Battery Use And Safety; European Union Directives Conformance Statement; Service And Repairs; Specific Absorption Rate Data - Motorola MOTOROKR U9 Getting Started Manual

the small print
battery use & safety
IMPORTANT: HANDLE AND STORE BATTERIES PROPERLY TO AVOID INJURY OR
DAMAGE. Most battery issues arise from improper handling of batteries, and particularly
from the continued use of damaged batteries.
DON'Ts
• Don't disassemble, crush, puncture, shred, or otherwise attempt to change
the form of your battery.
• Don't let the phone or battery come in contact with water. Water can get into
the phone's circuits, leading to corrosion. If the phone and/or battery get wet, have
them checked by your carrier or contact Motorola, even if they appear to be working
properly.
• Don't allow the battery to touch metal objects. If metal objects, such as jewelry,
stay in prolonged contact with the battery contact points, the battery could become
very hot.
• Don't place your battery near a heat source. Excessive heat can damage the
phone or the battery. High temperatures can cause the battery to swell, leak, or
malfunction. Therefore:
• Do not dry a wet or damp battery with an appliance or heat source, such as a hair
dryer or microwave oven.
• Avoid leaving your phone in your car in high temperatures.
DOs
• Do avoid dropping the battery or phone. Dropping these items, especially on a
hard surface, can potentially cause damage.
• Do contact your service provider or Motorola if your phone or battery has
been damaged from dropping or high temperatures.
IMPORTANT: USE MOTOROLA ORIGINAL PRODUCTS FOR QUALITY ASSURANCE
AND SAFEGUARDS. To aid consumers in identifying authentic Motorola batteries from
non-original or counterfeit batteries (that may not have adequate safety protection),
Motorola provides holograms on its batteries. Consumers should confirm that any battery
they purchase has a "Motorola Original" hologram.
Motorola recommends you always use Motorola-branded batteries and
chargers. Motorola mobile devices are designed to work with Motorola batteries. If you
see a message on your display such as Invalid Battery or Unable to Charge, take the
following steps:
• Remove the battery and inspect it to confirm that it has a "Motorola Original"
hologram;
• If there is no hologram, the battery is not a Motorola battery;
• If there is a hologram, replace the battery and retry charging it;
• If the message remains, contact a Motorola Authorized Service Center.
Important: Motorola' s warranty does not cover damage to the phone caused by
non-Motorola batteries and/or chargers.
Warning: Use of a non-Motorola battery or charger may present a risk of fire, explosion,
leakage, or other hazard.
PROPER AND SAFE BATTERY DISPOSAL AND RECYCLING
Proper battery disposal is not only important for safety, it benefits the environment.
Consumers may recycle their used batteries in many retail or service provider locations.
Additional information on proper disposal and recycling may be found on the Web:
• www.motorola.com/recycling
• www.rbrc.org/call2recycle/ (in English only)
Disposal: Promptly dispose of used batteries in accordance with local
regulations. Contact your local recycling center or national recycling
organizations for more information on how to dispose of batteries.
Warning: Never dispose of batteries in a fire because they may explode.
service & repairs
If you have questions or need assistance, we're here to help.
Go to www.motorola.com/support, where you can select from a number of customer
care options. You can also contact the Motorola Customer Support Center at
1-800-331-6456 (United States), 1-888-390-6456 (TTY/TDD United States for hearing
impaired), or 1-800-461-4575 (Canada).

Specific Absorption Rate Data

SAR Data
This model wireless phone meets the government's requirements for
exposure to radio waves.
Your wireless phone is a radio transmitter and receiver. It is designed and manufactured
not to exceed limits for exposure to radio frequency (RF) energy set by the Federal
Communications Commission (FCC) of the U.S. Government and by the Canadian
regulatory authorities. These limits are part of comprehensive guidelines and establish
permitted levels of RF energy for the general population. The guidelines are based on
standards that were developed by independent scientific organizations through periodic and
thorough evaluation of scientific studies. The standards include a substantial safety margin
designed to assure the safety of all persons, regardless of age or health.
The exposure standard for wireless mobile phones employs a unit of measurement known
as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC and by the Canadian
1
regulatory authorities is 1.6 W/kg. Tests for SAR are conducted using standard operating
positions accepted by the FCC and by Industry Canada with the phone transmitting at its
highest certified power level in all tested frequency bands. Although the SAR is determined
at the highest certified power level, the actual SAR level of the phone while operating can
be well below the maximum value. This is because the phone is designed to operate at
multiple power levels so as to use only the power required to reach the network. In general,
the closer you are to a wireless base station, the lower the power output.
Before a phone model is available for sale to the public in the U.S. and Canada, it must be
tested and certified to the FCC and Industry Canada that it does not exceed the limit
established by each government for safe exposure. The tests are performed in positions and
locations (e.g., at the ear and worn on the body) reported to the FCC and available for review
by Industry Canada. The highest SAR value for this model phone when tested for use at the
ear is 1.36 W/kg, and when worn on the body, as described in this user guide, is 0.56 W/kg.
The SAR value for this product in its data transmission mode (body-worn use) is 1.36 W/kg.
(Body-worn measurements differ among phone models, depending upon available
accessories and regulatory requirements).
While there may be differences between the SAR levels of various phones and at various
positions, they all meet the governmental requirements for safe exposure. Please note that
improvements to this product model could cause differences in the SAR value for later
products; in all cases, products are designed to be within the guidelines.
Additional information on Specific Absorption Rates (SAR) can be found on the Cellular
Telecommunications & Internet Association (CTIA) Web site:
http://www.phonefacts.net
or the Canadian Wireless Telecommunications Association (CWTA) Web site:
http://www.cwta.ca
1. In the United States and Canada, the SAR limit for mobile phones used by the public is
1.6 watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a substantial
margin of safety to give additional protection for the public and to account for any variations in
measurements.
2 The SAR information includes the Motorola testing protocol, assessment procedure, and
measurement uncertainty range for this product.

European Union Directives Conformance Statement

Hereby, Motorola declares that this product is in compliance with:
EU Conformance
•The essential requirements and other relevant provisions of Directive
1999/5/EC
•All other relevant EU Directives
0168
The above gives an example of a typical Product Approval Number.
You can view your product's Declaration of Conformity (DoC) to Directive 1999/5/EC (to
R&TTE Directive) at www.motorola.com/rtte. To find your DoC, enter the Product Approval
Number from your product's label in the "Search" bar on the Web site.

OPEN SOURCE SOFTWARE INFORMATION

For instructions on how to obtain a copy of any source code being made publicly available by
OSS Information
Motorola related to software used in this Motorola mobile device you may send your
request in writing to:
MOTOROLA, INC.
OSS Management
600 North US Hwy 45
Libertyville, IL 60048
USA
The Motorola website opensource.motorola.com also contains information regarding
Motorola's use of open source.
Motorola has created the opensource.motorola.com to serve as a portal for interaction
with the software community-at-large.
2
Product
Approval
Number