Advertisement
Available languages
Available languages
6 | Français
Operation
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Products that are only sold in AUS and NZ: Use a resid-
u
ual current device (RCD) with a nominal residual current
of 30 mA or less.
Starting Operation
Pay attention to the mains voltage! The voltage of the
u
power source must match the voltage specified on the
rating plate of the power tool. Power tools marked
with 230 V can also be operated with 220 V.
Switching on/off
To switch on the power tool, press the on/off switch (3).
To lock the on/off switch (3), press and hold it while also
pushing the lock-on button for the on/off switch (2).
To switch off the power tool, release the on/off switch (3).
If the on/off switch (3) is locked, press the switch first and
then release it.
Working Advice
Never blow dirt in the direction of bystanders.
Always hold the power tool approx. 3 cm above ground
when working.
Do not blow hot, flammable or explosive material.
Ensure that the air inlet (7) cannot suck in any impurities
while blowing is taking place.
Maintenance and Service
Maintenance and Cleaning
Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
Replacing the carbon brushes (see figure B)
Check the length of the carbon brushes around every 2–3
months and replace both carbon brushes if required.
Never replace only a single carbon brush.
Note: Only use carbon brushes supplied by Bosch and inten-
ded specifically for your product.
– Unscrew the caps (4) using a suitable screwdriver.
– Replace the spring-loaded carbon brushes (8) and screw
the caps back on.
The criteria for replacing the carbon brushes: A dashed or
dotted line is present on one large side of the carbon brush.
If one of the two carbon brushes has been worn down to this
line, both carbon brushes should be replaced immediately in
order to protect the commutator from any potential damage.
1 609 92A 8WE | (20.10.2023)
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Malaysia
Robert Bosch Sdn. Bhd.(220975-V) PT/SMY
No. 8A, Jalan 13/6
46200 Petaling Jaya
Selangor
Tel.: (03) 79663194
Toll-Free: 1800 880188
Fax: (03) 79583838
E-Mail: kiathoe.chong@my.bosch.com
www.bosch-pt.com.my
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Disposal
The power tool, accessories and packaging should be re-
cycled in an environmentally friendly manner.
Do not dispose of power tools along with
household waste.
Français
Consignes de sécurité
Avertissements de sécurité généraux pour l'outil
électrique
Lire tous les avertissements de sé-
AVERTISSE-
curité, les instructions, les illustra-
MENT
tions et les spécifications fournis
avec cet outil électrique. Ne pas suivre les instructions
énumérées ci-dessous peut provoquer un choc électrique,
un incendie et/ou une blessure sérieuse.
Conserver tous les avertissements et toutes les instruc-
tions pour pouvoir s'y reporter ultérieurement.
Le terme "outil électrique" dans les avertissements fait réfé-
rence à votre outil électrique alimenté par le secteur (avec
cordon d'alimentation) ou votre outil électrique fonctionnant
sur batterie (sans cordon d'alimentation).
Bosch Power Tools
Advertisement
