Related Manuals for SMC Networks FS26
Summary of Contents for SMC Networks FS26
-
Page 1: Installation Guide
INSTALLATION GUIDE SMCFS26 EZ Switch 10/100 24-Port Fast Ethernet Switch with 2 Gigabit uplinks... - Page 3 EZ Switch 10/100 Installation Guide From SMC’s EZ line of low-cost workgroup LAN solutions 20 Mason May 2007 Irvine, CA 92618 Pub. # 150200062500A E052007-AP-R01 Phone: (949) 679-8000...
- Page 4 No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice.
-
Page 5: Limited Warranty
“Active” SMC product. A product is considered to be “Active” while it is listed on the current SMC price list. As new technologies emerge, older technologies become obsolete and SMC will, at its discretion, replace an older product in its product line with one that incorporates these newer technologies. - Page 6 WHICH MAY VARY FROM STATE TO STATE. NOTHING IN THIS WARRANTY SHALL BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS. * SMC will provide warranty service for one year following discontinuance from the active SMC price list. Under the limited lifetime warranty, internal and external power supplies, fans, and cables are covered by a standard one-year warranty from date of purchase.
-
Page 7: Emi Certification
EMI Certification FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. - Page 8 CE Mark Declaration of Conformance for EMI and Safety (EEC) This information technology equipment complies with the requirements of the Council Directive 89/336/EEC on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain voltage limits and the Amendment Directive 93/68/ EEC.
-
Page 9: Safety Compliance
Safety Compliance Please read the following safety information carefully before installing the switch: Power Cord Set U.S.A. and Canada The cord set must be UL-approved and CSA certified. The minimum specifications for the flexible cord are: - No. 18 AWG - not longer than 2 meters, or 16 AWG. - Type SV or SJ - 3-conductor The cord set must have a rated current capacity of at least 10 A... - Page 10 • L’appareil fonctionne à une tension extrêmement basse de sécurité qui est conforme à la norme IEC 60950. Ces conditions ne sont maintenues que si l’équipement auquel il est raccordé fonctionne dans les mêmes conditions. France et Pérou uniquement: Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos alimentations sont du type impédance à...
-
Page 11: Warnings And Cautionary Messages
• Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich sein. Die Stromversorgung des Geräts kann nur durch Herausziehen des Gerätenetzkabels aus der Netzsteckdose unterbrochen werden. • Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen (Sicherheitskleinstspannung) gemäß IEC 60950. Diese Bedingungen sind nur gegeben, wenn auch die an das Gerät angeschlossenen Geräte unter SELV-Bedingungen betrieben werden. - Page 12 Environmental Statement The manufacturer of this product endeavours to sustain an environmentally-friendly policy throughout the entire production process. This is achieved though the following means: • Adherence to national legislation and regulations on environmental production standards. • Conservation of operational resources. •...
-
Page 13: Table Of Contents
Contents Introduction Features and Benefits Front and Rear Panels Rear Panel Front Panel RJ-45 Ports 1000BASE-T Ports LED Status Indicators Installing the Switch Package Contents Selecting a Site Instructions Applications Rack Mounting Product Specifications Physical Characteristics Switching Criteria Troubleshooting Diagnosing Switch Indicators Power and Cooling Problems Installation Cables... - Page 14 Contents...
-
Page 15: Introduction
Introduction The SMC EZ Switch 10/100, SMCFS26, is a high-performance Fast Ethernet switch designed for delivering 100 Mbps connectivity to the desktop. It provides 24 full- duplex 100BASE-TX ports and two 1000BASE-T uplink ports that significantly improve network performance and boost throughput for high-bandwidth applications. -
Page 16: 1000Base-T Ports
Introduction 1000BASE-T Ports The two 1000BASE-T RJ-45 ports operate at 10 Mbps or 100 Mbps, half or full duplex, or at 1000 Mbps, full duplex. Because these ports support automatic MDI/MDI-X operation, you can use straight-through cables for all network connections to PCs or servers, or to other switches or hubs. -
Page 17: Installing The Switch
Installing the Switch Before installing the switch, verify that you have all the items listed under “Package Contents.” If any of the items are missing or damaged, contact your local distributor. Also be sure you have all the necessary tools and cabling before installing the switch. -
Page 18: Applications
Installing the Switch Connecting PCs: Connect each PC to an RJ-45 port on the switch using Category 5, 5e, or 6 shielded or unshielded twisted-pair (UTP or STP) cable, maximum length 100 meters (328 ft). The switch will support up to 26 PCs. Note: If an attached device does not support auto-negotiation, the data rate will be sensed automatically and the communication mode will default to half duplex. -
Page 19: Rack Mounting
Installing the Switch 10 Mbps 1000 Mbps 100 Mbps 100 Mbps 10 Mbps Workstations 100 Mbps Workstation 1000 Mbps Server 100 Mbps Workstation Standalone LAN 100 Mbps 100 Mbps Workstations Servers 100 Mbps Workstation 10 Mbps 100 Mbps 100 Mbps Segment Segment 100 Mbps... - Page 20 Installing the Switch • Grounding: Rack-mounted equipment should be properly grounded. Particular attention should be given to supply connections other than direct connections to the mains. To rack-mount devices: Attach the brackets to the device using the screws provided in the Bracket Mounting Kit.
-
Page 21: Product Specifications
Product Specifications Physical Characteristics Standards Conformance IEEE Std 802.3-2005 Communication Rate Ports 1-24: 10 and 100 Mbps Ports 25-26: 10, 100, and 1000 Mbps Communication Mode Full or half duplex Media Supported 10BASE-T: 100-ohm Category 3 or better twisted-pair 100BASE-TX: 100-ohm Category 5 or better twisted pair 1000BASE-T: 100-ohm Category 5, 5e, or 6 twisted-pair Number of Ports 24 RJ-45 100BASE-TX ports... -
Page 22: Troubleshooting
Troubleshooting Diagnosing Switch Indicators Troubleshooting Chart Symptom Action Power LED is Off • Check connections between the switch, the power cord and the wall outlet. • Check the power outlet by using it for another device. • Contact your dealer for assistance. Link LED is Off •... -
Page 23: Cables
Cables Twisted-Pair cable and Pin Assignments For 10/100BASE-TX connections, the twisted-pair cable must have two pairs of wires. For 1000BASE-T connections the twisted-pair cable must have four pairs of wires. Each wire pair is identified by two different colors. For example, one wire might be green and the other, green with white stripes. -
Page 24: Straight-Through Wiring
Cables 10/100BASE-TX MDI and MDI-X Port Pinouts MDI Signal Name MDI-X Signal Name Receive Data plus (RD+) Transmit Data plus (TD+) Receive Data minus (RD-) Transmit Data minus (TD-) Transmit Data plus (TD+) Receive Data plus (RD+) Transmit Data minus (TD-) Receive Data minus (RD-) Not used Not used... -
Page 25: 1000Base-T Pin Assignments
Cables EIA/TIA 568B RJ-45 Wiring Standard 10/100BASE-TX Crossover Cable White/Orange Stripe Orange White/Green Stripe End A End B Blue White/Blue Stripe Green White/Brown Stripe Brown Crossover Wiring 1000BASE-T Pin Assignments All 1000BASE-T ports support automatic MDI/MDI-X operation, so you can use straight-through cables for all network connections to PCs or servers, or to other switches or hubs. - Page 26 Cables Cable Testing for Existing Category 5 Cable Installed Category 5 cabling must pass tests for Attenuation, Near-End Crosstalk (NEXT), and Far-End Crosstalk (FEXT). This cable testing information is specified in the ANSI/TIA/EIA-TSB-67 standard. Additionally, cables must also pass test parameters for Return Loss and Equal-Level Far-End Crosstalk (ELFEXT).
- Page 28 PORTUGUES Informações sobre Suporte Técnico em www.smc.com SWEDISH Information om Teknisk Support finns tillgängligt på www.smc.com INTERNET E-mail address: techsupport@smc.com Driver updates http://www.smc.com/ index.cfm?action=tech_support_drivers_downloads World Wide Web http://www.smc.com/ SMCFS26 20 Mason • Irvine, CA 92618 • Phn: 949-679-8000 • www.smc.com...