WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING : To reduce the risk of electric shock do not remove cover or back. No user-serviceable parts inside refer service to qualified service personnel. Safety of operators has been taken into consideration at the design and manufacture phase, but inappropriate operation may cause electric shock or fire.
8. Power Source ---This unit should be operated only from the type of power source indicated on the rating label. If you are not sure of the type of power supply to your home, consult your Appliance dealer or local power company.
Page 4
15.Heat --- The product should be situated away heat source such as radiators, heat registers, stoves, or other products (Including amplifiers) that product heat. 16.Overloading ---Do not overload wall outlets and extension cord as this can result in a risk of Fire or Electric shock.
....... Timer menu ..........External Equipment Connections ..Timer setting ........Operation On/off timer\Timer on Prog\Timer Prog ... Set up your TV........Function menu.......... Switching ON/OFF the TV set... Function setup ........Choose the Menu Language..... Adjust menu ..........Select input modes ......
-This is a simplified representation of front panel. -Here shown may be somewhat different from your TV. Front control panel 1.EXIT: clears all on-screen displays and returns to TV viewing from any menu. 2.INPUT: Source input select 3.CH- /CH+ Program plus and minus, menu options 4.VOL-/VOL+...
1. AUDIO OUT: Connect to optional external speaker(s). 2.VGA IN(PC) Connect VGA analog cable from the PC to the VGA IN. Connect the audio cable from the PC to the VGA AUDIO IN. 3.COMPONENT IN Connect the component cables from the component output of the video device to COMPONENT IN.
Precautions Make sure that two AA alkaline batteries As strong light may interfere the are loaded. The batteries must be of the signals, change your position to same type. The batteries must be located operate the remote controller if properly.
Keys of remote controller - The remote controller cannot be operated unless the batteries are properly loaded. - When using the remote control, aim it at the remote control sensor on the TV. Function introduction STILL I/II (NICAM) Picture static...
No obstacles should be placed between the remote controller and the remote controller window. The effective receiving scope for the signal is 8 meters to the front of the remote controller window, and 45 to the left or right side and 20 above or below the control window.
External Equipment Connections Antenna Connection Generally speaking, to enjoy a clearer picture, we recommend that you use a CATV system or an outdoor antenna .In different places, the suitable antenna type and position are different. outdoor Mixer antenna additional purchase...
Choose Your Connection There are several ways to connect your television, depending on the components you want to connect and the quality of the signal you want to achieve. The following are examples of some ways to connect your TV.
DVD connection How to connect . Connect the DVD video outputs (Y, Pb/Cb, Pr/Cr) to the YUV IN jacks on the TV and connect the DVD audio outputs to the AUDIO IN jacks on the TV, as shown in the figure.
Page 14
The fixed PC sound as required. i m a g e m a y b e c o m e p e r m a n e n t l y How to use imprinted on the screen.
External Equipment Connections Connecting Headphones You can connect a set of headphones to your set if you wish to watch a TV programme without disturbing the other people in the room. Plug a set of headphones into the 3.5mm mini-jack socket on the rear panel of the set.
Set up your TV -There are several options you might need to set up in order for your TV to work properly. Read the instructions that follow. -In the manual, the OSD(on screen display) may be different from your TV`s, because it is just an example to help you with the TV operation.
If you hope to enjoy the picture from the external input source, before to select the source, you need to connect the devices, otherwise, when you select the source, the none or no signal will appears on the screen. MUTE...
This TV set has three methods to set channels, which are respectively full automatic, manual search fine tune. In this section, how to use the remote control to set channel is explained. You can also use buttons on the TV set to set channel. Full automatic search mode...
Press CH+/- to select the channel, and press the yellow button on the remote controller, and press the yellow button to display the digital and letter list, press Vol+/- or CH+/- to select the desired digital or letter, press the yellow button to exit list, then press MENU button to ensure.
Tuning menu Manual search If excessive channel signals of unwanted programs are received in local area, manual search function is recommended. Press CH+/- buttons or the NUMBER 0-9 button to choose desired searching frequency. MUTE STILL (regard channel 18 as example).
Tuning menu Fine Tuning If the picture and/or sound are poor, try using the FINE TUNING feature. Do not use this feature unless reception is poor. Press CH+/- button or MUTE STILL c 28 NUMBER 0-9 button to AUTO choose desired channels...
ABC@ entry. If wrong password is entered, channel selection GHI$ JKL% will fail and previous program will still stay on the screen. POR& STUV WXYZ The program locking password can be modified in the...
Tuning menu If the colour of some channel is abnormal Usually this should be set in the auto position. However if the colour displayed on the screen are incorrect, you can manually select the correct colour system. MUTE STILL Press the MENU CH+/-and...
2. Do the above steps again. 3. Press VOL+/- button to set Skip Off. Program swap Swap function enables quick swap to the last watched program. Suppose the channel number you used just now is 8 and the channel number you are using is 18 (as shown in the figure).
TIMER Noise Reduction Auto Press the CH+/- button t o s e l e c t t h e i t e m t o adjusted, then press the Note: 1. the hue item is available only in NTSC system.
Picture menu Noise Reduction Automatically filters out and reduces the image noise and improves picture quality when receiving weak video signals. MUTE STILL After calling up the DISPLAY SCAN SLEEP Picture menu, press ABC@ CH+/- button to select GHI$ "Noise Reduction"...
The intermediate value is 0. When indication value of Balance increases toward+50, sound of the right and left speaker becomes stronger and weaker, respectively. When indication value of Balance decreases toward -50, sound of the right and left speaker becomes weaker and stronger. Press MENU button and then CH+/- button to select AUDIO menu.
TV`s speakers. Select Surround from -50 to +50 . When intermediate value toward +50, the effect will be distinctness. Repeated step 1-2, and press CH+/- to select surround, and...
Auto Volume Each broadcasting station has its own signal conditions, and so it is not easy for you to adjust the volume every time the channel is changed. This feature lets you automatically adjust the volume of the desired channel and reduces the volume differences between channels and programs, providing a more constant overall level.
Timer menu Timer setting The clock will only work if the TV set is turned on or in standby. When the set is disconnect from the power supply or is turned off by the main power on the rear panel, the clock loses...
Timer menu You can set the On/Off timers so that the set will : Switch on automatically and tune to the channel of your choice at the time you select. Switch off automatically at the time you select. On/off timer \Timer on Prog\ Timer Prog Press MENU and VOL+/- button to call up the TIMER menu on the screen.
TIMER ZOOM EXIT Menu Timeout Repeat step 3 and 4 to select the time of the OSD display in sequence as follows: 5 seconds,10 seconds, 15seconds, 20seconds, 25seconds, 30 seconds and 40 seconds. Menu Background Repeat step 3 and 4 to select Transparent / Opaque background of OSD.
CH+/- to adjust them. TV/AV SWAP P.STD S.STD Teletext Language Repeat step 3 and 4 to select from 6 kinds of languages. (West Europe/East Europe/Cyrillic/Greek/Arabic/Persian.) VOL- MENU VOL+ Restore Default Value Repeat step 3 and 4 to return the factory mode.
VOL- MENU VOL+ 4:3 mode Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both the left and right sides. H.LOCK Using the MENU button.
Adjust menu In VGA and HDMI input mode, H-Position and V-Position can be adjusted to eliminate transverse line interference and decentered picture as follows: H-Position and V-Position adjust Adjust is opted for adjusting H-Position and V-Position as well as relative parameters in VGA and HDMI modes.
Adjust menu RGB/Default/Auto Sync 1) RGB is opted for adjustment of the numerical value of red, green and blue in VGA,HDMI mode. 2) Default is opted for adjustment of parameters to delivery setup in VGA mode.(After the operation, complete will be on...
Password needs to be entered when the program lock mode is to be set. *#() TV/AV SWAP Note: If the password is not correctly entered, you will be P.STD S.STD required to reenter the password and the cursor will stay at the first place.
(To set On, some operation such as search will be not available. When enter the TUNING menu, Tuner Lock will be on the screen, and the time will be the same with the main menu if no operation. If you want to operate TUNING menu, you need to enter the Lock menu to set Tuner Lock Off or operate Clear Lock.
Lock Set menu is set, current volume will become set m a x i m u m v o l u m e . I f c u r r e n t v o l u m e i s b e l o w maximum volume, customer set volume will stay H.LOCK...
If the DISPLAY button is pressed again, the displayed information will disappear. VOL- MENU VOL+ (If the program is named, its name will also appear ). Auto program scan H.LOCK CH.LIST TIMER ZOOM EXIT...
Page 41
CH.LIST TIMER ZOOM EXIT Press Still button, the picture will be still; if to cancel, press Still button again, the picture will resume. Auto switch-off function If an empty channel is selected or the TV programs are ended for the day, the power will be switched off 5 minutes later automatically.
Teletext functions Teletext is an information system, broadcast by certain channels, which can be read like a newspaper . It also provides subtitles for people with hearing difficulties or those who are unfamiliar with the language in which a particular programme is being broadcast (cable networks, satellite channels, etc.).
Page 43
Teletext functions (MIX) While in Teletext mode press the button will show the teletext data superimposed on top of the TV picture. Press the button again to revert back to Full text. (HOLD) Pressing the button will stop the teletext page automatically updating.
Cleaning the Screen . Here`s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it`s almost dry, and then use it to wipe the screen.
(red, blue or green) spots, or some anomalistic stripes or spots. This is not defect. If the TV set is used in an area 2,400 meters above the sea level where the air pressure is below 750hpa, the picture on the plasma screen may be affected and a muffled sound might be produced.