Advertisement
Quick Links
Installation and Assembly:
Universal Articulating Wall Mount for 20" - 42" Screens
Model: MT80 ARM20
Features:
• Universal design for 20" - 42" flat panel screens
• Three tensionable pivot points for extensive adjustment of viewing angle
®
• VESA
100/200/200 x 200 compatible
• Frees up space by folding flat against the wall
R
• Keeps electronic wires routed internal to reduce clutter
Max UL Load Capacity: 80 lb (36.3 kg)
Visit the Westinghouse Web Site at www.westinghousedigital.com
For customer care call 1-866-287-5555.
ISSUED: 01-17-06 SHEET #: 202-9094-1
Advertisement
Related Manuals for Westinghouse MT80 ARM20
Summary of Contents for Westinghouse MT80 ARM20
- Page 1 • Frees up space by folding flat against the wall • Keeps electronic wires routed internal to reduce clutter Max UL Load Capacity: 80 lb (36.3 kg) Visit the Westinghouse Web Site at www.westinghousedigital.com For customer care call 1-866-287-5555. ISSUED: 01-17-06 SHEET #: 202-9094-1...
- Page 2 Note: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Westinghouse product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, call customer service at 1-866-287-5555.
-
Page 3: Parts List
Parts List Description Qty. Part # A wall mount 095-0345 B Alligator® anchor 590-0097 C .198" ID x .313" OD x .437" H retaining spacer 590-5003 D 3/16" allen wrench 560-9713 E M4 x .7 x 12 mm phillips screw 504-2013 F M4 x .7 x 20 mm phillips screw 504-2014... -
Page 4: Installation To Wood Stud Wall
Installation to Wood Stud Wall WARNING • Make sure that the wall will safely support the combined load of the equipment and all attached hardware and components. Remove cord covers from wall arm assembly (A) as shown in figure 1.1. Using a stud finder, locate and mark the edges of the wood stud used in mounting this product. -
Page 5: Installation To Solid Concrete And Cinder Block
WARNING • When installing Westinghouse wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual con- crete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1"... - Page 6 2.3, and attach adapter plate to screen accordingly. Verify that all holes are properly aligned, and then tighten screws using security allen wrench (D). For additional screen compatibility please refer to the Westinghouse Décor wall mount list on out website at www.westinghousedigital.com.
- Page 7 FOR VESA 100 MOUNTING PATTERN: Thread two M4 x 12 mm screws (E), leaving .25" exposed thread, into top holes on back of screen. Hook screen onto adapter plate, and attach using bottom two M4 x 12 mm screws as shown in figures 2.4 and 2.5. Tighten all four screws. *Note: If screw (E) gets less than three threads of engagement, attach adapter plate to back of screen using four M4 x 20 mm screws (F) as indicated in figure 2.5.
- Page 8 Adjust tension knob on side of mount shown in figure 3 to desired tension to balance your screen size and weight. Push or pull from top or bottom of screen to adjust tilt as shown. The tilt can be adjusted to a maximum of 15°...
- Page 9 WARNING • Do not remove screw or loosen screw until it is no longer engaged with the mount. Doing so may cause the screen to fall. If more or less tension is desired in the arm pivot points, do the following: •...
- Page 10 REPAIR OR REPLACEMENT – For a period of five (5) years from the original date of purchase, Westinghouse Digital Electronics will repair any defect in material or workmanship in the Product, or, at its option, replace a defective Product.