuring PC Probe II Click to view and adjust the sensor threshold values. The Config window has two tabs: Sensor/Threshold and Preference.
  • Page 53 Chapter 4 This chapter gives information about the motherboard that comes with the system. This chapter includes the motherboard layout, jumper settings, and connector locations. ASUS Vintage2-PH1...

  • Page 54: Chapter 4: Motherboard Info

    Introduction The Vintage2-PH1 barebone system comes with an ASUS motherboard. This chapter provides technical information about the motherboard for future upgrades or system reconfiguration. Motherboard layout CPU_FAN PS/2KBMS T: Mouse B: Keyboard COM1 ATX12V LGA775 Bottom: COM2 Top: USB1 1394...

  • Page 55: Jumpers

    Hold down the <Del> key during the boot process and enter BIOS setup to re-enter data. CLRTC Normal Clear CMOS Clear RTC RAM (Default) Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default position. Removing the cap will cause system boot failure. ASUS Vintage2-PH1...

  • Page 56: Connectors

    Connectors Floppy disk drive connector (34-1 pin FLOPPY) This connector is for the provided floppy disk drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. Pin 5 on the connector is removed to prevent incorrect cable connection when using a FDD cable with a covered Pin 5.

  • Page 57: Serial Ata Connectors

    Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! Do not place jumper caps on the fan connectors! CPU_FAN CPU FAN PWM CPU FAN IN CPU FAN PWR PWR_FAN +12V Rotation CHA_FAN +12V Rotation Fan connectors ASUS Vintage2-PH1...
  • Page 58 USB connectors (10-1 pin USB56, USB78) These connectors are for USB 2.0 ports. Connect the USB/GAME module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specification that supports up to 480 Mbps connection speed.
  • Page 59 HD Audio or legacy ACʼ97 audio standard. AAFP Azalia Legacy AC’97 compliant definition compliant definition Analog front panel connector It is recommended that you connect a high-definition front panel audio module to this connector to avail of the motherboardʼs high-definition audio capability. ASUS Vintage2-PH1...

  • Page 60: Ieee 1394 Connector

    Digital audio connector (4-1 pin SPDIF_OUT) This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port(s). Connect the S/PDIF module cable to this connector, then install the module to a slot opening at the back of the system chassis. The S/PDIF module is purchased separately.
  • Page 61 12. Power LED connector (3-pin PLED) This 3-pin connector is for the system power LED. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode. PLED PLED- PLED+ Power LED connector ASUS Vintage2-PH1...
  • Page 62 13. Speaker connector (4-pin SPEAKER) This 4-pin connector is for the chassis-mounted system warning speaker. The speaker allows you to hear system beeps and warnings. SPEAKER Speak Out Speaker out connector 14. System front panel connector (10-1 pin F_PANEL) This connector supports several front panel chassis-mounted functions.
  • Page 63 Hard disk drive activity (Red 2-pin IDELED) This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED cable to this connector. The IDE LED lights up or flashes when data is read from or written to the HDD. ASUS Vintage2-PH1 4-11...
  • Page 64 4-12 Chapter 4: Motherboard info...
  • Page 65 Chapter 5 This chapter tells how to change system settings through the BIOS Setup menus and describes the BIOS parameters. ASUS Vintage2-PH1...

  • Page 66: Managing And Updating Your Bios

    ASUS AFUDOS (Updates the BIOS in DOS mode using a bootable floppy disk.) ASUS EZ Flash (Updates the BIOS using a floppy disk during POST.) ASUS CrashFree BIOS 2 (Updates the BIOS using a bootable floppy disk or the motherboard support CD when the BIOS file fails or gets corrupted.)

  • Page 67: Asus Ez Flash Utility

    5.1.2 ASUS EZ Flash utility The ASUS EZ Flash feature allows you to update the BIOS without having to go through the long process of booting from a floppy disk and using a DOS-based utility. The EZ Flash utility is built-in the BIOS chip so it is accessible by pressing <Alt>...

  • Page 68: Afudos Utility

    5.1.3 AFUDOS utility The AFUDOS utility allows you to update the BIOS file in DOS environment using a bootable floppy disk with the updated BIOS file. This utility also allows you to copy the current BIOS file that you can use as backup when the BIOS fails or gets corrupted during the updating process.

  • Page 69: Updating The Bios File

    Updating the BIOS file To update the BIOS file using the AFUDOS utility: Visit the ASUS website (www.asus.com) and download the latest BIOS file for the motherboard. Save the BIOS file to a bootable floppy disk. Write the BIOS filename on a piece of paper. You need to type the exact BIOS filename at the DOS prompt.

  • Page 70: Asus Crashfree Bios 2 Utility

    5.1.4 ASUS CrashFree BIOS 2 utility The ASUS CrashFree BIOS 2 is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process. You can update a corrupted BIOS file using the motherboard support CD or the floppy disk that contains the updated BIOS file.

  • Page 71: Recovering The Bios From The Support Cd

    BIOS file. The utility then updates the corrupted BIOS file. Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Floppy not found! Checking for CD-ROM... CD-ROM found! Reading file “P5LD2MQ.ROM”. Completed. Start flashing... ASUS Vintage2-PH1...

  • Page 72: Asus Update Utility

    Visit the ASUS website (www.asus.com) to download the latest BIOS file. 5.1.5 ASUS Update utility The ASUS Update is a utility that allows you to manage, save, and update the motherboard BIOS in Windows environment. The ASUS Update utility ®...

  • Page 73: Updating The Bios Through The Internet

    To update the BIOS through the Internet: Launch the ASUS Update utility from the Windows desktop by clicking ® Start > Programs > ASUS > ASUSUpdate > ASUSUpdate. The ASUS Update main window appears. Select Update BIOS from Select the ASUS FTP site...

  • Page 74: Updating The Bios Through A Bios File

    To update the BIOS through a BIOS file: Launch the ASUS Update utility from the Windows desktop ® by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate. The ASUS Update main window appears. Select Update BIOS from a file option from the drop-down menu, then click Next.

  • Page 75: Bios Setup Program

    The BIOS setup screens shown in this section are for reference purposes only, and may not exactly match what you see on your screen. • Visit the ASUS website (www.asus.com) to download the latest BIOS file for this motherboard and . ASUS Vintage2-PH1 5-11...

  • Page 76: Bios Menu Screen

    5.2.1 BIOS menu screen Menu items Menu bar Configuration fields General help Use [ENTER], [TAB] System Time [11:51:19] or [SHIFT-TAB] to System Date [Thu 05/07/2004] select a field. Legacy Diskette A [1.44M, 3.5 in] Use [+] or [-] to Primary IDE Master : [ST320413A] configure system time.

  • Page 77: Menu Items

    [English] For example, selecting Main shows the Use [+] or [-] to Primary IDE Master :[ST320413A] configure system time. Primary IDE Slave :[ASUS CD-S340] Secondary IDE Master :[Not Detected] Main menu items. Secondary IDE Slave :[Not Detected] Third IDE Master...

  • Page 78: Main Menu

    Main menu When you enter the BIOS Setup program, the Main menu screen appears, giving you an overview of the basic system information. Refer to section “5.2.1 BIOS menu screen” for information on the menu screen items and how to navigate through them. Use [ENTER], [TAB] System Time [11:51:19]...

  • Page 79: Primary, Third And Fourth Ide Master/Slave

    When set to [Disabled], the data transfer from and to the device occurs one sector at a time. Configuration options: [Disabled] [Auto] ASUS Vintage2-PH1 5-15...

  • Page 80: Ide Configuration

    PIO Mode [Auto] Selects the PIO mode. Configuration options: [Auto] [0] [1] [2] [3] [4] DMA Mode [Auto] Selects the DMA mode. Configuration options: [Auto] [SWDMA0] [SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5] SMART Monitoring [Auto] Sets the Smart Monitoring, Analysis, and Reporting Technology.
  • Page 81 If you set to any of these options and encounter problems, revert to the default setting S-ATA. Configuration options: [P-ATA+S-ATA] [S-ATA] [P-ATA] IDE Detect Time Out [35] Selects the time out value for detecting ATA/ATAPI devices. Configuration options: [0] [5] [10] [15] [20] [25] [30] [35] ASUS Vintage2-PH1 5-17...

  • Page 82: System Information

    5.3.6 System Information This menu gives you an overview of the general system specifications. The BIOS automatically detects the items in this menu. AMIBIOS Version : 0112 Build Date : 11/18/05 Processor Type : Genuine Intel(R) CPU 3.20GHz Speed : 3800 MHz Count System Memory Size...

  • Page 83: Advanced Menu

    Manual - allows you to individually set overclocking parameters. Auto - loads the optimal settings for the system. Standard - loads the standard settings for the system. Overclock Profile - loads overclocking profiles with optimal parameters for stability when overclocking. ASUS Vintage2-PH1 5-19...
  • Page 84 The following item appears only when you set the AI Overclocking item to [Manual]. CPU Frequency [XXX] Displays the frequency sent by the clock generator to the system bus and PCI bus. The value of this item is auto-detected by the BIOS. Use the <+> and <->...
  • Page 85 The following item appears only when the AI Overclocking item is set to [Overclock Profile]. Overclock Options [Overclock 5%] Allows you to overclock the CPU speed through the available preset values. Configuration options: [Overclock 5%] [Overclock 10%] [Overclock 15%] [Overclock 20%] [Overclock 30%] ASUS Vintage2-PH1 5-21...

  • Page 86: Usb Configuration

    5.4.2 USB Configuration The items in this menu allows you to change the USB-related features. Select an item then press <Enter> to display the configuration options. USB Configuration Module Version - 2.23.0-F.4 USB Devices Enabled: None USB Function [Enabled] Legacy USB Support [Auto] USB 2.0 Controller [Enabled]...

  • Page 87: Cpu Configuration

    Configuration options: [Disabled] [Enabled] Enhanced C1 Control [Auto] When set to [Auto], the BIOS will automatically check the CPUʼs capability to enable the C1E support. In C1E mode, the CPU power consumption is lower when idle. Configuration options: [Auto] [Disabled] ASUS Vintage2-PH1 5-23...
  • Page 88 CPU Internal Thermal Control [Auto] Disables or sets the CPU internal thermal control. Configuration options: [Disabled] [Auto] Hyper-Threading Technology [Enabled] Allows you to enable or disable the processor Hyper-Threading Technology. Configuration options: [Disabled] [Enabled] The following item appears only when you installed an Intel Pentium ®...

  • Page 89: Chipset

    Sets the RAS Activate timing to Precharge timing. Configuration options: [4 Clocks] [5 Clocks] ~ [18 Clocks] DRAM Write Recovery Time [4 Clocks] Sets the DRAM Write Recover Time. Configuration options: [2 Clocks] [3 Clocks] [4 Clocks] [5 Clocks] [6 Clocks] ASUS Vintage2-PH1 5-25...

  • Page 90: Onboard Devices Configuration

    Graphic Adapter Priority [PCI Express/Int-VGA] Allows selection of the graphics controller to use as primary boot device. Configuration options: [Internal VGA] [PCI Express/Int-VGA] [PCI Express/PCI] [PCI/PCI Express] [PCI/Int-VGA] Internal Graphics Mode Select [Enabled, 8MB] Sets the internal graphics mode. Configuration options: [Disabled] [Enabled, 1MB] [Enabled, 8MB] Graphics memory type [Auto] Sets the graphics memory type.
  • Page 91 Allows selection of the Parallel Port EPP version. This item appears only when the Parallel Port Mode is set to EPP. Configuration options: [1.9] [1.7] Parallel Port IRQ [IRQ7] Sets the parallel port IRQ. Configuration options: [IRQ5] [IRQ7] ASUS Vintage2-PH1 5-27...

  • Page 92: Pci Pnp

    5.4.6 PCI PnP The PCI PnP menu items allow you to change the advanced settings for PCI/PnP devices. The menu includes setting IRQ and DMA channel resources for either PCI/PnP or legacy ISA devices, and setting the memory size block for legacy ISA devices.

  • Page 93: Power Menu

    Allows you to enable or disable the Advanced Configuration and Power Interface (ACPI) support in the Application-Specific Integrated Circuit (ASIC). When set to Enabled, the ACPI APIC table pointer is included in the RSDT pointer list. Configuration options: [Disabled] [Enabled] ASUS Vintage2-PH1 5-29...

  • Page 94: Apm Configuration

    5.5.4 APM Configuration APM Configuration Enabled or disable APM. Power Button Mode [On/Off] Restore on AC Power Loss [Power Off] Power On By RTC Alarm [Disabled] Power On By External Modems [Disabled] Power On By PCI Devices [Disabled] Power On By PCIE Devices [Disabled] Select Screen Select Item...
  • Page 95 When set to [Enabled], this parameter allows you to turn on the system through a PCI Express LAN card. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled] [Enabled] ASUS Vintage2-PH1 5-31...

  • Page 96: Hardware Monitor

    field shows N/A. Configuration options: [Ignored] [xxxRPM] CPU Q-Fan Control [Disabled] Allows you to enable or disable the ASUS Q-Fan feature that smartly adjusts the fan speeds for more efficient system operation. Configuration options: [Disabled] [Enabled] Chassis Fan Speed [xxxxRPM] or [N/A] The onboard hardware monitor automatically detects and displays the chassis fan speed in rotations per minute (RPM).
  • Page 97 field shows N/A. Configuration options: [Ignored] [xxxRPM] or [N/A] VCORE Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage The onboard hardware monitor automatically detects the voltage output through the onboard voltage regulators. ASUS Vintage2-PH1 5-33...

  • Page 98: Boot Menu

    1st Boot Device [1st FLOPPY DRIVE] 2nd Boot Device [PM-ST330620A] 3rd Boot Device [PS-ASUS CD-S360] 1st ~ xxth Boot Device [1st Floppy Drive] Select Screen Select Item These items specify the boot device priority sequence from the available Enter Go to Sub-screen General Help devices.

  • Page 99: Boot Settings Configuration

    This allows you to enable or disable the full screen logo display feature. Configuration options: [Disabled] [Enabled] Set this item to [Enabled] to use the ASUS MyLogo2™ feature. Add On ROM Display Mode [Force BIOS] Sets the display mode for option ROM.

  • Page 100: Security

    Interrupt 19 Capture [Disabled] When set to [Enabled], this function allows the option ROMs to trap Interrupt 19. Configuration options: [Disabled] [Enabled] 5.6.3 Security The Security menu items allow you to change the system security settings. Select an item then press <Enter> to display the configuration options. Security Settings <Enter>...

  • Page 101: Change User Password

    The message “Password Installed” appears after you set your password successfully. To change the user password, follow the same steps as in setting a user password. Clear User Password Select this item to clear the user password. ASUS Vintage2-PH1 5-37...

  • Page 102: Exit Menu

    Password Check [Setup] When set to [Setup], BIOS checks for user password when accessing the Setup utility. When set to [Always], BIOS checks for user password both when accessing Setup and booting the system. Configuration options: [Setup] [Always] Exit menu The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items.

  • Page 103: Discard Changes

    Setup menus. When you select this option or if you press <F5>, a confirmation window appears. Select Ok to load default values. Select Exit & Save Changes or make other changes before saving the values to the non-volatile RAM. ASUS Vintage2-PH1 5-39...
  • Page 104 5-40 Chapter 5: BIOS setup...

This manual is also suitable for:

Vintage2-ph1

Table of Contents