Information; Specifications; In Case Of Difficulty - Alpine HCE-C300R Owner's Manual

Information

Specifications

e
Camera section
Image sensor . . . . . . . . . . . . . . 1/4 Type Colour CMOS
Effective Number of Pixels . . 640 (horizontal) × 480
Lens Section . . . . . . . . . . . . . . . Focal length f = 0.8 mm,
Angle of Field . . . . . . . . . . . . . . Horizontal: 190 °,
Automatic Image Adjusting
Function . . . . . . . . . . . . . . . . . . . Automatic metering
Synchro-System. . . . . . . . . . . . Internal synchronization
Resolution (Horizontal) . . . . . 250 lines (centre area)
Illumination Range . . . . . . . . . 2 to 100,000 lx
Operating Temperature
Range . . . . . . . . . . . . . . . . . . . . . -22 to +158 °F
Storage Temperature
Range . . . . . . . . . . . . . . . . . . . . . -40 to +185 °F
External Dimensions . . . . . . .
(W × D × H)
Weight . . . . . . . . . . . . . . . . . . . . 30 g (including cable)
e
Control unit section
Power Requirements . . . . . . . 14.4 V DC
Ground Type . . . . . . . . . . . . . . . Negative ground type
Output Image . . . . . . . . . . . . . . Mirror image, CVBS
Output Drive Capacity . . . . . 75 ohm (W)
Operating Temperature
Range . . . . . . . . . . . . . . . . . . . . . -4 to +140 °F
External Dimensions . . . . . . .
(W × D × H)
Weight . . . . . . . . . . . . . . . . . . . . 450 g (including cable)
Image sensor, aspect
ratio 4 : 3
(vertical) approximately
0.3 Megapixels
brightness F = 2.6
Vertical: 155 °
(Control unit output:
180 °)
adjustment, Automatic
white balance
adjustment
(-30 to +70 °C)
(-40 to +85 °C)
21 × 21 × 23.8mm
(53/64" × 53/64" ×
15/16") (excluding cable)
(11 to 16 V allowable)
(NTSC Colour signal
system)
(-20 to +60 °C)
176 × 110 × 30 mm
(6-15/16" × 4-5/16" ×
1-3/16")

In Case of Difficulty

•
The camera image does not appear. (Images
other than that of the camera are normal.)
Cause
The ignition key is Set the ignition key to ON.
set to a position other
than ON.
No fuse is installed, or Install a fuse, or replace a
there is a break in the relevant fuse after checking
connection. the cause.
The connection is not Check whether the connection
correctly established. is correctly established while
referring to this owner's
manual.
The reverse signal Connect the reverse signal line
line of the connected while referring to the owner's
product is not manual of the connected
connected. product.
The video connection Connect the video connection
cable is not connected cable to the camera input
to the camera input while referring to the owner's
of the connected manual of the connected
product. product.
The rear camera The control unit SETUP
image does not switch might be ON.
display, and the Turn the ignition key to OFF
calibration mode and then set the SETUP switch
appears. to OFF. Wait for approximately
1 minute and then turn the
ignition key to ON again.
•
The camera image is not normal. (Images other
than that of the camera are normal.)
Symptom
The display screen If a place illuminated by a
flickers. fluorescent lamp is captured,
the display screen may flicker.
This is not a failure.
The screen is difficult If a dark place or a partially
to read. bright light is captured, or if
the temperature of the main
body of the camera is high, the
screen may be difficult to read.
This is not a malfunction.
The camera image Check the installation
sways. status, and check screws for
looseness.
The camera image is If the camera lens is dirty, wipe
unclear. the lens softly with a soft cloth
moistened with water.
Solution
Cause/Solution
35
-EN