Siemens SN536S01KE Quick Reference Manual

en
Short and handy...
... everything your dishwasher needs.
Before using for the first time, make sure you read both the op-
erating and the installation instructions.
How to use your appliance
Load the tableware.
1.
Only clean tableware that is suitable for dish-
washers. Remove large remnants of food from
the tableware. Check that the spray arms can ro-
Overview of water hardness settings
You can find an overview of the
water hardness values that can
be selected here.
A table of country-specific units
can be found in the instruction
manual.
Hardness mmol/l Setting
range value
Soft 0 - 1.1 H00
Soft 1.2 - 1.4 H01
Adding special salt
To avoid damage to the appliance, only add special
salt to the dispenser for special salt just before the
programme starts.
Unscrew the lid of the dispenser for special salt
1.
and remove.
On initial start-up: Fill the dispenser right up with
2.
water.
Adding rinse aid
Press the catch on the lid
1.
of the dispenser for rinse
aid and lift ⁠ .
Adding detergent
Add the detergent to the
1.
dry detergent dispenser.
tate freely.
Add detergent.
2.
Switch on the appliance ⁠ .
3.
Setting water softening system
Press
Medium 1.5 - 1.8 H02 1.
Medium 1.9 - 2.1 H03 Hold programme button A and press
2.
repeatedly until the display
Medium 2.2 - 2.9 H04
shows H:xx.
Hard 3.0 - 3.7 H05
3. Release programme button A and
Hard 3.8 - 5.4 H06
⁠ .
Hard 5.5 - 8.9 H07
Programme button A flashes.
a
Press programme button C re-
4.
peatedly until the right water hard-
ness has been set.
5. Press
Add the special salt to the
3.
dispenser. The water in the
dispenser is displaced and
forced out. Never add de-
tergent.
Place the lid back on the dispenser and turn to
4.
close.
Add rinse aid up to the
2.
max mark.
2
1
Close the lid of the dispenser for rinse aid.
3.
The lid clicks into position.
a
Close the lid of the deter-
2.
50 ml
gent dispenser.
25 ml
15 ml
a The lid clicks into position.
Select the programme.
4.
Start the programme ⁠ .
5.
Remove the tableware at the end of the pro-
6.
gramme.
Programs
⁠ . The program data has been meas-
ured in the laboratory according to
European standard EN 60436.
The consumption figures depend on
the program and additional function
selected.
The runtime will change if the rinse
aid system is switched off or rinse aid
needs to be added.
Program
to save the setting.
/
Intensive 70°
/
Auto 45-65°
/
Eco 50°
/
Glass 40°
1 hr Programme
/
PreRinse
max
To cancel the programme, press
7.
approx. 3 seconds.
The programme is cancelled and ends after ap-
prox. 1 minute.
1) Duration [h:min]
2) Energy [kWh]
3) Water [l]
1) 2:05 - 2:15
2) 1,400 - 1450
3) 12 - 15
1) 1:35 - 2:40
2) 0,950 - 1,550
3) 9 - 19
1) 3:30
2) 0,920
3) 9,5
1) 1:25 - 1:30
2) 0,850 - 0,900
3) 11 - 14
1) 1:00
2) 1,300
3) 10
1) 0:15
2) 0,050
3) 4
for