Husky 90822 Use And Care Manual

USE AND
CARE GUIDE
ADJUSTABLE
SAW HORSE
Warranty
Limited Lifetime Warranty.
If this Husky product ever fails due to a defect in material or workmanship, return the product to any Home Depot retail store for replacement with
an item of equal or greater value. This warranty excludes incidental/inconsequential damages and failures due to misuse, abuse, calibration or
normal wear and tear. This warranty gives you speci c rights, and you may also have other rights, which vary from state to state. Please see store
or call 1-888-HD-HUSKY for details.
Specifications Specifications
Max distributed load 1300 lbs. / 589.7 kg
Operation Operation
1. Unfolding the legs
□ To fully release the rst set of legs, place the sawhorse in the upside-down
position and press the release button (A) labeled "OPEN 1st".
NOTE: To avoid any marring or scratching, place the NOTE: To avoid any marring or scratching, place the
sawhorse on a soft surface. sawhorse on a soft surface.
2. Opening and locking the legs
□ Pull the legs outward to fully extend as shown and push the leg
brace (B) to the locked-out position.
□ Repeat steps 1 and 2 to open the second set of legs.
Item # 1009406865 Item # 1009406865
Model # 90822 Model # 90822
A
B
Operation
3. Turning over to in-use position
□ Ensure that all leg braces (B) are in the locked-out position
and place the sawhorse into the upright position. Also
ensure that all four feet are on a level surface when in use.
4. Adjusting height and support arm
□ Pull the camlock (C) and slide the leg to your desired length and
repeat on all four legs to ensure all legs are at the same height.
NOTE: Please make sure camlocks (C) are locked in place with
locking tabs fully engaged with corresponding holes on each leg.
□ Pull the latch (D) and then pull the support arm (E) to adjust the slots
to a width that properly ts your lumber dimensions.
□ The slots are designed to support lumber of 2 x 4, 3 x 4, 4 x 4.
5. Using the material support pegs and setting up a sawhorse
□ Unfold the material support pegs
(F) on the legs to hold materials.
NOTE: The maximum load is 80 NOTE: The maximum load is 80
lbs for each support peg (F). lbs for each support peg (F).
□ A pair of sawhorses can be
utilized to build a work table as
shown on the right.
Storage
Please adjust all legs' height to position four (4), then press the button labeled "CLOSE 1ST" to unfold the 1st set of legs then
repeat to unfold the second set of legs with care.
Please store in a cool, dry place and out of the reach of children.
Safety Information
CAUTION: Check the sawhorse to make sure it does not rock, slide or move before use.
Please make sure all components are secure before use.
Ensure that the sawhorse legs are fully extended with the leg braces in the lock-out position prior to use.
Please make sure all legs and foot are level and have solid contact with ground before use.
Please ensure work area is well lighted while working.
This sawhorse is designed for use on at, dry surfaces.
Prior to each use, inspect sawhorse for any damage and remove any obstacles or debris.
WARNING: Do not attempt to overload the sawhorse beyond a maximum capacity of 1300 lbs./589.7kg (max capacity of 2600
lbs./1179.4kg when using pair of sawhorses).
Never stack sawhorses to obtain extra height.
Always wear safety gloves, goggles or safety glasses with side shield, along with hearing protection.
Dress properly. DO NOT wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes,
jewelry or long hair can be caught in moving parts.
DO NOT let familiarity with tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe
injury within a fraction of a second.
Do not stand on sawhorse or work underneath it.
Do not use as a scaffold nor attempt to move the sawhorse in any manner when it is bearing weight.
B
D
C
F
E