Omron F3SH-A Datasheet page 14

Stand-alone
Model
Series con- F3SN-A@@@@P14-01
Item nection (see notes 1, 2 and 8)
IEC61496-1, EN61496-1 Type 4 ESPE (Electro-Sensitive Protective Equipment)
Applicable standard
IEC61496-2 Type 4 AOPD (Active Opto-electronic Protective Devices)
Note: 1 . The 4 digits in @@@@ in the model number represent the protective height. Use the formula given in the information on protective height specifications to
calculate the height.
For example, if the beam gap is 9 mm, and the No. of beams is 21, the protective height will be 9 × 21 = 189 mm. The model with this protective height is
F3SN-A0189P14.
2 . F3SN-A@@@@P14-01 is a customized model. Consult with your OMRON representative when ordering this model.
3 . Models ending in -01 only.
4 . For the factory setting, the manual reset mode is set to the "start/restart" interlock.
Using the F39-MC11 can select either the start interlock or the restart interlock.
5 . For the factory setting, the function is not set. It can be enabled with the F39-MC11.
6 . Not provided with the F3SN-A@@@@P70 and F3SH-A.
7 . The intermediate mounting bracket is supplied with the following types:
Types which have the total length of the light curtain from 640 mm to 1280 mm: 1 set for each of emitter and receiver.
Types which have the total length of the light curtain over 1280 mm: 2 sets for each of emitter and receiver.
8 . For sizes above 1,125 mm add „H" after P14, e.g. F3SN-A1143P14H. Ask for supplemental manual.
Accessories
Control unit
Item Model
Applicable sensor
Supply voltage
Power consumption
Operating time
Response time
No. of contact
Relay output Rated load
Rated carry voltage
Between sensor's
Connection
method
Other
Weight (in packaging)
Accessory
Note: 1 . For further details on the G9SA-300-SC, refer to the G9SA catalogue.
Setting console
Item Model
Applicable sensor F3SN-A, F3SH-A
Supply
24 V DC ±10% (supplied from sensor)
voltage
Connection
Special cable (accessory)
method
Weight
360 g
(Packed state)
Branch connector (1), special cable (2 m),
Accessories
connector cap (1), operation manual
For details on the setting console,
see the manual included with the product.
Environment-resistant Enclosure
Item
Applicable sensor
Operating range characteristics
Degree of protection (see note)
Materials
Note: To conform to IP67, tighten the screws according to the "Cautions for Use" as described in the manual packaged together with the product.
G-16
F3SN-A@@@@P14 F3SN-A@@@@P25
(see notes 1 and 8) (see note 1)
F3SN-A@@@@P25-01
(see note 1)
F3SP-B1P
F3SN-A, F3SH-A
24 VDC ±10%
1.7 W DC max. (does not include the sensor's
current consumption)
100 ms max. (does not include the sensor's
response time)
10 ms max. (does not include the sensor's
response time)
3 NO + 1 NC
25 VAC, 5 A (cos diameter = 1), 30 VDC, 5 A L/R = 0 ms
5 A
M12 connector (8 pins)
Terminal block
Approx. 280 g
Instruction manual
F39-MC11
Model F39-HP@@@@-14
F3SN-A@@@@P14(-01)
0.2 to 6 m
IP67 (IEC60529)
Case: Acrylic resin, rubber: NBR60, mounting bracket: SUS316L, screw: SUS316L
F3SN-A@@@@P40 F3SN-A@@@@P70
(see note 1) (see note 1)
F3SN-A@@@@P40-01 F3SN-A@@@@P70-01
(see note 1) (see note 1)
24 VDC: 0.7 WDC max. (does not include the
sensor's current consumption)
300 ms max. (does not include the sensor's
response time and bouncetime)
10 ms max. (does not include the sensor's
response time and bouncetime)
3 NO
250 VAC, 5 A
Approx. 300 g
Large indicator lamps
Model F39-A01PR-L
(for emitter)
F39-A01PR-D
Item (for light receiver)
Applicable sensor F3SN-A####P##-01 F3SH-A09P03-01
Light source Red LED
Supply
24 V DC ±10% (supplied by sensor)
voltage
Current
40 mA or less (supplied by sensor)
consumption
Connection
M12 connector (8-pin)
method
Weight
80 g
(Packed state)
F3SN-A@@@@P25(-01)/P40(-01)/P70(-01),
F3SH-A09P03(-01)
0.2 to 10 m
Safety Sensors / Components
F3SH-A09P03
F3SH-A09P03-01
G9SA-300-SC (See note)
F39-A01PG-L
(for emitter)
F39-A01PG-D
(for light receiver)
Green LED
F39-HP@@@@-25
F39-HPH09-03