Page 1
Culligan Water Tower ™ Drinking Water System Owners Guide...
Page 2
Check with your public works department for applicable local plumbing and sanitation codes. Follow your local codes if they differ from the standards used in this manual. Operational, maintenance and replacement requirements are essential for this product to per- form properly. The Culligan Water Tower contains replaceable particulate and activated carbon ™...
Table of Contents Safety/Warnings ... i System Specifications ... 2 Introduction About Your System ... 3 System Component Description ... 3 Application Guidelines ... 4 Certified Performance ... 5 Installation ... 6 Servicing Your System ... 7 Cartridge Replacement, Cleaning and Sanitizing Procedure ... 8 Troubleshooting Guide ...
With the Culligan Water Tower drinking water system, you’ll get a continuous supply of clear, refreshing water for drinking and cooking. But Culligan improves a lot more than just water.
Application Guidelines The Culligan Water Tower drinking water system is designed for use on potable water supplies meeting the guidelines outlined in Table 1. The system should be installed on your home’s cold water line.
Table 1 Influent Water Characteristics Pressure Temperature Total Dissolved Solids (TDS) Chlorine Chloramine Turbidity Silt Density Index (SDI) Hardness (CaCO Hydrogen Sulfide (H Manganese (Mn) Iron Bacterial Quality A pressure regulator is recommended for feed water pressures exceeding 80 psig (552 kPa) See the Technical Manual for all applications where TDS exceeds 1000 ppm (1000 mg/L) to calculate effective module pressure.
Installation This Owner’s Guide provides visual assembly reference only (Figure 2). Since specialized skills are required in the assembly of the drinking water system, we recommend that you contact your local independently operated Culligan dealer to complete this installation. ®...
Cartridge Replacement Culligan recommends that you have your Culligan Water Tower drinking water system serviced by your local Culligan Man . You can rely on his or her experience and expertise to keep your ™...
If you wish to service your system, the filters are available from your Culligan dealer. See the Parts List at the end of this section for replacement numbers. Cartridge Conditioning The activated carbon, reverse osmosis, and polishing filter cartridges must be conditioned as...
Page 11
3. Check product water storage tank air pre-charge using low-pressure gauge (PN 34002024). Air valve is located on tank base. Pre-charge should be 55 kPa (8 psig) with tank empty and tank valve open. Note: Use hand pump to avoid damaging tank. Verify product water faucet is open before proceeding.
Page 12
9. Clean filter housings/manifold, inside and outside, with washcloth and cleaning 10. Rinse housings/manifold with clean potable water. 11. Inspect filter housing O-ring groove and manifold O-ring surface for damage such as 12. Place a small amount of O-ring lubricant on surface of filter housing O-ring. Install TO SANITIZE THE SYSTEM: Complete Steps 13-33.
Page 13
CAUTION: Wear safety glasses while performing this procedure. CAUTION: Read “WARNINGS” information on bleach container before using contents. Handle sanitizing solution carefully. Avoid contact with unprotected areas. 13. Mix sanitizing solution of 1.5 ml (1/3 teaspoon) of household bleach and 3.8 L (1 gallon) of clean, potable water in the bucket.
Page 14
21. Install cartridges. (Refer to Figure 5 for location of each cartridge). Note: Tighten filter housings by hand only. Do not use tools as they will over-tighten and damage housings. Take care not to cut or pinch the O-rings. 22. Turn feed water valve slowly to open position. 23.
Page 15
Note: Replace battery with a new alkaline 9-volt battery (PN 31300001) 26. Carefully slide battery into its holder. 27. Connect battery by pressing clip onto battery terminals. 28. Test monitor connection by activating monitor. Open product water faucet. If an indicator light illuminates, connection is good.
Replace pre-filter cartridge(s) Empty water from storage tank (product water faucet must remain open while adjusting pressure) and adjust pressure to 55 kPa (8 psig) Contact your Culligan Dealer ® Replace flow control (Item 6) in parts list and contact your...
Page 17
O-ring groove for debris. Clean groove, lube and reseat O-ring Replace O-ring Clear restriction Re-route tubing so tubing runs vertically with no sharp bends or loops Action None Call your Culligan Replace membrane Plug connector into phone jack Replace battery Connect battery dealer ®...
Culligan Water Tower Service Log ™ Model Serial No. Date Installed — For Service Call Culligan at: Cartridge(s) Changed Activated Activated Date Sediment Pre-Carbon Post-Carbon Serviced Filter Filter Membrane Filter Sanitized...
Any part found defective within the terms of this warranty will be repaired or replaced by the dealer. If any part is found defective, Culligan also reserves the right to replace the drinking water appliance with a comparable Culligan drinking water system of equal or greater quality.
Page 21
Materials & description: 8-1/2 x 11, 20 page book, saddle stitched, three hole punched - Prints black ink on 50# offset white This page contains materials and DCO information. IT DOES NOT PRINT AS PART OF THE DOCUMENT! CHANGE DCO 1254 APRVD DATE 8/21/00...