Table of Contents
Advertisement
EN 24
5.
TPM6.1E LA
5. Service Modes, Error Codes, and Fault Finding
Index of this chapter:
5.1 Test Points
5.2 Service Modes
5.3 Stepwise Start-up
5.4 Service Tools
5.5 Software Upgrading
5.6 Error Codes
5.7 The Blinking LED Procedure
5.8 Fault Finding and Repair Tips
5.1
Test Points
As most signals are digital, it will be difficult to measure
waveforms with a standard oscilloscope. However, several key
ICs are capable of generating test patterns, which can be
controlled via ComPair. In this way it is possible to determine
which part is defective.
Perform measurements under the following conditions:
•
Service Default Mode.
•
Video: Colour bar signal.
•
Audio: 3 kHz left, 1 kHz right.
5.2
Service Modes
The Service Mode feature is split into four parts:
•
Service Default Mode (SDM).
•
Service Alignment Mode (SAM).
•
Customer Service Mode (CSM).
•
Computer Aided Repair Mode (ComPair).
SDM and SAM offer features, which can be used by the Service
engineer to repair/align a TV set. Some features are:
•
A pre-defined situation to ensure measurements can be
made under uniform conditions (SDM).
•
Activates the blinking LED procedure for error identification
when no picture is available (SDM).
•
Make alignments (e.g. White Tone), reset the error buffer
(SAM).
•
Display information ("SDM" or "SAM" indication in upper
right corner of screen, error buffer, software version,
operating hours, options and option codes, sub menus).
The CSM is a Service Mode that can be enabled by the
consumer. The CSM displays diagnosis information, which the
customer can forward to the dealer or call centre. In CSM
mode, "CSM", is displayed in the top right corner of the screen.
The information provided in CSM and the purpose of CSM is to:
•
Increase the home repair hit rate.
•
Decrease the number of nuisance calls.
•
Solved customers' problem without home visit.
ComPair Mode is used for communication between a computer
2
and a TV on I
C /UART level and can be used by a Service
engineer to quickly diagnose the TV set by reading out error
codes, read and write in NVMs, communicate with ICs and the
mP (PWM, registers, etc.), and by making use of a fault finding
database. It will also be possible to up and download the
software of the TV set via I
ComPair has to be connected to the TV set via the ComPair
connector, which will be accessible through the rear of the set
(without removing the rear cover).
Note: For the new model range, a new remote control (RC) is
used with some renamed buttons. This has an impact on the
activation of the Service modes. For instance the old "MENU"
button is now called "HOME" (or is indicated by a "house" icon).
5.2.1
General
Next items are applicable to all Service Modes or are general.
2012-Jan-20
Service Modes, Error Codes, and Fault Finding
2
C with help of ComPair. To do this,
Life Timer
During the life time cycle of the TV set, a timer is kept (called
"Op. Hour"). It counts the normal operation hours (not the
Stand-by hours). The actual value of the timer is displayed in
SDM and SAM in a decimal value. Every two soft-resets
increase the hour by + 1. Stand-by hours are not counted.
Software Identification, Version, and Cluster
The software ID, version, and cluster will be shown in the main
menu display of SDM, SAM, and CSM.
The screen will show: "AAAAAB-XX.YY", where:
•
AAAAA is the chassis name: TPM61E x.yy. (Thriller) and
TPM62E x.yy (Berlinale).
•
B is the region indication: E = Europe, A = AP/China, U =
NAFTA, L = LATAM.
•
XX is the main version number: this is updated with a major
change of specification (incompatible with the previous
software version). Numbering will go from 01 - 99 and
AA - ZZ.
- If the main version number changes, the new version
number is written in the NVM.
- If the main version number changes, the default settings
are loaded.
•
YY is the sub version number: this is updated with a minor
change (backwards compatible with the previous
versions). Numbering will go from 00 - 99.
- If the sub version number changes, the new version
number is written in the NVM.
- If the NVM is fresh, the software identification, version,
and cluster will be written to NVM.
Display Option Code Selection
When after an SSB or display exchange, the display option
code is not set properly, it will result in a TV with "no display".
Therefore, it is required to set this display option code after
such a repair.
To do so, press the following key sequence on a standard RC
transmitter: "062598" directly followed by MENU and "xxx",
where "xxx" is a 3 digit decimal value of the panel type: see
column "Display Code" in
Table
side/bottom of the cabinet. When the value is accepted and
stored in NVM, the set will switch to Stand-by, to indicate that
the process has been completed.
Display Option
Code
39mm
PHILIPS
040
MODEL:
32PF9968/10
PROD.SERIAL NO:
AG 1A0620 000001
(CTN Sticker)
Figure 5-1 Location of Display Option Code sticker
During this algorithm, the NVM-content must be filtered,
because several items in the NVM are TV-related and not SSB
related (e.g. Model and Prod. S/N). Therefore, "Model"
and "Prod. S/N" data is changed into "See Type Plate". In case
a call centre or consumer reads "See Type Plate" in CSM
mode, the consumer needs to look to the side/bottom sticker to
identify the set, for further actions.
6-2, or see sticker on the
10000_038_090121.eps
090819
Advertisement
Table of Contents
