Table of Contents
Advertisement
1-4.
CCTV OPERATION
A. VIDEO OUTPUT
Step 1. Connect
the monitor(s)
to the camera
using
RG-59U
cable or equivalent
and a male UHF
connector
(PL-259) at the UHF
connector on
the rear panel of the camera.
Make
sure that
the
equipment
fed by the camera
terminates
the feed cable in 75 ohms.
Step 2. Set the selector switch to VIDEO.
Follow Steps 3, 4, 6, 7 and 8 in the previous
section.
B. R-F OUTPUT
This mode
of operation permits conventional
TV sets to be used as monitors.
Step 1. Connect the r-f output cable to the UHF con-
nector
on
the
rear
of the
camera
using
a
RG-59U
cable or equivalent,
equipped with a
male UHF connector (PL-259).
Step 2. The other end of the cable should be equipped
with a BALUN
(72 ohm — 300 ohm transformer)
to permit connection
to the 300—ohm
antenna
terminals on the TV set.
_ Step 3. Set the selector switch on the camera
to the
RF position.
Step 4. Set the channel selector on the TV set to an
inactive channel between 2, 3 or 4.
Step 5. Follow Steps 3 and 4 in Section 1-3 to power
the camera. Turn the power switch to ON.
HORIZ
SYNC.
INPUT (15.75KHz)*
MORE
THAN
2V(P— P)
a
MORE. THAN
2V(P— P)
VERTICAL
SYNC
INPUT(60Hz) *
6-PIN
VTR
OUT
PANEL
JACK(REAR
VIEW)
Step 6. Using a smal] screwdriver,
turn the RF con-
trol in the rear panel of the camera
until the
picture appears
on the screen of the monitor.
Adjust
for best resolution without overshoot.
Note, if a blank, noise-free raster is obtained,
check
the lens
cap,
power
switch
and lens
opening to make sure that the video portion of
the camera is fully operational.
1-5. CONNECTIONS
Figure 1-1 shows sync input and video output signals
at the 6-pin VTR connector
when
the camera is used
in the VTR mode. (Sync signals appear only when the
motor in the VTR
is running).
1-6. VIEWFINDER CVF-4
To connect
the Viewfinder,
first remove
the rectangu-
lar plastic cap that covers
the viewfinder connector
on the top surface of the camera. Place the Viewfinder
atop the camera
so that the two studs at the rear of
the camera enter the large holes in the mounting slots
on the bottom of the Viewfinder. Slide the Viewfinder
towards
the rear of the camera
so that the studs en-
gage
the slots.
Position
the male
connector
on the
bottom
of the Viewfinder
over the receptacle
on the
top of the camera and push down gently until the con-
nector is seated. Pushthe mounting screw down
and
tighten using a coin or screwdriver.
Note.
All electrical
connections
between
the View-
finder
and the camera
are completed
at the mating
connectors. The raster on the Viewfinder will appear
immediately when the camera
is turned on. The pic-
ture
appears
a few seconds
later when
the vidicon
warms
up. Contrast and brightness controls atop the
CVF-4 affect the Viewfinder picture only, and do not
affect the video output of the camera.
fit
1.7V
oe
VIDEO
OUTPUT
(60Hz)
0.45— 0.50V
*SYNC
SIGNALS
FROM
THE
VTR(MOTOR
RUNNING)
FIG. |-1. INPUT
AND
OUTPUT
SIGNALS
AT
THE
6-PIN
VTR
CONNECTOR.
1-2
Advertisement
Table of Contents
