Page 4
ㆍDescription of your software (operating system, version, application software, etc.) ㆍA complete description of the problem ㆍThe exact wording of any error messages To receive the latest version of the user’s manual; please visit our Web site at: www.avalue.com 4 ESM-RPLC User’s Manual...
Page 5
On the other hand, if the new product defect is resulting from incorrect configuration or erroneous use by the user instead of any problem of the hardware itself, the customer will also be requested to pay for relevant handling fees. ESM-RPLC User’s Manual...
Page 6
Lacking detailed statement of fault steps also makes the problem hard to be identified, sometimes resulting in second-time repairs. 6 ESM-RPLC User’s Manual...
Page 7
• Product has been altered or its label of the serial number has been torn off. • Product functionality issues resulting from improper use by the user, unauthorized dismantle or alteration, unfit operation environment, improper maintenance, accident ESM-RPLC User’s Manual...
Page 8
If the customer demands an additional maintenance analysis report, a service fee of various level will be charged depending on the warranty status. In case the analysis result shows that the defect attributes to Avalue’s faulty design or process, the analysis fee will be exempted. 8 ESM-RPLC User’s Manual...
Page 9
9. Position the power cord so that people cannot step on it. Do not place anything over the power cord. 10. All cautions and warnings on the equipment should be noted. 11. If the equipment is not used for a long time, disconnect it from the power source to ESM-RPLC User’s Manual...
Page 10
The equipment has obvious signs of breakage. 14. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. 15. Equipment intended only for use in a RESTRICTED ACCESS AREA. 10 ESM-RPLC User’s Manual...
Page 11
A NOTE provides additional information intended to avoid Note inconveniences during operation. Direct current. Alternating current Stand-by, Power on FCC Certification CE Certification Follow the national requirements for disposal of equipment. Stacking layer limit This side up ESM-RPLC User’s Manual 11...
Page 12
ESM-RPLC User’s Manual Fragile Packaging Beware of water damage, moisture-proof Carton recyclable Handle with care Follow operating instructions of consult instructions for use. 12 ESM-RPLC User’s Manual...
Page 13
EXPLOSION ou une fuite de liquide ou de gaz inflammable. - UNE BATTERIE soumise à une pression d'air extrêmement basse pouvant entraî ner une EXPLOSION ou une fuite de liquide ou de gaz inflammable. ESM-RPLC User’s Manual 13...
Using Setup ......................51 Getting Help ......................52 In Case of Problems ....................52 BIOS setup ......................53 4.6.1 Main Menu ............................53 4.6.1.1 System Language ........................54 4.6.1.2 System Date .......................... 54 4.6.1.3 System Time .......................... 54 14 ESM-RPLC User’s Manual...
Page 15
Security ............................79 4.6.4.1 Secure Boot ........................... 80 4.6.5 Boot .............................. 80 4.6.6 Save and Exit ..........................81 4.6.6.1 Save Changes and Reset ...................... 81 4.6.6.2 Discard Changes and Reset ....................81 4.6.6.3 Restore Defaults ........................81 ESM-RPLC User’s Manual 15...
1.2 Packing List Before installation, please ensure all the items listed in the following table are included in the package. Item Description Q’ty ESM-RPLC COMe Module Desiccant (5g) Screws ESM-RPLC User’s Manual 17...
We strongly recommend that you study this manual carefully before attempting to set up ESM-RPLC or change the standard configurations. Whilst all the necessary information is available in this manual we would recommend that unless you are confident, you contact your supplier for guidance.
Intel® Gfx Up to 96 EU 3 x DDI, VGA, eDP/LVDS (BOM Optional) VGA Supported by Build Option Via DP-to-VGA IC, Max. Resolution Spec. & Resolution 1920x1200@60Hz LVDS Single/Dual Channel 18/24-bit LVDS from eDP-to-LVDS IC, Max. ESM-RPLC User’s Manual 19...
Page 20
Fill with testing condition & standard Example: Random Vibration Operation Reference IEC60068-2-64 Testing procedures Vibration Test Reference ISTA 2A, Method : IEC-60068-2-32 Test:EdSine Vibration test (Non-operation) 1 Test PSD : 0.00454G²/Hz , 1.5 Grms 2 Test frequency : 5~500 Hz 20 ESM-RPLC User’s Manual...
Page 21
2 Test high : 96.5 cm 3 Package weight : 0.2 kg 4 Test drawing Windows 10 IoT Enterprise 2021 LTSC, OS Information Ubuntu 22.04 (Kernel 5.15) above Note: Specifications are subject to change without notice. ESM-RPLC User’s Manual 21...
ESM-RPLC User’s Manual 1.5 Architecture Overview—Block Diagram The following block diagram shows the architecture and main components of ESM-RPLC. 22 ESM-RPLC User’s Manual...
*Default 2.3.1.1 Signal Description –AT/ATX mode selection AT/ATX mode Description AT mode Auto power on, no need to press Power button to enable power on/off ATX mode Press the ATX power button to enable power on/off 26 ESM-RPLC User’s Manual...
PCI Express Differential Receive Pair 0-5 2.3.4.1.4 Flat Panel LVDS Signals Signal Signal Description LVDS_BKLT_CTRL Controls panel digital power. LVDS_I2C_CK I2C clock output for LVDS display use. LVDS_I2C_DAT I2C data line for LVDS display use. LVDS_VDD_EN LVDS panel power enables. 32 ESM-RPLC User’s Manual...
Page 33
Signal Description SUS_S3# Indicates system is in Suspend to RAM state. Active low output. BATLOW# Indicates that external battery is low PWRBTN# Power button to bring system out of S5 (soft off), active on rising edge. ESM-RPLC User’s Manual 33...
Page 34
General purpose I2C port data I/O line. 2.3.4.1.11 USB3.0 Signals Signal Signal Description USB_SSTX[0:1]+ Additional transmit signal differential pairs for the SuperSpeed USB data path. USB_SSTX[0:1]- USB_SSRX[0:1]+ Additional receive signal differential pairs for the SuperSpeed USB data path. USB_SSRX[0:1]- 34 ESM-RPLC User’s Manual...
DP AUX+function if DDI[1:3]_DDC_AUX_SEL is no connect DDI[1:3]_CTRLCLK_AUX+ HDMI/DVI 12C CTRLCLK if DDI[1:3]_DDC_AUX_SEL is pulled high DP AUX-function if DDI[1:3]_DDC_AUX_SEL is no connect DDI[1:3]_CTRLDATA_AUX- HDMI/DVI 12C CTRLDATA if DDI[1:3]_DDC_AUX_SEL is pulled high DDI[1:3]_HPD Digital Display Interface Hot-Plug Detect ESM-RPLC User’s Manual 39...
2.4 Installing Heatsink / Cooler Standard Temperature Heat spreader Cooler (ACC-ESMRPLC-CL-1R) for the SKUs of ESM-RPLC with 13th Gen. Intel® P-Series (28 W) and U-Series (15W). Step1. Using 4 screws (M2.5-18L) to lock the heat spreader and Cooler through PCB screw holes from top to bottom.
Enter to find all the relevant software, utilities, and documentation. Note: Installation procedures and screen shots in this section are for your reference and may not be exactly the same as shown on your screen. 42 ESM-RPLC User’s Manual...
Windows 10 operation system. If the warning message appears while the installation process, click Continue to go on. Step 3. Click Install. Step1. Click Next. Step 4. Click Finish to complete setup. Step 2. Click Accept. ESM-RPLC User’s Manual 43...
Note: The installation procedures and screen shots in this section are based on Windows 10 operation system. Step 3. Click Start. Step 1. Click Begin installation. Step 4. Click Finish to complete setup. Step 2. Click I agree. 44 ESM-RPLC User’s Manual...
All drivers can be found on the Avalue Official Website: www.avalue.com. Note: The installation procedures and screen shots in this section are based on Windows 10 operation system. Step 1. Click OK to continue installation. Step 2. Setup completed. ESM-RPLC User’s Manual 45...
Note: The installation procedures and screen shots in this section are based on Windows 10 operation system. Step 3. Click Next. Step 1. Click Next to continue installation. Step 4. Click Finish to complete setup. Step 2. Click Next. 46 ESM-RPLC User’s Manual...
Note: The installation procedures and screen shots in this section are based on Windows 10 operation system. Step 3. Click Next. Step 1. Click Next to continue installation. Step 4. Click Next. Step 2. Click Next. Step 5. Setup completed. 48 ESM-RPLC User’s Manual...
If the message disappears before you respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the "RESET" button on the system case. You may also restart by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys. 50 ESM-RPLC User’s Manual...
Note: Some of the navigation keys differ from one screen to another. • To Display a Sub Menu Use the arrow keys to move the cursor to the sub menu you want. Then press <Enter>. A “➢” pointer marks all sub menus. ESM-RPLC User’s Manual 51...
BIOS Vendor and your systems manufacturer to provide the absolute maximum performance and reliability. Even a seemingly small change to the chipset setup has the potential for causing you to use the override. 52 ESM-RPLC User’s Manual...
<Enter> to accept and enter the sub-menu. 4.6.1 Main Menu This section allows you to record some basic hardware configurations in your computer and set the system clock. ESM-RPLC User’s Manual 53...
Note: The BIOS setup screens shown in this chapter are for reference purposes only, and may not exactly match what you see on your screen. Visit the Avalue website (www.avalue.com) to download the latest product and BIOS information. 54 ESM-RPLC User’s Manual...
Use the CPU configuration menu to view detailed CPU specification and configure the CPU. Item Options Description Intel (VMX) Virtualization Disabled When enabled, a VMM can utilize the additional Technology Enabled[Default] hardware capabilities provided by Vanderpool ESM-RPLC User’s Manual 55...
All[Default] Number of E-cores to enable in each processor package. Note: Number of Cores and E-cores are Active Efficient-cores looked at together. When both are {0,0}, Pcode will enable all cores. 4.6.2.1.1 Efficient-core Information 56 ESM-RPLC User’s Manual...
Speed Step or Intel Speed Shift to be available and Disabled enabled). Enabled[Default], C States Enable/Disable CPU Power Management. Disabled Enabled[Default], Enable/Disable C1E. When enabled, CPU will switch Enhanced C-States Disabled to minimum speed when all cores enter C-State. 58 ESM-RPLC User’s Manual...
Option Description Disabled When Disabled ME will be put into ME Temporarily ME State Enabled[Default], Disabled Mode. 4.6.2.3.1 Firmware Update Configuration Item Option Description Disabled[Default], ME FW Image Re-Flash Enable/Disable Me FW Image Re-Flash function. Enabled ESM-RPLC User’s Manual 59...
Enable[Default] and INT1A interface will not be available. 4.6.2.5 APCI Settings Item Options Description Enables or Disables System ability to Disabled Hibernate (OS/S4 Sleep State). This Enable Hibernation Enabled[Default], option may not be effective with some 60 ESM-RPLC User’s Manual...
4.6.2.6.1 ~ 4.6.2.6.2 for more information. Item Description Serial Port 1 Configuration Set Parameters of Serial Port 1 (COMA). Serial Port 2 Configuration Set Parameters of Serial Port 2 (COMB). 4.6.2.6.1 Serial Port 1 Configuration ESM-RPLC User’s Manual 61...
Item Option Description Enabled[Default], Serial Port Enable or Disable Serial Port (COM). Disabled 4.6.2.6.2 Serial Port 2 Configuration Item Option Description Enabled[Default], Serial Port Enable or Disable Serial Port (COM). Disabled 4.6.2.7 EC 5782 HW Monitor 62 ESM-RPLC User’s Manual...
Enable or disable System wake on alarm event. Select Disabled[Default], Fixed Time, system will wake on the hr::min::sec specified. Wake system from S5 Fixed Time Select Dynamic Time, System will wake on the current time Dynamic Time + Increase minute(s). ESM-RPLC User’s Manual 63...
Page 64
Select Fixed Time, system will wake on Wake system from S5 Fixed Time the hr::min::sec specified. Select Dynamic Dynamic Time[Default] Times, System will wake on the current time + Increase minute(s). Wake up minute increase 1-5. 64 ESM-RPLC User’s Manual...
Console Redirection EMS Console Redirection Enable or Disable. Enabled 4.6.2.9.1 COM0 Item Option Description VT100 Emulation: ANSI: Extender ASCII char set. Terminal Type VT100+ VT100: ASCII char set. VT100+:Extends VT-UTF8 VT100 to support color, function keys, etc. ESM-RPLC User’s Manual 65...
Page 66
With this mode enabled only text will be sent. Recorder Mode Enabled This is to capture Terminal data. Disabled[Default] Enables or disables extended terminal Resolution 100x31 Enabled resolution. VT100[Default] Intel Linux XTERMR6 Putty KeyPad Select FunctionKey and KeyPad on Putty. ESCN VT400 66 ESM-RPLC User’s Manual...
Legacy OS and Legacy OPROM Messages. 4.6.2.9.3 Console Redirection EMS Item Option Description Microsoft Windows Emergency Management Services (EMS) allows for remote Out-of-Band Mgmt Port COM0[Default], management of a Windows Server OS through a serial port. ESM-RPLC User’s Manual 67...
20 sec[Default] USB mass storage device Start Unit command Device reset time-out 30 sec time-out. 40 sec Auto[Default] Maximum time the device will take before it Device power-up delay Manual properly reports itself to the Host Controller. 68 ESM-RPLC User’s Manual...
Optical drives are emulated as ‘CDROM’, drives with no media will be Hard Disk CD-ROM emulated according to a drive type. 4.6.2.11 Network Stack Configuration Item Options Description Enabled Network Stack Enable/Disable UEFI Network Stack. Disabled[Default] ESM-RPLC User’s Manual 69...
HTTP boot option will not be created. Wait time to press ESC key to abort the PXE PXE boot wait time boot. Number of times presence of media will be Media detect count checked. 4.6.2.12 NVMe Configuration 70 ESM-RPLC User’s Manual...
State Drive or Hard Disk Drive. Enabled[Default] Port 1 Enable or Disable SATA Port. Disabled Hard Disk Drive Identify the SATA port is connected to Solid SATA Device Type Solid State Drive[Default] State Drive or Hard Disk Drive. 76 ESM-RPLC User’s Manual...
4.6.3.3 Board & Panel Configuration Item Option Description VBT Selection VBT0 – eDP/LVDS, VGA, 3 VBT0[Default] DP++ VBT2 – VGA, 3 HDMI Note. If you VBT Selection VBT2 disable VGA, VGA will not show any more. ESM-RPLC User’s Manual 77...
Page 78
Off[Default] PWR-On After PWR-Fail AC loss resume. Last state Disabled Wake Up by LAN Wake Up by LAN from S3/S4/S5. Enabled[Default] Disabled[Default] 30 sec 40 sec Watch Dog Select WatchDog. 50 sec 1 min 2 min 78 ESM-RPLC User’s Manual...
User’s Manual 10 min 30 min Disabled[Default] 7-bit address of SPB1002 Disabled(No I2C0 Test device CTB-20 Enabled Device) Enabled(NCT5655, 0*20) 4.6.3.3.1 SHOW DMI INFO 4.6.4 Security ESM-RPLC User’s Manual 79...
The setup program then exits and reboots the controller. 4.6.6.3 Restore Defaults This option restores all BIOS settings to the factory default. This option is useful if the controller exhibits unpredictable behavior due to an incorrect or inappropriate BIOS setting. ESM-RPLC User’s Manual 81...
Page 82
Attempts to Launch EFI Shell application (Shellx64.efi) from one of the available filesystem devices. 4.6.6.5 Expert mode [DQV mode] Switch Expert mode or DQV mode. Configuration options: [DQV mode] [Expert mode] 4.6.7 MEBx ⚫ Intel® ME Password MEBx Login. 82 ESM-RPLC User’s Manual...