FUNAI LT850-M22 Service Manual
  1. Manuals
  2. Brands
  3. FUNAI Manuals
  4. LCD TV
  5. LT850-M22 - SERVICE
  6. Service manual

FUNAI LT850-M22 Service Manual

22″ color lcd television
Hide thumbs Also See for LT850-M22:
Table of Contents

Advertisement

Quick Links

Download this manual

SERVICE MANUAL

This Service Manual is for the
LT850-M22 (A0C70EP) / LT851-M22 (A0C71EP) model.
For the LT850-M22 (A0C70EP) / LT851-M22 (A0C71EP) model, the letter
(A0C70EP) / (A0C71EP) is printed on the Serial Number Label on the back
of the unit. Refer to the Serial Number Label below.
Serial No. Label
Serial No. Label
"A0C70EP"
"A0C71EP"
22" COLOR LCD TELEVISION
LT850-M22 / LT851-M22

Advertisement

Table of Contents
loading

Related Manuals for FUNAI LT850-M22

Summary of Contents for FUNAI LT850-M22

  • Page 1: Service Manual

    SERVICE MANUAL This Service Manual is for the LT850-M22 (A0C70EP) / LT851-M22 (A0C71EP) model. For the LT850-M22 (A0C70EP) / LT851-M22 (A0C71EP) model, the letter (A0C70EP) / (A0C71EP) is printed on the Serial Number Label on the back of the unit. Refer to the Serial Number Label below. Serial No.

  • Page 2: Table Of Contents

    22″ COLOR LCD TELEVISION LT850-M22 / LT851-M22 TABLE OF CONTENTS Specifications ................1-1 Important Safety Precautions.

  • Page 3: Specifications

    SPECIFICATIONS < TUNER > VHS/UHF Input ----------- 75Ω unbal., IEC Connector Center IF ------------------- SECAM-L 38.9MHz, SECAM-L’ 33.9MHz Description Condition Unit Nominal Limit 1. Video S/N 2. Audio S/N 40/40 < LCD PANEL > Description Condition Unit Nominal Limit Horizontal pixels 1366 1.

  • Page 4: Specifications

    < AUDIO > All items are measured across 16 Ω load at speaker output terminal. Description Condition Unit Nominal Limit 1. Audio Output Power 10% THD: Lch/Rch 3.0/3.0 2.0/2.0 2. Audio Distortion 500mW: Lch/Rch 1.5/1.5 3.0/3.0 -6dB: Lch 70 to 10 k 3.

  • Page 5: Important Safety Precautions

    IMPORTANT SAFETY PRECAUTIONS Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
  • Page 6 4. Hot Chassis Warning - 7. Product Safety Notice - Some electrical and mechanical parts have special safety-related a. Some TV receiver chassis are electrically characteristics which are often not evident from connected directly to one conductor of the AC visual inspection, nor can the protection they give power cord and maybe safety-serviced without necessarily be obtained by replacing them with...
  • Page 7 Precautions during Servicing A. Parts identified by the ! symbol are critical for safety. Replace only with part number specified. B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements.
  • Page 8 Safety Check after Servicing Examine the area surrounding the repaired location Chassis or Secondary Conductor for damage or deterioration. Observe that screws, parts and wires have been returned to original posi- tions. Afterwards, perform the following tests and con- Primary Circuit firm the specified values in order to verify compliance with safety standards.

  • Page 9: Standard Notes For Servicing

    STANDARD NOTES FOR SERVICING Circuit Board Indications How to Remove / Install Flat Pack-IC 1. The output pin of the 3 pin Regulator ICs is 1. Removal indicated as shown. With Hot-Air Flat Pack-IC Desoldering Machine: 1. Prepare the hot-air flat pack-IC desoldering Top View Bottom View machine, then apply hot air to the Flat Pack-IC...
  • Page 10 With Soldering Iron: With Iron Wire: 1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, flux which is applied to all pins of the flat pack-IC, you can remove it easily.
  • Page 11 2. Installation Instructions for Handling Semi- 1. Using desoldering braid, remove the solder from conductors the foil of each pin of the flat pack-IC on the CBA Electrostatic breakdown of the semi-conductors may so you can install a replacement flat pack-IC more occur due to a potential difference caused by easily.

  • Page 12: Cabinet Disassembly Instructions

    CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart Removal Step/ Remove/*Unhook/ This flowchart indicates the disassembly steps for the Loc. Part Fig. Unlock/Release/ cabinet parts, and the CBA in order to gain access to Note Unplug/Unclamp/ item(s) to be serviced. When reassembling, follow the Desolder steps in reverse order.
  • Page 13 (S-2) (S-2) (S-4) (S-5) (S-2) (S-2) [2] Rear Cabinet (S-3) (S-2) [1] Stand Assembly (S-1) Fig. D1 A0C72_73DC...
  • Page 14 [14] Front Cabinet [9] Digital Main CBA Unit [7] Jack (S-13) [8] Shield Holder [12] Junction (S-11) (S-13) (S-10) [11] Speaker (H-1) Speaker Holder (S-12) (S-16) (S-17) (S-8) [13] Function CBA [11] Speaker (S-16) (S-9) [6] Jack CBA [5] HP Jack Speaker Holder Holder...
  • Page 15 TV Cable Wiring Diagram To LCD Module Assembly Digital Main CBA Unit Main CBA CN3901 CN301 CN1550 CN402 CN3701 CN403 CN3703 CN1650 CN404 CN3702 CN401 CN3704 CN1750 CN103 CN801 CN102A AC CORD Jack CBA CN802 CN452 To Speaker To Speaker Junction CBA CN102B CN101A...

  • Page 16: Electrical Adjustment Instructions

    ELECTRICAL ADJUSTMENT INSTRUCTIONS General Note: “CBA” is abbreviation for How to set up the service mode: “Circuit Board Assembly.” Service mode: Note: Electrical adjustments are required after 1. Turn the power on. replacing circuit components and certain mechanical parts. It is important to perform 2.

  • Page 17: Vcom Adjustment

    1. Purity Check Mode 2. VCOM Adjustment This mode cycles through full-screen displays of red, Test Point Adj. Point green, blue, and white to check for non-active pixels. 1. Enter the Service mode. Screen buttons 2. Each time pressing [7] button on the remote M.

  • Page 18: White Balance Adjustment

    The White Balance Adjustment should be 5. [CUTOFF] Press [1] button to select “COR” for Red Cutoff performed when replacing the LCD Panel adjustment. Press [3] button to select “COB” for or Digital Main CBA. Blue Cutoff adjustment. [DRIVE] 3. White Balance Adjustment Press [4] button to select “DR”...

  • Page 19: How To Initialize The Lcd Television

    HOW TO INITIALIZE THE LCD TELEVISION How to initialize the LCD television: 1. Turn the power on. 2. Enter the service mode. (Refer to page 5-1.) - To cancel the service mode, press [ ] button on the remote control unit. 3.

  • Page 20: Firmware Renewal Mode

    FIRMWARE RENEWAL MODE Equipment Required [Update procedure] 1. Plug in the AC power cord. a. USB storage device 2. Press [ ] button on the remote control unit to turn b. Remote Control Unit off (standby). 3. Check “STAND BY” indicator (Red LED) lighting. Firmware Update Procedure 4.

  • Page 21: Troubleshooting

    TROUBLESHOOTING FLOW CHART NO.1 The power cannot be turned on. See FLOW CHART No.2 <The fuse blows out.> Is the fuse (F601) normal? Check if there is any leak or short-circuiting on the primary circuit component, and service it if defective. (IC605, Q601, Q602, D602, D604, D605, D607, T601, R602) Is approximately 32V voltage supplied to the cathode...
  • Page 22 FLOW CHART NO.5 AL+3.3V is not output. Is approximately 5V voltage supplied to the collector Check D637, C628 and their periphery circuit, and of Q605? service it if defective. Is approximately 4V voltage supplied to the base Check D634 and their periphery circuit, and of Q605? service it if defective.
  • Page 23 FLOW CHART NO.9 PANEL+25.6V is not output. Is approximately 32V voltage supplied to the cathode of D618? Is approximately 32V voltage outputted to the collector of Q612? Check D617, D636 and their periphery circuit, and service it if defective. FLOW CHART NO.10 PANEL+12.5V is not output.
  • Page 24 FLOW CHART NO.12 AL+5V is not output. Check if there is any leak or short-circuit on the loaded circuit, and service it if defective. FLOW CHART NO.13 P-ON+3.3V is not output. Replace Q606. FLOW CHART NO.14 P-ON+11V is not output. Is approximately 12V voltage supplied to the base of Q609? Replace Q609.
  • Page 25 FLOW CHART NO.16 No operation is possible from the remote control unit. Check AL+3.3V line and service it if defective. Replace the RS101 (remote control receiver) or remote control unit. Check the line between Pin(1) of RS101 (remote control receiver) and Pin(13) of CN403, and service it if defective.
  • Page 26 FLOW CHART NO.18 Picture does not appear normally. Check the line between Pin(16, 18) of CN403 and Are the DIF signals outputted to Pin(16, 18) of CN403? Pin(4, 5) of TU10, and TU10(Tuner Unit), and service it if defective. Replace Digital Main CBA Unit or LCD Module Assembly.

  • Page 27: Block Diagrams

    BLOCK DIAGRAMS System Control Block Diagram A0C70BLS...
  • Page 28 Video Block Diagram A0C70BLV...
  • Page 29 Audio Block Diagram A0C70BLA...
  • Page 30 Digital Signal Process Block Diagram A0C70BLD...
  • Page 31 Inverter Block Diagram A0C70BLINV...
  • Page 32 Power Supply Block Diagram A0C70BLP...

  • Page 33: Schematic Diagrams / Cba And Test Points

    SCHEMATIC DIAGRAMS / CBA AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
  • Page 34 LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE. 2. CAUTION: Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply.
  • Page 35 Main 1 Schematic Diagram CAUTION ! NOTE: CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. The voltage for parts in hot circuit is measured using For continued protection against fire hazard, If Main Fuse (F601) is blown , check to see that all components in the power supply hot GND as a common terminal.
  • Page 36 Main 2 Schematic Diagram 10-4 A0C70SCM2...
  • Page 37 Main 3 Schematic Diagram 10-5 A0C70SCM3...
  • Page 38 Main 4 Schematic Diagram 10-6 A0C70SCM4...
  • Page 39 Function & Junction Schematic Diagram 10-7 A0C70SCF...
  • Page 40 Jack Schematic Diagram 10-8 A0C70SCJ...
  • Page 41 Digital Main 1 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into six and shown as IC3301 (1/7) ~ IC3301 (7/7) in this Digital Main Schematic Diagram Section. 10-9 A0C70SCD1...
  • Page 42 Digital Main 2 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into six and shown as IC3301 (1/7) ~ IC3301 (7/7) in this Digital Main Schematic Diagram Section. 10-10 A0C70SCD2...
  • Page 43 Digital Main 3 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into six and shown as IC3301 (1/7) ~ IC3301 (7/7) in this Digital Main Schematic Diagram Section. 10-11 A0C70SCD3...
  • Page 44 Digital Main 4 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into six and shown as IC3301 (1/7) ~ IC3301 (7/7) in this Digital Main Schematic Diagram Section. 10-12 A0C70SCD4...
  • Page 45 Digital Main 5 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into six and shown as IC3301 (1/7) ~ IC3301 (7/7) in this Digital Main Schematic Diagram Section. 10-13 A0C70SCD5...
  • Page 46 Digital Main 6 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into six and shown as IC3301 (1/7) ~ IC3301 (7/7) in this Digital Main Schematic Diagram Section. 10-14 A0C70SCD6...
  • Page 47 Digital Main 7 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into six and shown as IC3301 (1/7) ~ IC3301 (7/7) in this Digital Main Schematic Diagram Section. 10-15 A0C70SCD7...
  • Page 48 Main CBA Top View Because a hot chassis ground is present in the power supply NOTE: CAUTION ! circuit, an isolation transformer must be used when repairing. The voltage for parts in hot circuit is measured using Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. Also, in order to have the ability to increase the input slowly, hot GND as a common terminal.
  • Page 49 Main CBA Bottom View Because a hot chassis ground is present in the power supply NOTE: CAUTION ! circuit, an isolation transformer must be used when repairing. The voltage for parts in hot circuit is measured using Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. Also, in order to have the ability to increase the input slowly, hot GND as a common terminal.
  • Page 50 Jack CBA, Function CBA & Junction CBA Top View Function CBA Junction CBA Jack CBA 10-18 BA0C70F01021...
  • Page 51 Jack CBA, Function CBA & Junction CBA Bottom View Junction CBA Function CBA Jack CBA 10-19 BA0C70F01021...

  • Page 52: Waveforms

    WAVEFORMS WF1 ~ WF6 = Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram.) Input: PAL Color Bar Signal (with 1kHz Audio Signal) Pin 2 of CN404 Pin 4 of CN404 VIDEO-Y VIDEO-Y 0.2V 0.2V 20µs 20µs VIDEO VIDEO 0.2V...
  • Page 53 WF7 ~ WF10 = Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram.) Input: PAL Color Bar Signal (with 1kHz Audio Signal) Pin 22 of CN401 Pin 26 of CN404 WF10 AUDIO(L) AUDIO(L) 0.5V 0.5V 0.5m 0.5ms VIDEO-R VIDEO-R 0.5V...

  • Page 54: Wiring Diagram

    WIRING DIAGRAMS A0C70WI 12-1...

  • Page 55: Exploded View

    EXPLODED VIEWS Cabinet Digital Main CBA Unit CL302 CL303 X3301 CL404 CL3901 CL401 CL301 Junction CBA SP802 CL103 Jack CBA CL802 SP801 Function CBA CL801 LCD1 See Electrical Parts List for parts with this mark. Main CBA AC601 Stand Assembly 13-1 A0C70_71CEX...
  • Page 56 Packing X2-1 Stand X2-2 Assembly Tape Tape Packing Tape Packing Tape Some Ref. Numbers are not in sequence. Packing Tape 13-2 A0C70_71PEX...

  • Page 57: Mechanical Parts List

    MECHANICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a Ref. No. Mark Description Part No. ! have special characteristics important to safety. SP802 SPEAKER S0307F03 DS08070XQ001 Before replacing any of these components, read X3301 THERMOSTAR TMS-L-2(12*12HC) XK10000X4003 carefully the product safety notice in this service PACKING manual.

  • Page 58: Electrical Parts List

    ELECTRICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a Ref. No. Mark Description Part No. ! have special characteristics important to safety. CAP CHIP 1608 J/C0G/0.001µF/50V CHD102EYA030 Before replacing any of these components, read C154 CHIP CERAMIC CAP .(1608) F Z 0.1µF/ CHD1EZ30F104 carefully the product safety notice in this service C155...
  • Page 59 Ref. No. Mark Description Part No. Ref. No. Mark Description Part No. C432 CHIP CERAMIC CAP .(1608) F Z 0.1µF/ CHD1EZ30F104 ELECTROLYTIC CAP 3300µF/10V or CE1AMZNDL332 CAP ELE 3300µF/10V/M/85 or CEB332KSN002 C433 CHIP CERAMIC CAP .(1608) B K 1µF/10V CHD1AK30B105 CAP ELE 3300µF/10V/M/85 CEB332TEP002 C616...
  • Page 60 Ref. No. Mark Description Part No. Ref. No. Mark Description Part No. C646 CHIP CERAMIC CAP .(1608) B K 0.1µF/ CHD1JK30B104 C1006 ELECTROLYTIC CAP . 10µF/50V M or CE1JMASDL100 50V or CAP ELE 10µF/50V/M/85 or CEF100KSN001 CAP CHIP 1608 K/X7R/0.1µF/50V CHD104EYA032 CAP ELE 10µF/50V/M/85 CEF100TEP001...
  • Page 61 Ref. No. Mark Description Part No. Ref. No. Mark Description Part No. CAP ELE 10µF/50V/M/85 CEF100TEP001 CONNECTOR PRINT MES 29 S 1.0-11- JC1129JSH001 C1555 ELECTROLYTIC CAP . 10µF/50V M H7 or CE1JMAVSL100 CN403 FFC CONNECTOR IMSA-9615S-29A-PP- JC96J29ER007 CAP ELE 10µF/50V/M/85 H7 CEF100KSN003 A or C1558...
  • Page 62 Ref. No. Mark Description Part No. Ref. No. Mark Description Part No. DIODE SWITCHING HSS4148TE-E or QDTZ0HSS4148 D635 SWITCHING DIODE 1SS133(T-77) or QDTZ001SS133 DIODE SWITCHING 1N4148-F0021 NDTZ01N4148F DIODE SWITCHING HSS4148TE-E or QDTZ0HSS4148 D600 WIRE CP STP-S-0.50 or XZ40F0REN001 DIODE SWITCHING 1N4148-F0021 NDTZ01N4148F WIRE CP STP-S-0.60 or XZ40F0REN002...
  • Page 63 Ref. No. Mark Description Part No. Ref. No. Mark Description Part No. DIODE ZENER HZS15NB2TE-EQ QDTBHZS15NB2 DIODE SWITCHING 1N4148-F0021 NDTZ01N4148F D815 DIODE ZENER 8V2BSB-T26 or NDTB8R2BST26 D1562 SWITCHING DIODE 1SS133(T-77) or QDTZ001SS133 DIODE ZENER HZS8.2NB2TE-EQ QDTB0HZS8R2N DIODE SWITCHING HSS4148TE-E or QDTZ0HSS4148 D1003 WIRE CP STP-S-0.50 or...
  • Page 64 Ref. No. Mark Description Part No. Ref. No. Mark Description Part No. D1756 SWITCHING DIODE 1SS133(T-77) or QDTZ001SS133 TRANSISTOR 2SA1015-GR(TE2 F T) or QQS12SA1015F DIODE SWITCHING HSS4148TE-E or QDTZ0HSS4148 PNP TRANSISTOR 2SA1980Y-AT or NQSY02SA1980 DIODE SWITCHING 1N4148-F0021 NDTZ01N4148F PNP TRANSISTOR 2SA1980 G or NQSG02SA1980 D1757 SWITCHING DIODE 1SS133(T-77) or...
  • Page 65 Ref. No. Mark Description Part No. Ref. No. Mark Description Part No. Q610 TRANSISTOR KTA1267-GR-AT/P or NQS1KTA1267P PNP TRANSISTOR 2SA1980 G or NQSG02SA1980 TRANSISTOR KTA-1266-GR-AT/P or NQS4KTA1266P PNP TRANSISTOR 2SA1980M Y or NQSY2SA1980M TRANSISTOR 2SA1015-Y(TE2 F T) or QQSY2SA1015F PNP TRANSISTOR 2SA1980MG-AT NQSG2SA1980M TRANSISTOR 2SA1015-GR(TE2 F T) or QQS12SA1015F...
  • Page 66 Ref. No. Mark Description Part No. Ref. No. Mark Description Part No. TRANSISTOR 2SC2120-O(TE2 F T) or QQS02SC2120F NPN TRANSISTOR SMD 2SC5343UFL NQ1L2SC5343U TRANSISTOR KTC3203-Y-AT/P or NQSYKTC3203P Q1023 NPN TRANSISTOR SMD QQ1Q2SC4081U 2SC4081UBTLQ or TRANSISTOR KTC3203-O-AT/P or NQS0KTC3203P NPN TRANSISTOR SMD QQ1R2SC4081U NPN TRANSISTOR 2SC5344 Y or NQSY02SC5344...
  • Page 67 Ref. No. Mark Description Part No. Ref. No. Mark Description Part No. TRANSISTOR 2SA1015-GR(TE2 F T) or QQS12SA1015F WIRE CP 6113-05603-0220 or XZ40F0SHG001 PNP TRANSISTOR 2SA1980Y-AT or NQSY02SA1980 WIRE CP CP0.56 XZ40F0XRC001 CHIP RES. 1/10W J 10k Ω or PNP TRANSISTOR 2SA1980 G or NQSG02SA1980 R313 RRXAJR5Z0103...
  • Page 68 Ref. No. Mark Description Part No. Ref. No. Mark Description Part No. RES CARBON FILM T 1/4W J 15k Ω or RES CARBON FILM T 1/4W J 390 Ω or R453 RCX4153T1001 R610 RCX4391T1001 RES CARBON FILM 1/4W J 15k Ω or RES CARBON FILM 1/4W J 390 Ω...
  • Page 69 Ref. No. Mark Description Part No. Ref. No. Mark Description Part No. RES CARBON FILM 1/4W J 18 Ω RES CARBON FILM 1/4W J 10 Ω or RCJ180PAK001 RCX4100FS002 CHIP RES. 1/10W F 3.3k Ω or RES CARBON FILM 1/4W J 10 Ω R642 RRXAFR5H3301 RCJ100PAK001...
  • Page 70 Ref. No. Mark Description Part No. Ref. No. Mark Description Part No. CHIP RES. 1/10W J 12k Ω or RES CHIP 1608 1/10W J 1.0k Ω R808 RRXAJR5Z0123 RRXA102YF002 RES CHIP 1608 1/10W J 12k Ω CHIP RES. 1/10W J 1k Ω or RRXA123YF002 R1023 RRXAJR5Z0102...
  • Page 71 Ref. No. Mark Description Part No. Ref. No. Mark Description Part No. CHIP RES. 1/10W F 7.5k Ω or RES CHIP 1608 1/10W J 9.1k Ω RRXAFR5Z7501 RRXA912YF002 RES CHIP 1608 1/10W F 7.50k Ω CHIP RES. 1/10W J 220k Ω or RTW7501YF002 R1560 RRXAJR5Z0224...
  • Page 72 Ref. No. Mark Description Part No. Ref. No. Mark Description Part No. WIRE CP 6113-05603-0220 or XZ40F0SHG001 T1500! TRANS INVERTER HVT-179 or LTZ3PZ0XB012 WIRE CP CP0.56 XZ40F0XRC001 TRANS INVERTER TK.7610A.101 or LTZ3PZDAR008 BC601 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 T1600! TRANS INVERTER HVT-179 or LTZ3PZ0XB012 TRANS INVERTER TK.7610A.101 or LTZ3PZDAR008...
  • Page 73 Ref. No. Description Part No. Ref. No. Description Part No. WIRE CP CP0.56 XZ40F0XRC001 RESISTORS CHIP RES.(1608) 1/10W 0 Ω or R477 WIRE CP STP-S-0.50 or XZ40F0REN001 R102 RRXAZR5Z0000 RES CHIP 1608 1/10W J 0 Ω WIRE CP STP-S-0.60 or XZ40F0REN002 RRXA000YF002 CHIP RES.
  • Page 74 Ref. No. Description Part No. CN102B 242 SERIES CONNECTOR TUC-P06X-B1 WHT JCTUB06TG002 Ref. No. Description Part No. TUNER UNIT DTOS40AML201A UTNPSG0SM002 20100507 15-17 A0C70/71EL...
  • Page 75 LT850-M22/LT851-M22 A0C70EP/A0C71EP 2010-06-03...

This manual is also suitable for:

Lt851-m22

Table of Contents