Table of Contents
Advertisement
RX-FS400
RX-FS400
MEASUREMENTS AND ADJUSTMENTS
@ ALIGNMENT INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING ALIGNMENT
1. Set volume control to maximum.
2. Set tone control to TREBLE.
3. Set band switch to AM or FM ST.
5. Set power source voltage to 9 V DC.
6. Output of signal generator should be no higher
than necessary to obtain an output reading.
4. Set function selector to RADIO or TAPE.
@ AM-IF ALIGNMENT
SIGNAL GENERATOR or
— _
SWEEP GENERATOR
RADIO DIAL
SETTING
455 kHz
Point of non-
Fashion a loop of
Ciena | eee:
foe
g
at 400 Hz
the loop ant. of receiver.
600 kHz)
@ AM-RF ALIGNMENT
Fashion a loop of
several turns of wire
511 kHz
and radiate a signal into
the loop ant. of receiver.
fully closed.
1,500 kHz
(*1) Fix antenna coil with wax after completing
—_
@ FM-IF ALIGNMENT
SIGNAL GENERATOR or
SWEEP GENERATOR
RADIO DIAL
SETTING
interference
(on/about
through ceramic
capacitor (0.001 LF)
Negative side to test
90 MHz)
point Suz.
Adjust for maximum
Lf
Lt.
tf!
oe
amplitude. (Refer to Fig. 3.)
@ FM-RF ALIGNMENT
10.7 MHz
(SWEEP)
Tuning capacitor
1.753 kHz
Tuning capacitor
fully open.
INDICATOR
(ELECTRONIC
VOLTMETER or
ADJUSTMENT
REMARKS
OSCILLOSCOPE)
Headphones Jack
(32)
oun dea a nainan | T2(AMIFT)
Adjust for maximum output.
connect the lead wires of
the plug to the measuring
instrument.
L4 (AM OSC
Coil)
CT1
-4 (AM
OSC
"
Trimmer)
Adjust for maximum output.
oe ae
Adjust L3 by moving coil along
the ferrite core.
cm -3
ANT
Adjust for maximum output.
Adjust for maximum output.
INDICATOR
(ELECTRONIC
VOLTMETER or
OSCILLOSCOPE)
ADJUSTMENT
REMARKS
Connect vert. amp.
scope to test point
BiZJ. Negative side
to test point [G2
Adjust for maximum
Connect to test point
through FM
dummy antenna.
Negative side to test
point fiz.
Variable
109.2 MHz
capacitor fully
open.
Variable
capacitor fully
closed.
86.2 MHz
(*2) Three output responses will be present; proper tuning is the center frequency.
Headphones Jack
(32Q)
L2 (FM OSC
(*2) Adjust for maximum
Fabricate the plug as
coil)
output.
shown in Fig. 4. and then
connect the lead wires of
the plug to the measuring
instrument.
CT1-2 (FM OSC
Trimmer)
CT1-1 (FM ANT
Trimmer)
ore
m@ SEPARATION ALIGNMENT
EQUIPMENT
CONNECTION
ELECTRONIC
COUNTER
GGZ3...(+)
bied...(-)
FM SIGNAL GENERTOR
SOURCE CONNECTION
ADJUSTMENT
SPECIFICATION
REMARKS
98 MHz, 60 dB (CW) Connect to
test point
through FM
dummy antenna.
Negative side to §G¥.
Adjust VR1, for 19 KHz +50 Hz reading
on frequency counter.
@ HEAD AZIMUTH ALIGNMENT
EQUIPMENT CONNECTION
TEST TAPE
ELECTRONIC COUNTER
ADJUSTMENT
| SPECIFICATION
_
REMARKS
Headphones Jack (32Q)
fetes the plug shown in Fig. 4. and
(0)
Azimuth screw
(Shown in Fig. 5)
. QZZCFM |
Playback mode.
then connect the lead wires of the plug t
y
the measuring instrument.
@ TAPE SPEED ADJUSTMENT
EQUIPMENT CONNECTION
TEST TAPE
ELECTRONIC COUNTER
ADJUSTMENT
SPECIFICATION
REMARKS
Headphones Jack (32Q)
1. Playback mode.
QZZCWAT
Fabricate the plug shown in Fig. 4. and
Motor VR
3000+70 Hz
2. Adjust motor VR, for 3000+70 Hz
(3 kHz)
(er connect the lead wires of the plug to | | (Shown in Fig. 6)
reading on frequency counter
the measuring instrument.
.
m@ ALIGNMENT POINT
ePlease refer to Circuit Board and Wiring Connection Diagram for test point locations.
FM
OSC
FM ANT
AM ANT
AMIFT
AM ANT
1O9.2MHz
IOGMkH
I5OOkHz
455kHz
600 kHz
AM OSC
\
At
1753 kHz
CTI-4
CT 1-4) WN
y
Fig. 2
"0
UI
FM
ist
iar
10. 7MH
FM
VCO
I9kHz+50Hz
TI
®
%,
®|
@)
AM
OSC
SilikHz
Fig. 3
~
Motor
—- To Measuring
—
Instrument
Azimuth Screw
Fig. 5
Motor VR
Fig. 6
ee eee
Advertisement
Table of Contents
