Advertisement
Operation Guide 3357
World Time
World Time digitally displays the current time in 30 cities
City code
(29 time zones) around the world.
• For full information on city codes, see the "City Code
NYC
Table".
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
Current time in the
zone of the
selected city code
To view the time in another city
In the World Time Mode, press D to scroll eastwardly through city codes (time
zones).
• The city code is displayed for about two seconds, and then it is replaced with the
current time for that city code. Pressing A while the time is displayed in the World
Time Mode causes the city code of the currently selected zone to appear.
• When the currently selected time zone is one that includes mostly ocean, a value
indicating the zone's Greenwich Mean Time differential appears in place of a city
code.
• If the current time shown for a city is wrong, check your Home City time settings and
make the necessary changes.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use D to display the city
code (time zone) whose Standard Time/Daylight Saving
DST indicator
Time setting you want to change.
2. Hold down A to toggle between Daylight Saving Time
(DST indicator displayed) and Standard Time (DST
indicator not displayed).
• The DST indicator appears on the display whenever you
display a city code for which Daylight Saving Time is
turned on.
• You cannot toggle between Daylight Saving Time and Standard Time if the displayed
city code is
GMT
or the city code that is currently selected as the Home City in the
Timekeeping Mode. To change the DST setting of your Home City, use the
procedure under "To toggle the Timekeeping Mode digital time between DST and
Standard Time" .
• Note that the DST/Standard Time setting affects only the currently displayed city
code. Other city codes are not affected.
Alarm
When the alarm is turned on, the alarm sounds when the
On/Off status
alarm time is reached. You can also turn on an Hourly
Time Signal, which will cause the watch to beep twice
2 seconds
every hour on the hour.
• When the alarm is turned on, the alarm screen
alternates between
alarm time (hour and minutes). When the alarm is off,
qmOw
(alarm off) remains on the alarm screen.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
Alarm Screen
• Pressing D in the Alarm Mode toggles between the
alarm screen and Hourly Time Signal screen.
Press D.
Hourly Time Signal Screen
To set the alarm time
1. In the Alarm Mode, press D to display the alarm
screen.
2. Hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
• This operation automatically turns on the alarm.
3. Press C to move the flashing between the hour and
minute settings.
4. While a setting is flashing, use D (+) and B (–) to
change it.
• When setting the alarm time using the 12-hour format,
Alarm time
(Hour : Minutes)
take care to set the time correctly as a.m. (no
indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds, regardless of the mode the
watch is in.
• To stop the alarm tone after it starts to sound, press any button.
• Alarm and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode digital time.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn the alarm and the Hourly Time Signal on and off
1. In the Alarm Mode, press D to select the alarm or the
Alarm on indicator
Hourly Time Signal screen.
Hourly time signal
2. Press A to toggle the currently selected function on
on indicator
(
Oo
displayed) and off (
• The alarm on indicator and the Hourly Time Signal on
indicator remain on the display in all modes while these
functions are turned on.
On/Off status
qmOo
(alarm on) and the current
Ow
displayed).
Stopwatch
The stopwatch lets you measure elapsed time, split times,
STW
and two finishes.
• The display range of the stopwatch is 59 minutes, 59.99
seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• The elapsed time measurement operation continues
Minutes Seconds
even if you exit the Stopwatch Mode.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
To measure times with the stopwatch
Elapsed Time
D
D
D
Start
Stop
*
1
Re-start
1 When elapsed time measurement is stopped, the display alternates between a
*
minute and seconds screen, and a 1/100 second screen at 2-second intervals.
Minutes' Seconds
Split Time
A
A
D
Start
Split
*
2
Split release
2 Split times are displayed by cycling alternately through the split indicator (
*
a minute and seconds screen, and a 1/100 second screen.
Two Finishes
D
D
A
Start
Split
*
2
Split stop
First runner
Second runner
finishes.
finishes.
Display time of
first runner.
3 When a split time operation is stopped, the display cycles through the same values
*
as those described in *2 above. In this case, however, the minute symbol ( ' ) and
the seconds symbol ( '' ) do not flash.
Illumination
Two LEDs (light-emitting diodes) illuminate the face of the
watch for easy reading in the dark. The watch's auto light
switch automatically illuminates the face when you angle
the watch towards your face.
• The auto light switch must be turned on (indicated by
the auto light switch on indicator) for it to operate.
• You can specify 1.5 seconds or 3 seconds as the
illumination duration.
• See "Illumination Precautions" for other important
Auto light switch
information.
on indicator
To illuminate the face of the watch manually
In any mode (except when a setting screen is on the display), press B to illuminate
the face of the watch.
• The above operation turns on illumination regardless of the current auto light switch
setting.
About the Auto Light Switch
Turning on the auto light switch causes the face to illuminate, whenever you position
your wrist as described below in any mode. Note that this watch features a "Full Auto
LED Light", so the auto light switch operates only when available light is below a
certain level. It does not illuminate the face under bright light.
Moving the watch to a position that is parallel to the ground and then tilting it
towards you more than 40 degrees causes illumination to turn on.
• Wear the watch on the outside of your wrist.
Parallel to
ground
Warning!
• Always make sure you are in a safe place whenever you are reading the face
of the watch using the auto light switch. Be especially careful when running or
engaged in any other activity that can result in accident or injury. Also take
care that sudden illumination by the auto light switch does not surprise or
distract others around you.
• When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create a
distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In any mode (except when a setting screen is on the display), hold down B for about
two seconds to toggle the auto light switch on (
displayed).
• The auto light switch on indicator (
) is on the display in all modes while the auto
light switch is turned on.
• The auto light switch turns off automatically whenever battery power drops to Level 3.
• The auto light switch is disabled, regardless of its on/off setting, when the Hand
Setting Mode's setting screen.
D
A
Stop
*
1
Clear
1/100 second
D
A
Stop
*
1
Clear
),
SPL
A
A
*
3
*
1
Clear
Split release
Display time of
second runner.
More than
40 °
displayed) and off (
not
2
Hide quick links:
Advertisement
