Related Manuals for Sennheiser HSP 2 - 01-08
Summary of Contents for Sennheiser HSP 2 - 01-08
- Page 1 HSP 2 HSP 4 Bedienungsanleitung Instructions for use Notice d‘emploi Istruzioni per l‘uso Instrucciones de uso Gebruiksaanwijzing...
-
Page 2: Table Of Contents
Delivery includes ..................3 HSP 2/HSP 4..................... 4 Putting the HSP 2 into operation ............5 Attaching the microphone to the left or right side ....5 Adjusting the microphone boom and the neckband ....7 Windshields for the HSP 2 ............. 9 Treble boost using the frequency response caps ....10... -
Page 3: Safety Instructions
• Do not expose the device to extreme temperatures (normal operating temperatures: 10 °C to 35 °C). • Use the device with care and store it in a clean, dust-free environment. Intended use of the device Intended use includes: •... -
Page 4: Delivery Includes
Delivery of the HSP 2/HSP 4 includes: 1 boom microphone 1 neckband 5 clips 1 silicone tube 1 connection cable 1 plastic transport case, foam-lined with cut-outs 1 windshield (HSP 4 only) 2 caps, short and long (HSP 2 only) 1 instruction manual 1 Warranty Certificate... -
Page 5: Hsp 2/Hsp 4
The 24 available HSP variants differ in size, color and connector (see “HSP 2 cable variants” on page 11 and “HSP 4 cable variants” on page 17). There are two pick-up patterns available: •... -
Page 6: Putting The Hsp 2 Into Operation
Putting the HSP 2 into operation The HSP 2 is ready for operation on delivery. The microphone can be worn on the left or right side of the mouth. If you do want to change sides, continue on page 7. - Page 7 To reattach the microphone boom: First press the microphone boom and then the neckband into the clip as shown. Close the clip.
-
Page 8: Adjusting The Microphone Boom And The Neckband
Adjusting the microphone boom and the neckband For best possible comfort and optimum fit of the headmic, the neckband and the microphone boom have to be adjusted to properly fit your head. CAUTION! Damage to the microphone boom! The microphone boom can break or be impaired in its function when you bend or turn it in the wrong place. - Page 9 Adjusting the neckband The neckband is flexible and ensures an optimum fit. Change the length of the neckband until a snug but comfortable fit is achieved. If necessary, adjust the neck- band at the earhooks. Attaching the cable to the cable...
-
Page 10: Windshields For The Hsp 2
An effective attenuation of wind noise can be » obtained by using the MZW 2 and the MZW 02 windshields. To begin with, use the MZW 2 windshield which reduces wind noise by a maximum of 20 dB. -
Page 11: Treble Boost Using The Frequency Response Caps
Use these caps if the microphone cannot be positioned close to the mouth. The further away the microphone is from the mouth, the less treble is picked up. In addition, you should use these caps if the sound is too muffled or if you want to increase the speech intelligibility. -
Page 12: Hsp 2 Cable Variants
The headmics are available in two sizes. The -M variants have smaller neckbands and shorter microphone booms. Connection cable with 3-pin lockable special connector Suitable for Sennheiser SK 50, SK 250, SK 5012 and SK 3063 bodypack transmitters. HSP 2 anthracite Cat. -
Page 13: Putting The Hsp 4 Into Operation
Putting the HSP 4 into operation The HSP 4 is ready for operation on delivery. The microphone can be worn on the left or right side of the mouth. If you do want to change sides, continue on page 14. - Page 14 To reattach the microphone boom: First press the microphone boom and then the neckband into the clip as shown. Close the clip.
-
Page 15: Adjusting The Microphone Boom And The Neckband
Adjusting the microphone boom and the neckband For best possible comfort and optimum fit of the headmic, the neckband and the microphone boom have to be adjusted to properly fit your head. CAUTION! Damage to the microphone boom! The microphone boom can break or be impaired in its function when you bend or turn it. -
Page 16: Attaching The Sound Inlet Basket
Attaching the sound inlet basket Notes: – Do not position the microphone directly in front of your mouth as it will pick up your breathing and plosive noises from your mouth. In addition, moisture can adversely affect the sound and performance of your microphone. -
Page 17: Attaching The Cable To The Cable Grip
Attaching the cable to the cable grip Attach the microphone cable to the cable grip in the centre of the neckband. Note: When attaching the thin cable, make sure you also press the small cable sleeve into the cable grip or the cable will fall out. -
Page 18: Hsp 4 Cable Variants
The headmics are available in two sizes. The -M variants have smaller neckbands and shorter microphone booms. Connection cable with 3-pin lockable special connector Suitable for Sennheiser SK 50, SK 250, SK 5012 and SK 3063 bodypack transmitters. HSP 4 anthracite Cat. -
Page 19: Care And Maintenance
Only use a soft, slightly damp cloth to clean the device. Cleaning the sound inlet basket (HSP 4 only) To clean or replace the sound inlet basket, carefully pull it from the capsule. Moisten a small brush (bristle brush or toothbrush) with isopropyl alcohol. - Page 20 Cleaning the contacts of the connection cable Over time, salt deposits from sweat can build up on the connector and the socket. Clean the connector and the socket using standard isopropyl alcohol. To loosen the connection: Slide the silicone tube aside.
- Page 21 Dry the connector and the socket using a soft cloth or a small piece of cotton wool and carefully tap them off. Allow the connector and the socket to air dry for approx. 1 hour so that the remaining isopropyl alcohol can evaporate.
-
Page 22: Accessories/Spare Parts
Accessories/spare parts The following accessories and/or spare parts are available for the HSP 2 / HSP 4: Spare parts for HSP 2 Parts Cat. No. Boom microphone, omni-directional, beige 511711 Boom microphone, omni-directional, anthracite 511712 HSP-M boom microphone, omni-directional, anthracite 515280... - Page 23 510862 MZW 4 foam windshield, beige 510863 Set of clips for HSP 4, beige 528167 Set of clips for HSP 4, black 528168 Spare parts for HSP 2 and HSP 4 Parts Cat. No. Neckband, anthracite 511709 Neckband, beige 511710...
-
Page 24: Specifications
Cable length 1.6 m Diameter of boom arm 1.1 mm Weight HSP 2/HSP 2-M 2.1 g/2.0 g Connector see “HSP 2 cable variants” on page 11 Neckband Width HSP 2/HSP 2-M 110 mm/80 mm Weight HSP 2/HSP 2-M 4.4 g/4.0 g... - Page 25 180° 125 Hz 2000 Hz 250 Hz 4000 Hz 500 Hz 8000 Hz 16000 Hz 1000 Hz Frequency response curve HSP 2 - 35 - 40 - 45 - 50 - 55 - 60 - 65 - 70 1000 2000...
-
Page 26: Specifications Hsp 4/Hsp 4-M
Cable length 1.6 m Diameter of boom arm 2.0 mm Weight HSP 4/HSP 4-M 4.8 g/4.0 g Connector see “HSP 4 cable variants” on page 17 Neckband Width HSP 4/HSP 4-M 110 mm/80 mm Weight HSP 4/HSP 4-M 4.4 g/4.0 g... - Page 27 180° 125 Hz 2000 Hz 250 Hz 4000 Hz 500 Hz 8000 Hz 16000 Hz 1000 Hz Frequency response curve HSP 4 - 35 - 40 - 45 - 50 - 55 - 60 - 65 - 70 5000 10000 20000 Hz 1000 2000 0°, 1 m...
-
Page 28: Manufacturer Declarations
Directive 2004/108/EC. The declaration is available on the Internet at www.sennheiser.com. WEEE Declaration Please dispose of this product at the end of its operational lifetime by taking it to your local collection point or recycling center for such equipment. - Page 29 Sennheiser electronic GmbH & Co. KG Am Labor 1, 30900 Wedemark, Germany Phone +49 (5130) 600 0 Printed in Germany Fax +49 (5130) 600 300 Publ. 01/08 www.sennheiser.com 527045/A01...