Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Asus ROG Strix G13CH
Summary of Contents for Asus ROG Strix G13CH
- Page 1 Desktop ROG Strix G13CH Service Manual...
- Page 2 INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR INTHIS MANUAL OR PRODUCT.
- Page 3 ASUS will only be responsible for or indemnify you for loss, damages or claims based in contract, tort or infringement under this Warranty Statement. This limit also applies to ASUS' suppliers and its reseller. It is the maximum for which ASUS, its suppliers, and your reseller are collectively responsible.
-
Page 4: Table Of Contents
Table of Contents ASUS Desktop ROG Strix G13CH Overview Components Top View Components Bottom View Appropriate Tools Disassembly steps : • SLIDE DOOR • VGA CARD • • SPRING SCREW COOLER • 9CM SYS FAN •... -
Page 5: Asus Desktop Rog Strix G13Ch Overview
❻ LAN (RJ-45) port ❼ Wi-Fi ports ❽ Microphone port (pink) ❾ Line Out port (lime) ❿ Line in port (light blue) ⓫ Power connector ⓬ Expansion slot brackets ⓭ ASUS Graphics CARDs (on selected models only) ⓮ Air vents Back... -
Page 6: Components Top View
Components Top View ♦ VGA CARD ♦ M2 PAD 25X20X7 ♦ HDD ♦ MAIN BOARD ♦ USB CABLE ACETATE TAPE ♦ POWER SW CABLE ♦ RFCABLE ASSEMBLY SMA ♦ SHIELDING FOR Z690 WIFI (RTX3070-8GD6) ♦ FRONT IO BD (PH-RTX3050-8G, PH-RTX3060-12G) ♦... -
Page 7: Components Bottom View
Components Bottom View ♦ LED BD UP ♦ PD500TC M2 SSD SINK ♦ MAIN BOARD ♦ LED BD DOWN COOLER BACK PLATE ♦ G16CH M2 SSD SINK ♦ LED CR BD ♦ SPRING SCREW COOLER ♦ POWER SWITCH HOLDER ♦ SIDEDOWN LED BD ♦... -
Page 8: Appropriate Tools
Appropriate Tools Please prepare and select the appropriate tools to disassemble/assemble for the ROG Strix (G13CH) desktop. ♦ Screwdriver ♦ Alcohol 95% ♦ Glove ♦ Dust-free Cloth Please accord to different screw specification to choose different screwdriver and head. #1 #2 ♦... -
Page 9: Slide Door
SLIDE DOOR Disassembly Notice Please be sure to pull out AC POWER CORD. Step 1 : Remove screws *4pcs. Screws Spec Torque (kgf-cm) Step 2 : Pull the side doors *2pcs. SCREW #6-32*6.3L (7.3,2.45) 8.0±0.5 Pull SLIDE DOOR (L) Pull SLIDE DOOR (R) Back... - Page 10 SLIDE DOOR Assembly Notice Please follow the instructions below to assemble SPNL SCREW and SIDE DOOR PLATE SHADOW BLACK. SPNL SCREW PACKAGE SIDE DOOR PLATE SHADOW BLACK Step-3 Assemble screws*4pcs. Step-1 Assemble screws*4pcs. Step-2 Assemble SIDE DOOR PLATE SHADOW BLACK to CHASSIS...
-
Page 11: Vga Card
VGA CARD Disassembly Notice Please be sure to pull out AC POWER CORD. Screws Spec Torque(kgf-cm) Step 1 : Disconnect cable (Yellow mark). SCREW M3*4L (6.3,2.05) (B) #2 6.0±0.5 Step 2 : Open the case and remove screws *4pcs (Red and Blue mark). Step 3 : Press and unlock the VGA CARD (Green mark). - Page 12 VGA CARD Assembly Notice Please follow the below steps to assemble PH-RTX3050-8G, PH-RTX3060-12G VGA CARD. Step-1 Assemble the VGA BKT SLOT1 on the side of the VGA CARD. Step-2 Assemble the STAND OFF on the MB. VGA BKT SLOT1 PH-RTX3050-8G, PH-RTX3060-12G VGA CARD STAND OFF #6- 32*12H*5D...
-
Page 13: Ddr
Disassembly Notice Please be sure to pull out AC POWER CORD. Step 1 : Press down and unlock DDR, then remove DDR *4pcs. Press down and unlock (*4pcs) Assembly Notice Please follow the below order to use DDR slot. (DDR *1pc) (DDR *2pcs) (DDR *3pcs) Back... -
Page 14: Spring Screw Cooler
SPRING SCREW COOLER Disassembly Notice Please be sure to pull out AC POWER CORD. Step 1 : Release 4 screws (green mark) holding on the SPRING SCREW COOLER, then disconnect the cable connector(red mark). Step 2 : Take out SPRING SCREW COOLER. Release and disconnect Take out SPRING SCREW COOLER... -
Page 15: 9Cm Sys Fan
9CM SYS FAN Disassembly Notice Please be sure to pull out AC POWER CORD. Step 1 : Disconnect FAN connector *1pc. (yellow mark) Screws Spec Torque (kgf-cm) Step 2 : Remove screws *4pcs on the outside of iron grid. M5*10L (K) B-NI TAPPING 8.0±0.5 Step 3 : Take out the Fan *1pc. -
Page 16: Front Bezel And Led Board
FRONT BEZEL AND LED BOARD Disassembly Notice Please be sure to pull out AC POWER CORD. Step 1 : Pull the latch (green mark) to release and open FRONT BEZEL. Screws Spec Torque (kgf-cm) Step 2 : Disconnect the (yellow mark) connectors and remove FRONT BEZEL . Step 3 : Remove screws *7pcs then remove LED COVER. - Page 17 LED CR BD for (Metal side door) only Assembly Notice Before assemble cable on LED CR BD, please follow below steps to paste PINHEADER ACETATE FABRIC. Spec G35CA PINHEADER ACETATE FABRIC Step1-1 : PIN HEADER cannot exceed ACETATE FABRIC. Step2 : Take another ACETATE FABRIC and align it with the first ACETATE Step1-2 : Align the FPC CONNECTOR and the white wire with the ACETATE FABRIC.
- Page 18 4D(Plastic side door) Cable for 2D(Metal side door) and only Assembly Notice Before assemble two cables, please follow below to paste ACETATE TAPE. Spec G15DK USB CABLE ACETATE TAPE Note: The two cables are GL10DH SATA CABLE 15P F/P 430MM and CABLE USB2.0 CRB TO Step1-1 : Winding the two cables with ACETATE TAPE to increase the insulation layer.
-
Page 19: Top Cover
TOP COVER Disassembly Notice Please be sure to pull out AC POWER CORD. Step 1 : Remove screws *2pcs. Screws Spec Torque (kgf-cm) Step 2 : Pull the latch to release and remove TOP COVER. SCREW #6-32*6L(7.1,2.3) (B) #2 8.0±0.5 Remove Pull the Latch (green mark) Assembly Notice... -
Page 20: Cpu Fan 12Cm
CPU FAN 12CM Disassembly Notice Please be sure to pull out AC POWER CORD. Step 1 : Disconnect (yellow mark) FAN connector *1pc. Screws Spec Torque (kgf-cm) Step 2 : Remove screws *4pcs on the outside of iron grid. M5*10L (K) B-NI TAPPING 8.0±0.5 Step 3 : Take out the Fan*1 pcs. -
Page 21: Front Io Board
FRONT IO BOARD Disassembly Notice Please be sure to pull out AC POWER CORD. Step 1 : Remove screws *4pcs.(Red and green mark) Screws Spec Torque (kgf-cm) Step 2 : Flip up the bracket and remove screw *1pc, then separate the FRONT IO BOARD and bracket. #6-32*6L(7.1,2.3) (B) #2 8.0±0.5 Step 3 : Disconnect Audio cable, remove tape from FIO USB CABLE(USB3.0) cable connector, then disconnect it. - Page 22 NEW FRONT IO BOARD Assembly Notice Please follow the below steps to assemble FRONT IO BOARD. Step-1 FIO bracket and small card, corresponding hole assembly. Step-2 Assemble the STAND OFF on the MB. Step-3 Assemble the cables*3pcs. POWER AUDIO SCREW M3*4L (6.3,2.05) (B) #2*3pcs Step-4 Assemble the USB3.0 CABLE on the MB.
- Page 23 FRONT IO BOARD Assembly Notice Please follow the below image to assemble NEW/OLD FRONT IO BOARD. Step-1 If you use the NEW FRONT IO BOARD CABLE USB2.0 FRONT BEZEL CRB TO MB AUDIO CABLE SIDE LED CABLE NEW FRONT IO BOARD use CABLE USB3.0 FIO TO MB L600 Step-2 If you use the OLD FRONT IO BOARD FRONT BEZEL CABLE USB2.0...
-
Page 24: Ssd
Please be sure to pull out AC POWER CORD. Disassembly Notice Screws Spec Torque (kgf-cm) G16CH SSD HEAR SINK(WITH SCREW) 2.0±0.2 Step 1 : (SSD1) Release screws *2pcs and take out the SSD HEAR SINK. Step 2 : (SSD1) Remove SSD *1pc. PD500TC M2 SSD SINK(WITH SCREW) (M2*0.4,L=5mm) 2.0±0.2 Step 3 : (SSD2) Remove screws *2pcs and take out the M2 SSD SINK. -
Page 25: Main Board & Cpu
MAIN BOARD & CPU Disassembly Notice Please be sure to pull out AC POWER CORD. Screws Spec Torque (kgf-cm) Step 1 : Disconnect (yellow mark) connectors *6pcs. 8.0 ± 0.5 M3*4L (6.3,2.05) (B) #2 Step 2 : Remove screws *8pcs (Red and green mark). Step 3 : Take out the Main Board. - Page 26 MAIN BOARD Assembly Notice Please follow the below image to Add sponge *4pcs (red mark)on motherboard DIMM Area. D700TD MB SPONGE L35 W8 T8//L35 W8 T8...
-
Page 27: Wlan Card
WLAN CARD Disassembly Notice Please be sure to pull out AC POWER CORD. Step 1 : Remove screws *2pcs and take out SHIELDING FOR Z690 WIFI with WLAN CARD. Screws Spec Torque (kgf-cm) Step 2 : Remove screw *1pc and SHIELDING FOR Z690 WIFI. Step 3 : Disconnect RF cables*2pcs, remove screw *1pc and WLAN CARD. -
Page 28: Power Switch
POWER SWITCH Disassembly Notice Please be sure to pull out AC POWER CORD. Assembly Notice When need to reuse old POWER SWITCH HOLDER, please Step 1 : Push hooks then take out POWER SW CABLE with POWER SWITCH HOLDER from CHASSIS. make sure the hooks no broken or deformation. -
Page 29: Hdd & Io Shielding
HDD & IO SHIELDING Disassembly Notice Please be sure to pull out AC POWER CORD. Step 1 : Remove screws *4pcs. Screws Spec Torque (kgf-cm) Step 2 : Disconnect the connectors *2pcs Step 3 : Take out the HDD and cable. SCREW #6-32*6.3L (7.3,2.45)(B) B-ZN #2 6.5±0.5 Step 4 : Press and push the IO SHIELDING to remove it. -
Page 30: Power Supply
POWER SUPPLY Disassembly Notice Please be sure to pull out AC POWER CORD. Step 1 : Cut the cable ties *7pcs. Screws Spec Torque (kgf-cm) Step 2 : Remove screws *4pcs. SCREW #6-32*6.3L (7.3,2.45)(B) B-ZN #2 Step 3 : Disconnect the connector *1pc & take out the POWER SUPPLY. 8.0±0.5 Disconnect Unscrew... -
Page 31: Led Board
LED BOARD Disassembly Notice Please be sure to pull out AC POWER CORD. Screws Spec Torque (kgf-cm) Step 1 : Remove screws *2pcs and then disconnect cables *2pcs. SCREW M2.5*4L (K) B-ZN NY 2.5±0.2 Step 2 : Remove screws *3pcs and then disconnect cable *1pc. SCREW M2.5*4L (K) B-ZN NY 2.5±0.2 Unscrew (red mark) -
Page 32: Cable Assembly
CABLE ASSEMBLY Assembly Notice Please according to below image to Tidy up the cables. Back...