Advertisement
3.5 START UP AND CHOICE OF SPEED
The electronic variation system provides the user with a wide
range of variable speeds.
• Start the beater by turning button G from the stop position O to
the position between 1 and 12 according to the speed at which
the appliance is to operate.
3.6 FITTING/REMOVING THE SAFETY GUARD
• To remove the guard:
1) Raise the safety guard to its upper stop.
2) Using your 2 index fingers, push on the two rods J of the safety
guard with your thumbs applied against the pivot axis of the guard.
Never assemble the guard in a different position than that shown
on this manual.
3.7 ACCESSORIES HUB
• This beater is fitted with a variable speed accessories hub (square
dimension 12 mm, type K) to drive the optional accessories:
3.
3.
7a
• To fit one of the accessories, proceed as follows:
- The beater must be stopped.
- Fit the accessory which corresponds to the work to be carried
out.
- Turn the cover L.
- Position the accessory and insert the conical endpiece N of
accessory P into the accessories hub M of the beater.
- Engage the square S into the drive shaft of the hub M by pivoting
accessory P.
- Position the pin R into the groove (T) and drive the accessory
home into the hub M.
- Tighten the lock screw U (clockwise
- Recommendations for using the meat mincer
- Prepare the meat before inserting it into the mincer:
- Remove all bones and gristle.
- Cut the meat into long, thin pieces (about the same size
as your thumb).
- Put part of the meat in the cup of the mincer.
Cleaning and hygiene
4.1 IN BETWEEN USE
• Remove the bowl, tool and guard.
• Using hot water and detergent - disinfectant, immerse and wash
the inside of the bowl, tool and guard, then rinse in clean water
and dry.
4.2 AFTER USE
• Unplug the machine.
• Remove the bowl, tool and guard.
• Clean the bowl, tools and guard by immersing them in hot water
and detergent - disinfectant then rinse in clean water and dry.
The bowl and tools can be washed in a dishwasher.
• Clean the planetary gear, tool holder shaft and cradle paying
particular attention to the bowl handles and the outside of the
whisk if necessary using a damp sponge and a detergent product,
then rinse.
• Check that the different parts have been cleaned correctly.
Electromix 5 GB 11 2023
3.
6a
7b
).
3.
4 a -b -c
3.
4 a -b -c
3.
3.
1
3
• Always start in slow speed 1 to avoid splashing or clouds of
flour, and then progressively increase the speed.
V
Speed of planetary gears (rpm)
S D Soft dough
H D Hard dough
Normal range recommended.
• To fit the guard:
1) Engage the 2 rods J of the guard in the rotating shaft K.
2) Using your thumbs, press down on the lower part of the safety
guard rods, applied against the pivot axis of the guard.
1.
2.
1a
- Start up the beater by positioning button G between 7 and 9.
- Slide the pieces of meat into the chute one at a time. They
will get caught by the screw.
- Use the pusher (and only the pusher) if the piece of meat
does not get taken up by the screw. Do not fill up the chute
and subsequently force with the pusher as this does not
accelerate the mincing process but damages the machine.
Note: Using the mincer heats up the motor and the thermal safety
device could cut out the appliance. In this case, you must wait for
a few minutes for the motor to cool down before starting
the appliance back up.
To prevent sudden heating up, you are advised to follow
the instructions given above. The operating time is
approximately 8 to 10 minutes which corresponds to processing
roughly 3 kg of meat.
These optional accessories are designed to perform ac-
companying work and not industrial quantities. Heavy duty
and forced use would damage your beater.
The machine must be stopped, before fitting or
removing an accessory.
3
.6a - b
• Clean the planetary gear housing, tool holder spindle and guard
with a damp sponge and a detergent - disinfectant.
Note: use cleaning products that are compatible with
the aluminium and plastic parts.
3
.6a - b
Note: Check that the products used for cleaning are
compatible with the machine equipment.
• Do not use abrasive detergents, which could scratch the surfaces.
Never clean the machine with a hose or high pressure cleaner
Do not put the machine in the dishwasher.
Periodically: (at least once a month)
• Wipe and lightly grease the lifting and lowering pins with Vaseline
and the pins of the guard.
4
3.
1
4c
3.
6b
Advertisement
