Summary of Contents for Datavideo CP-100 PRO
- Page 1 The Commercial CD Media Presenter CP-100 PRO INSTRUCTION MANUAL http://www.datavideo-tek.com...
- Page 2 The Important Notice of Safety Instruction and Radio & TV Interference Read all of these instructions and save them for later reference. Follow all warnings and instructions marked on the products. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners.
- Page 3 It is our goal to make your products ownership a satisfying experience. Our supporting staff is available to assist you in setting up and operating your system. Please refer to our web site www.datavideo-tek.com for answers to common questions, support requests or contact your local office below.
-
Page 4: Radio & Television Interference
RADIO & TELEVISION INTERFERENCE UNITED STATES The equipment described in this guide generates and uses radio frequency energy. If it is not installed and used in accordance with the instructions in this guide, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. -
Page 5: Table Of Contents
CONTENTS RADIO & TELEVISION INTERFERENCE INTRODUCTION ACCESSORIES SUPPLIED ADDITIONAL ACCESSORIES FOR REMOTE CONTROL ADAPTOR REAR PANEL FRONT PANEL INFRARED REMOTE CONTROL HANDSET SYSTEM SETUP OPERATION CONNECTING TO A TV MONITOR CONNECTING TO A VIDEO PROJECTOR OR TV/ MONITOR WITH COMPONENT VIDEO WHAT CAN YOU DO WITH THE GREEN GARD? INSTALLING THE GREEN CARD SPECIFICATIONS... -
Page 6: Introduction
Realtors – Make an attract loop that sells your company and then select video tours of the most likely properties. Give the prospect the CP-100 PRO and let them watch it at home with the family. -
Page 7: Accessories Supplied
Accessories Supplied Infrared Remote Control Handset 2 x “AAA” Batteries for the Handset Power Supply Power Cord 3 Phono (RCA) to 3 Phono (RCA) Audio/Video Cable... -
Page 8: Additional Accessories For Remote Control Adaptor
Additional Accessories for Remote control Adaptor With the optional Momentary Contact Switch Card, all you do is connect switches and a 9-pin cable to the Remote Adaptor (RMC-60). Momentary Contact Switch Card for connecting up to 20-switches for your own Kiosk interface Kiosk Remote Adapter (RMC-60) -
Page 9: Rear Panel
Although there are multiple outputs you can only use one output at a time. If you use more than one simultaneously the output signal level will be reduced. 4. External Switch Remote Interface Connect an external Datavideo Remote Adaptor (RMC-60). Support up to 20- switches for your own Kiosk interface External Remote Adaptor... -
Page 10: Front Panel
5. Fan For proper cooling allow at least 4 inches /10 cm of clear space behind the exhaust fan of the CP-100 PRO 6. Switch to select Cable or Infrared Remote control Switch to select control mode -. Infrared Mode: Enable the Infrared remote control Handset and disable the cable control of RMC-60 -. -
Page 11: Infrared Remote Control Handset
Infrared Remote Control Handset 1. OSD (On Screen Display) Button On screen display, manually activates the display on/off 2. Eject Button Activates the CD tray to open and close 3. Numerical Keypad Selects specific tracks on a disk 4. UP Arrow Key Navigates “Up”... - Page 12 7. Right arrow Key Navigates “Right” on screen menu items 8. Next Button Skips forward to the next track during playback or navigates “down” on the screen menu items 9. ENTER Button Confirm the selected function 10. Down arrow Key Navigates Down on screen menu options 11.
- Page 13 22. Zoom Button Zoom and out of video image. Zoom is a great feature on the CP-100 PRO. It allows you to magnify the image by hitting zoom on remote. Hit once for 1X,twice for 2X up to 8X although 8X is not very sharp.
- Page 14 28. Play List Button Calls up a user programmable Play List of up to 12 tracks 29. Setup Button System configuration for “PAL / NTSC, video/audio output format, etc. 30. Power Button To switch the unit from ON to Standby mode or vice versa 31.
-
Page 15: System Setup
System Setup GENERAL SETUP Press on the “Setup” Button of Remote controller. There will pop up system General setup on TV screen, select the General setup to find more system configuration. TV TYPE Multi ---- Auto-detect the disc video system and output video NTSC/PAL accordingly NTSC -- Output NTSC video PAL ----- Output PAL Video... - Page 16 OSD LANG Select the “English” mode on screen display SPDIF OFF --- Disable the digital audio output, Output Stereo Audio ON ---- Enable the digital audio output, Disable Stereo Audio out...
- Page 17 CAPTIONS ON: Enable Close Caption output OFF: Disable Close Caption output SCR SAVER SCREEN SAVER: No Function on this item...
- Page 18 VIDEO O/P V/S Video: Select S-Video and Composite video output BETACAM: Select component YUV O/P and disable V/S output M-II: Select M-II video O/P and disable V/S output SMPTE: Select SMPTE Video O/P and disable V/S output RGB: Select RGB video O/P and disable V/S output MAIN PAGE Return to the main page of setup screen, Press on the “Setup”...
-
Page 19: Play Mode
There will pop up system setup menu on TV screen, select the MODE Setup to find more system configuration. PLAY MODE DATAVIDEO MODE: Repeat Playback tracks. Play track one repeatedly (as manual track) until pushing a button (or GPI) and then play track two. When track two is done, play track one repeatedly until pushing another button and so on. - Page 20 AUTO RUN Disk in tray will auto play after system power on。 OFF Disk in tray will not auto play after system power on。 JUMP TIME JUMP TIME backward playback 1, 3, 5, 7 SEC Note: Under disk playback mode, press on the Left Arrow Key This is the set up function that allows every press on the left arrow key will go back a pre selected time increment.
- Page 21 OSD DISP Enable on screen display。 OFF Disable on screen display。 MAIN PAGE Return to the main page of setup screen, Press on the “Setup” button of remote controller to go back to normal operation...
-
Page 22: Operation
CP-100 PRO. If it’s already on standby status then press the Power Button on the remote control handset, The CP-100 PRO start up will appear a blue screen on TV. Playing a disk Press the Eject Button on the front of theCP-100 PRO or on the remote control handset and the CD tray will slide open. -
Page 23: Connecting To A Tv Monitor
NOTE: Before making any connections please ensure that the CP-100 PRO and all devices that you are connecting to are switched off. The CP-100 PRO should be connected to the video and audio inputs of a TV Monitor. The TV Monitor may have a European Interface SCART socket, PHONO (RCA) sockets or S-Video socket. -
Page 24: Connecting To A Video Projector Or Tv/ Monitor With Component Video
NOTE: Before making any connections please ensure that the CP-100 PRO and all devices that you are connecting to are switched off. The CP-100 PRO should be connected to the component R.G.B. or Y.U.V. video and audio inputs of a Projector or TV / Monitor. -
Page 25: What Can You Do With The Green Gard
Momentary Contact Switch Card The beauty of the card is that it makes the switch wiring simple if you are building a push button controlled, multi track video kiosk or display. As an exhibit builder your focus is on the message not wiring switches. This card uses convenient screw terminals to connect any kind of SPST contact switches in a simple, logical manner so you can spend your time selecting beautiful switches, engraving buttons or panels and integrating them into the... -
Page 26: Installing The Green Card
Installing the Momentary Contact Switch Card Mount the card so it is convenient for access. It has no active components. Heat is not a factor. After you have selected your switches and where they will be mounted, run two wires from each switch to the appropriate positions on the green card. You may connect either a 9-pin connector or nine wires. - Page 27 Key Matrix: CP-100Pro Control Box D-SUB Pin Definition: Switch 1-10 Connect 1 & 5 1 & 6 1 & 7 1 & 8 1 & 9 2 & 5 2 & 6 2 & 7 2 & 8 2 & 9 D-Sub Pin Switch 11 to 20...
-
Page 28: Specifications
Specifications： Playback Disc A/V Format Playback Disc Type Video format MPEG-II Format DVD-Photo MPEG-II Format S-VCD video resolution MPEG-II Format HQ-VCD video resolution MPEG-I Format VCD video resolution MPEG-I Format Video Outputs: Audio Outputs: Power supply Dimensions Weight DVD/DVD-Photo/SVCD/ HQ-VCD/VCD/Audio CD CD-R, CD-R/W 650MB CCIR601 NTSC and PAL NTSC 704x480 at 30fps... -
Page 29: Q&A
Remote Control Q: How do I turn off/on the (OSD) On Screen Display? A: Via the hand held remote. The CP-100 PRO has a set up memory. You will need the remote to turn it on again. Q: Must I use Datavideo’s VDR-3000 when making CD-s for the CP-100 PRO? A: No…But here are three good reasons why you should consider using it. - Page 30 A: The system goes to the track selected by the most recent button push (contact closure). Q: Does the CP-100 PRO remember the set up configuration? A: Yes. It remembers the last setup change as the next boot default. Q: Can I replace the CD drive myself? A: You can replace it with another CD drive and retain the control features through the DB-9 connector.